Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Hippcron 7-inch 1 Din Car MP5 Player. Please read this manual thoroughly before use to ensure proper functionality and safety. This unit features a 7-inch HD touch screen, wired CarPlay and Android Auto compatibility, Bluetooth for music and calls, FM radio, USB/TF card playback, and support for a rear view camera.
Figure 1: Hippcron 7-inch 1 Din Car MP5 Player
Safety Notice and Warnings
Read all instructions before installation. It is recommended that the machine be installed by a car audio professional.
- This machine is suitable for vehicle 12V power supply systems (the ground wire must be grounded). Do not install the machine in 24V vehicles, as it will damage the unit.
- Do not repair the power fuse without professional guidance. Improper use of the fuse can cause damage to the machine and cause a fire.
- To avoid violating traffic rules, drivers cannot watch videos while driving and operating machines to avoid unnecessary accidents.
- For the sake of safety and to ensure the normal use of the product, please invite professionals to install, disassemble, or repair the machine to avoid damage and accidents.
- Do not place this product in a humid environment or near water to prevent fire due to electric shock or other unnecessary damage.
Note: To prevent burning the machine, do not turn on the power until the power cord is properly connected!
Setup and Installation
Pre-Installation Test
Before full installation, perform a quick test to ensure the device is functioning correctly.
- Combine the red and yellow wires of the car stereo and connect them to the positive pole of the battery.
- Connect the black wire to the negative pole of the battery.
- After 2 seconds, check if the car stereo screen lights up. If it does, the car stereo is functioning properly.
Figure 2: Partial Wiring Display for Power Test. Red: +12V Ignition Switch, Black: Power Negative, Yellow: Power Positive.
Rear View Camera Test (Optional)
If you plan to use a rear view camera (purchased separately), test it before full installation:
- Maintain the Step 1 power connection.
- Connect the pink wire from the car stereo to the top red wire of the rear view camera.
- Combine the middle red wire and the bottom red wire of the rear view camera and connect them to the positive pole of the battery.
- Connect the black wire of the rear view camera to the negative pole of the battery.
- If the camera lights up and the car stereo shows the reverse image, the rear view camera is functioning properly.
Figure 3: Rear View Camera Test Wiring Diagram. Shows connections for Red, Black, Yellow, and Pink wires for camera functionality.
General Installation Guidelines
The size of this car stereo is universal, suitable for most cars. However, if the unit is not a direct fit, consider these methods:
- Aftermarket Accessories: You may need a Double DIN dash kit, a wire harness (to connect car wiring to stereo wiring), and an antenna adapter specific to your car's year, make, and model. These can be found by searching online.
- Original Frame Modification: Alternatively, you might need to modify the original frame of your car.
Important: Please check the speaker line carefully before installation. If any grounding or touching occurs, the unit may be damaged. The positive and negative terminals of the power supply must not touch or short circuit. Speaker wires must not touch each other or the power supply wires.
Wiring Diagram Reference
The specific wiring is subject to the actual product. Refer to the diagrams below for guidance.
Figure 4: Detailed Wiring Diagram Example 1. Shows connections for Left/Right Speakers, External Display, External Video Source, Rear View Camera, FM Radio, USB DVR, ACC, GND, ANT, ILL, KEY1, B+, Parking Check, Parking Sensor Control Wires.
Figure 5: Detailed Wiring Diagram Example 2. Shows connections for ILL (Illuminate Backlight), Steering Wheel Control (1 & 2), Reversing Camera Wires, Brake Detect, +12V Ignition Switch, Auto Antenna, Speaker Wires (Left/Right, Front/Rear), Ground Wire, +12V Constant Power Supply.
Machine Installation Methods
Different models may vary, but common installation methods include:
- Screw Fixed Installation: Securing the unit with screws.
- Card Position Fixed Installation: Using existing card slots for mounting.
- Special Frame Fixed Installation: Utilizing a custom frame for integration.
Figure 6: Various examples of car stereo installations.
User Tip: After installation, start the engine and put the car into reverse gear to check if the monitor automatically displays the rear view image. Adjust the camera angle so the rear bumper occupies about 5% of the screen for optimal safety.
Operating Instructions
Panel Functions
Familiarize yourself with the buttons and ports on the unit's front panel.
Figure 7: Front Panel Functions. Includes Last Song, Power/Mute, Next Song, Volume Adjustment, Main Menu, TF Card Slot, Reset, AUX, USB Port.
Video and Music Function Buttons
Common icons for video and music playback:
- HOME button: Returns to the main interface.
- The next song: Skips to the next track.
- Random pattern: Shuffles playback.
- Single/list loop: Repeats current track or playlist.
- Fast backward function: Rewinds.
- EQ: Sound shortcut key for equalizer settings.
- Pause/Play: Pauses or resumes playback.
- Return key: Navigates back.
Note: Due to different versions, icon functions may vary. This information is for reference only.
Radio Operation
To enter radio mode, click the "FM/Radio icon" on the menu. Press "FM" to select different bands (FM1/2/3). Use "AS/PS" to browse and auto-store stations. Hold "AS/PS" for 3 seconds to automatically store stations. Manual search is also available.
Video 1: Demonstration of FM Radio functionality (87.5-108MHz).
USB/TF Playback
Insert a USB flash drive or TF card into the designated slot to play videos and music. The USB interface also supports charging for your phone.
Audio/Video Input
Click on the application icon to enter the audio and video playback interface. Select the desired file to play. Supported formats include AVI, MKV, QT, MPG, ASF, FLV, RMVB, MP3, WMA, ACC, WAVE, FLAC, APE, OGG, MP4 for audio/video, and BMP, GIF, JPG, PNG for images.
Steering Wheel Control Learning
To program your steering wheel controls:
- Press any button on the steering wheel. The interface will display a prompt.
- Click on the screen to learn the docking function.
- Click the corresponding function button on the steering wheel and repeat steps 1-3 until all controls are set.
Requirements: Original steering wheel for non-bus control, voltage input control method.
Bluetooth (BT) Function
To connect via Bluetooth:
- Go to settings and click the BT icon.
- Search for the device (e.g., "CAR***").
- Pair by entering the PIN (default: 0000, 1234, or 88888888) if prompted.
Call Function: Input numbers on the screen to dial. Use the phone icon to dial and the hang-up icon to end calls.
Telephone Directory: Sync contacts by clicking the "Sync Contact" button. Search for contacts by entering English letters.
BT Music Playback: Connect your phone via BT. Play music from your phone, and control playback (play/pause/next/previous) from the car stereo.
Figure 8: Bluetooth Music and Call Interface. Shows phone connected for music playback and hands-free calling.
Mirrorlink (Optional)
Mirrorlink allows you to mirror your phone's screen to the car stereo. Click the "Mirrorlink Icon" menu to enter Phone link.
- For Android Devices (Wired): Connect your Android phone via USB. The unit will prompt you to install an APP. After installation, reconnect the USB cable. Screen mirroring will begin, allowing control from both the stereo and phone. Audio is transmitted via Bluetooth.
- For iPhone Devices (Wired): Connect your iPhone via USB and confirm the authorization request. Note that some high-configuration iPhones may not support this function, and control from the car stereo may not be available.
Figure 9: Mirror Link feature showing phone screen mirrored to car stereo for both iOS and Android phones.
Apple CarPlay (Wired)
This machine supports wired Apple CarPlay.
- Wired Connection: Connect your iPhone via a USB data cable. The unit will automatically enter the CarPlay interface.
Figure 10: Displaying CarPlay and Android Auto interfaces on the car stereo.
Android Auto (Wired)
This machine supports wired Android Auto.
- Download and install the "Android Auto" app from Google Play.
- A mobile phone with Android 6.0 or higher is required. Use a valid data cable.
- Wired Connection: Connect your Android phone via a USB data cable. The unit will automatically enter the Android Auto interface.
Reversing Camera Connection (CCD)
The reversing video input connects via an RCA adapter cable. When a signal is detected, the LCD automatically switches to the camera image. (Camera is purchased separately).
- If the rearview camera is not installed, it will display "No Signal".
- "Rearview Cam" can be triggered by pressing the icon on the main interface or by engaging the reverse gear.
Safety Warning: When driving normally, avoid turning on the rearview camera to prevent distraction.
Figure 11: Rear Camera Support showing reverse image with guidelines on screen.
Troubleshooting Guide
This section provides solutions to common issues. If problems persist, consult a professional.
| Problem | Cause and Resolve |
|---|---|
| Power off | Check if the power fuse has burned out and replace it. If there is a failure in the connection of the DC wires, reconnect them. |
| Fail in keying | Program disorder, press reset button or turn off the power to restart. |
| Fail in getting stations | Check whether the antenna has been inserted or connected correctly. If not, please insert the antenna or connect it correctly. |
| Poor radio reception | 1. Antenna length may not be set up right, check if it reaches out completely or is broken down. If broken, change it. 2. Radio signal is too weak. 3. Antenna is not grounding correctly, confirm connection. |
| "STEREO" flashing | 1. Tuning the radio frequency accurately. 2. Radio signal is too weak (press ST button to turn off stereo). |
| Noise, image jumping, no color | The disc is damaged or blurry. The color system setup is not correct. Set the color system to "PAL" or "NTSC" according to the connected TV condition. |
| Remote unavailable | 1. The battery of the remote control has no power. Please change the battery. 2. The remote control window is unable to receive the signal. Make sure to aim the remote control at the model's remote receiver window. |
| USB no reading | The connection is not correct. This card is unsupported. |
| Car radio not turning on, or turns off after prolonged use. | 1.1 Ensure the red cable is connected to the ignition-positive terminal, the yellow cable to the battery-positive terminal (B+ 12V), and the black cable to the battery-negative terminal (GND 12V). Use the radio only in a 12V-output vehicle. 1.2 If the radio remains off after confirming correct wiring, temporarily connect the red and yellow cables together and attach them to the 12V-positive terminal. 1.3 If the radio still does not power on, check whether the fuse is blown. |
| Car radio powers on but produces no sound, or sound cuts out during playback. | 1. Speaker negative wires are improperly grounded. 2. The amplifier IC is burned out due to a short circuit in the wiring. 2.1 Check if any speaker cables have a short circuit, and ensure each one is individually insulated. 2.2 If you confirm that the wire is correctly wired, you can find a speaker elsewhere to do an extra test, which could easily confirm the problem is from the radio or your car's system. |
| Car radio's BT is not working, or it works for a while then disconnects itself. | 3.1 Forget the device: Go to your phone's BT settings → Select "CAR-MP5" → Tap Forget This Device. Re-pair the device: Turn on the MP5's BT → Scan for devices on your phone → Select "CAR-MP5". Enter PIN (if prompted): Use 0000, 1234, or 88888888 (default codes). 3.2 If the last step can't make the BT back, try to find the "reset hole" on the front panel and do the reset for a try. If it's convenient enough, you can also try to unhook the power connector behind for a few minutes and replug it in later. |
| Car radio's mic is not working, phone call from the other side can't hear clearly. | 4.1 Try to check the BT volume setting. 4.2 Try to check if the dashboard is too low (the mic is too far for you) for the radio's mic to collect your voice. |
| Car radio cannot read your USB flash disk or SD/TF card. | Please confirm the capacity of the USB flash disk or SD memory card. It can read lower than 32GB normally. Please use other flash disks with fewer songs to test again (confirm if you insert the SD/TF card in the correct side). |
| Car radio's remote control does not work. | Please check if the remote has the correct battery inside. |
| The reversing camera cannot work in the radio. | If you can check the pink cable is wired correctly with the reversing camera's controlling cable. If you don't know how to wire it, you can also contact us for advice. |
| Car radio cannot save the time or radio station setting. | Check if the Yellow cable is wired with your car's battery 12V+ (constant positive) or not, it provides constant power to the unit and saves the setting. |
| Car radio noise problem. | 9.1 For some cars, there might be some noise generated in the playing. Especially when you are using an amplifier. Usually, this kind of problem is related to interference. Please make sure all the cables are wrapped well in case of any contact with each other. 9.2 You can find a speaker elsewhere to do an extra test, which could easily confirm the problem is from the radio or your car's system. |
| Screen Mirroring Failure | Step 1: Check device compatibility: Ensure your phone supports Mirroring. Step 2: Enable car's Wi-Fi/BT → Activate phone's screen mirroring → Select "CAR-MP5". Step 3: No signal? Restart both devices. Note that some phones do not support phone mirroring and are not compatible. |
Specifications
| Feature | Specification |
|---|---|
| Display Size | 7 inches |
| Resolution | 800*480 |
| Touch Screen | Yes |
| Din Size | One Din |
| Out Power | 60W |
| Voltage | 12 V |
| Item Weight | 0.7kg |
| Item Size | 180*105mm |
| Max External Memory | 32G |
| TF/Micro SD Slot | 1 |
| Special Features | CarPlay, Android Auto, Reversing Input |
| Digital Media Format | Mp3, MP4, JPEG |
| OSD Language | Chinese (Simplified), Polish, Russian, French, Korean, Spanish, English |
| Preset Station (FM) | 87.5-108MHz (18 preset stations) |
| Bluetooth | Bluetooth 5.0, supports advanced audio distribution profile |
| USB Port | USB 2.0, supports charging |
| Audio Playback Formats | MP3/WMA/WAV/FLAC/OGG/APE |
| Video Playback Formats | RM/RMVB/DVD(VOB)/VC-D(DAT)/MP1/MP2/DIVX/XV1D/MP4/H263/H264/FLV/3GP/SWF/AVI/ASF/MJPEG |
| Remote Control Battery | CR2025 3V (not included) |
| Working Temperature | -20 - 70 degrees Celsius |
| Certification | CE |
Figure 12: Product Dimensions (180mm x 105mm).
User Tips
- CarPlay/Android Auto Connectivity: Ensure you use a quality USB data cable for stable wired CarPlay and Android Auto connections. Some users report issues with generic cables.
- Bluetooth Pairing: If you experience issues with Bluetooth disconnecting, try forgetting the device on your phone and re-pairing. If problems persist, a unit reset might help.
- Rear Camera Installation: Properly adjust the rear camera angle during installation to ensure the car's bumper is visible, providing a clear reference for parking.
- Steering Wheel Controls: Take your time to program the steering wheel controls carefully, following the learning steps provided in the manual for a personalized experience.
Warranty and Support
This product comes with a 1-year warranty.
For further questions or support, please contact customer service. Product UI or functions may be modified and upgraded over time without notice. Any discrepancies in the manual are normal.
You can also refer to the User Manual (PDF) for additional information.
