EPEVER XDS2 XTRA Series

Contents

EPEVER XDS2 XTRA Series MPPT Solar Charge Controller User Manual

Model: XDS2 XTRA Series (10A-40A)

Brand: EPEVER

1. Product Overview

The EPEVER XDS2 XTRA Series MPPT Solar Charge Controller is an advanced maximum power point tracking (MPPT) charge controller designed for off-grid photovoltaic systems. It features optional display units (XDB1/XDS1/XDS2) and accessories. This series utilizes an advanced smart algorithm to maximize energy harvest from PV arrays, resulting in up to 30% higher charging efficiency compared to conventional pulse width modulation (PWM) charge controllers. The XTRA series offers extensive electronic protection against overcharge, over discharge, PV & battery reverse polarity, and more, ensuring system stability and durability.

Key Features:

  • Advanced MPPT technology with up to 99.5% tracking efficiency.
  • High DC/DC transfer efficiency, up to 97.4%.
  • Low temperature protection and self-activate function for lithium battery charging.
  • Limit charging power & current over rated range.
  • Real-time energy statistics function.
  • Multiple load working modes.
  • Comprehensive electronic protection.
  • Compatible with lead-acid and lithium-ion batteries.
  • Over temperature protection and power degrading in higher temperature.
  • Optional LCD display units (XDB1/XDS1/XDS2) and accessories.
  • High quality and low failure rate components.
  • Isolated RS485 communication port with 5V/200mA protected output, with standard Modbus protocol.
  • Monitor and set the parameters via APP or PC software.
  • Dustproof and waterproof design with IP32 protection class.
  • CE certification (LVD IEC62109, EMC EN3/1-6-61000).

Video: EPEVER XTRA Series MPPT Solar Charge Controller Overview and Features.

2. Safety Information

Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in severe injury, death, or damage to the controller and other equipment.

  • Ensure all wiring is correct and secure before powering on the system.
  • Do not disassemble or attempt to repair the controller yourself. Contact qualified personnel for service.
  • Keep the controller away from water, flammable gases, and corrosive substances.
  • Install the controller in a well-ventilated area to prevent overheating.
  • Use appropriate circuit breakers or fuses for all connections to prevent overcurrent.
  • The temperature sensor is crucial for proper battery charging. If it is short-circuited or damaged, the controller will charge or discharge according to the voltage setting point at the default temperature setting of 25°C (no temperature compensation).
  • When selecting lithium battery type, the system voltage cannot be identified automatically.
  • When a lead-acid battery is used, the controller does not have low temperature protection.

3. Product Components and Interface

EPEVER XTRA Series MPPT Charge Controller front view

Figure 1: Front view of the EPEVER XTRA Series MPPT Charge Controller.

EPEVER XTRA Series MPPT Charge Controller bottom view showing terminals

Figure 2: Bottom view showing connection terminals.

3.1 Product Characteristics Diagram

Product Characteristics Diagram with numbered components

Figure 3: Product Characteristics Diagram.

  1. RTS* port (Remote Temperature Sensor)
  2. PV Terminals
  3. Battery Terminals
  4. Load Terminals
  5. RS485 communication port
  6. Terminal protection cover
  7. Display units
  8. Mounting Hole Φ5mm

Note: If the temperature sensor is short-circuited or damaged, the controller will charge or discharge according to the voltage setting point at the default temperature setting of 25°C (no temperature compensation).

4. Setup and Installation

4.1 Connection Diagram

The following diagram illustrates a typical connection setup for the EPEVER XDS2 XTRA Series MPPT Solar Charge Controller in a solar power system. Ensure all connections are made in the correct order and polarity.

Connection Diagram for EPEVER MPPT Solar Charge Controller

Figure 4: System Connection Diagram.

Connection Steps:

  1. Connect the battery to the controller's battery terminals.
  2. Connect the solar panel(s) to the controller's PV terminals.
  3. Connect the load to the controller's load terminals.
  4. (Optional) Connect the Remote Temperature Sensor (RTS) to the RTS port.
  5. (Optional) Connect communication accessories (e.g., MT50 meter, eBox-WIFI-01, eBox-BLE-01, PC via RS485 to USB) to the RS485 communication port for monitoring and parameter setting.

Important: Always connect the battery first, then the solar panel, and finally the load. Disconnect in the reverse order.

4.2 Mounting Dimensions and Cable Recommendations

Table of Mounting Dimensions and Recommended Cable Sizes

Figure 5: Mounting Dimensions and Recommended Cable Sizes.

Refer to the image above for specific dimensions and recommended cable gauges for each model variant (XTRA 1206N, XTRA 2206N, XTRA 1210N, XTRA 2210N, XTRA 3210N, XTRA 4210N, XTRA 3215N, XTRA 4215N, XTRA 3415N, XTRA 4415N).

5. Operation

5.1 Advanced Display Unit (XDS2)

The XDS2 display unit provides real-time system status and allows for parameter configuration.

Advanced Display Unit (XDS2) details with indicators

Figure 6: XDS2 Display Unit and Indicators.

Indicator Lights:

IndicatorColorStatusInstruction
PVGreenOn SolidPV connection normal but low voltage (low irradiance) from PV, no charging
GreenOFFNo PV voltage (night time) or PV connection problem
GreenSlowly Flashing (1Hz)In charging
GreenFast Flashing (4Hz)PV Over voltage
GreenOn SolidNormal
BatteryGreenSlowly Flashing (1Hz)Full
GreenFast Flashing (4Hz)Over voltage
OrangeOn SolidUnder voltage
RedSlowly Flashing (1Hz)Battery Overheating, Lithium battery Low temperature
LoadYellowOn SolidLoad ON
YellowOFFLoad OFF
ControllerRedOn SolidController Overheating
SystemRedOn SolidSystem voltage error

5.2 Button Functions

Table of button functions for EPEVER XDS2 XTRA Series

Figure 7: Button Functions.

ButtonFunction
PV / +PV browsing interface
Setting data +
BATT / -BATT browsing interface
Cursor displacement during setting
Setting the battery type, battery capacity level and temperature unit.
LOAD / -Controller load browsing interface
Setting data -
SETEnter into setting interface
Setting interface switch to the browsing interface
Setting parameter as enter button
ESCExit the setting interface

5.3 Display Parameters and Setting Operations

Display parameters and setting operations for EPEVER XDS2 XTRA Series

Figure 8: Display Parameters and Setting Operations.

Display Information:

  • PV parameters: Voltage/Current/Power/Generated Energy
  • Battery parameters: Voltage/Current/Temperature/Battery capacity level
  • Load parameters: Voltage/Current/Power/Consumed energy/Load working mode-Timer1/Load working mode-Timer2

Setting Temperature Units:

  1. Press the SET button for the setting interface.
  2. Press the BATT / - button and hold 5s for the battery type interface.
  3. Press the SET button twice for the temperature unit interface.
  4. Press the PV / + or LOAD / - button to set the temperature units.
  5. Press the SET button to confirm the parameters.

Setting LCD Cycle Time:

The LCD cycle default time is 2s, the setting time range is 0~20s.

  1. Press the SET button for the setting interface.
  2. Press the PV / + button and hold 5s for the LCD cycle time interface.
  3. Press the PV / + or LOAD / - button to set the LCD cycle time.
  4. Press the SET button to confirm the parameters.

6. Technical Specifications

Technical Specifications Table for EPEVER XDS2 XTRA Series

Figure 9: Technical Specifications.

Electrical Parameters:

ItemValue (by model)
System Nominal Voltage12/24VDC Auto12/24/36/48VDC Auto
Rated Charge Current10A20A10A20A30A40A30A40A30A40A
Rated Discharge Current10A20A10A20A30A40A30A40A30A40A
Battery Voltage Range8~32V (for 12/24V models), 8~68V (for 12/24/36/48V models)
Max. PV Open Circuit Voltage60V100V150V
MPPT Voltage RangeBattery Voltage +2V ~ 36VBattery Voltage +2V ~ 72VBattery Voltage +2V ~ 108V
Max. PV Input Power (W)130/12V, 260/24V260/12V, 520/24V130/12V, 260/24V260/12V, 520/24V390/12V, 780/24V520/12V, 1040/24V520/12V, 1040/24V, 1560/36V, 2080/48V780/12V, 1560/24V, 2340/36V, 3120/48V520/12V, 1040/24V, 1560/36V, 2080/48V780/12V, 1560/24V, 2340/36V, 3120/48V
Equalization VoltageSealed: 14.6V, Flooded: 14.8V, User: 17-9V
Boost VoltageGel: 14.2V, Sealed: 14.4V, Flooded: 14.6V, User: 17-9V
Float VoltageGel/Sealed/Flooded: 13.8V, User: 17-9V
Low Voltage Reconnect VoltageGel/Sealed/Flooded: 12.6V, User: 17-9V
Low Voltage Disconnect VoltageGel/Sealed/Flooded: 11.1V, User: 17-9V
Self-consumption≤14mA(12V), ≤15mA(24V)≤22mA(24V)≤35mA(12V), ≤22mA(24V), ≤15mA(48V)
Discharge circuit voltage drop≤0.23V
Temperature Compensate coefficient-3mV/°C/2V (Default)
GroundingCommon negative grounding
RS485 interface5VDC/200mA (RJ45)
LCD backlight time60S (Default)

Environmental Parameters:

ItemValue
Working environment temperature (full rated power with no derating)-25°C ~ +50°C (LCD); -30°C ~ +50°C (No LCD)
Storage temp. range-20°C ~ +70°C
Relative humidity≤ 95%, N.C.
EnclosureIP32
Pollution degreePD2

Certification:

ItemStandard
SafetyEN/IEC62109-1
EMC (Emission immunity)EN61000-6-3/EN61000-6-1
FCC47 CFR Part 15, Subpart B
Performance & functionIEC62509
ROHSIEC62321-3-1

7. Troubleshooting

This section provides guidance on common issues you might encounter with your EPEVER XDS2 XTRA Series MPPT Solar Charge Controller.

  • No Display/Power: Check battery connections and voltage. Ensure the battery is adequately charged. Verify all wiring is secure and correct.
  • No Charging: Check PV panel connections and ensure sufficient sunlight. Verify PV voltage is within the controller's operating range. Check for any error indicators on the display.
  • Overheating: Ensure the controller is installed in a well-ventilated area. Check for obstructions around the heat sink. Reduce load if necessary. The controller has a power degrading feature to protect itself from high temperatures.
  • System Voltage Error: This can occur if the battery type is set incorrectly, especially for lithium batteries where auto-identification is not supported. Verify battery type settings.
  • Incorrect Temperature Readings: Check the RTS (Remote Temperature Sensor) connection. If damaged or short-circuited, the controller will use a default temperature.

For more complex issues, refer to the detailed troubleshooting guide in the full product manual or contact EPEVER customer support.

8. Maintenance

Regular maintenance ensures optimal performance and longevity of your solar charge controller.

  • Cleanliness: Keep the controller clean and free from dust and debris. Use a dry cloth to wipe the exterior.
  • Connections: Periodically check all wiring connections for tightness and corrosion. Loose connections can cause overheating and damage.
  • Ventilation: Ensure the installation area remains well-ventilated and free from obstructions to allow for proper heat dissipation.
  • Firmware Updates: Check the EPEVER website for any available firmware updates for your model to ensure you have the latest features and bug fixes.
  • Battery Health: Monitor your battery's health and ensure it is within its recommended operating parameters.

9. User Tips

  • Battery Type Setting: Always ensure the correct battery type is selected in the controller settings to prevent improper charging and potential battery damage. For lithium batteries, manual setting is required as auto-identification is not supported.
  • Monitoring: Utilize the RS485 communication port with compatible accessories (like an MT50 meter or PC/mobile software) to monitor system performance and adjust parameters for optimal efficiency.
  • Cable Sizing: Use the recommended cable sizes as specified in the technical specifications to minimize voltage drop and ensure safe operation.
  • Environmental Considerations: While the controller has IP32 protection, avoid exposing it to direct water spray or extreme humidity to prolong its lifespan.

10. Warranty and Support

EPEVER products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the official EPEVER website or contact your authorized dealer. Keep your purchase receipt as proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.