Flysky FS-IBG01

Contents

Flysky FS-IBG01 GPS Module User Manual

Model: FS-IBG01 | Brand: Flysky

Introduction

The Flysky FS-IBG01 is a high-precision GPS module designed for various RC applications, including cars, boats, planes, and robots. It supports multiple satellite systems, specifically GPS and Beidou, to provide accurate and reliable positioning data. This module features high sensitivity, short acquisition time, strong anti-interference capabilities, and is engineered for low power consumption, making it an ideal choice for enhancing the navigation and telemetry of your remote-controlled models.

Front view of the Flysky FS-IBG01 GPS Module
Figure 1: Front view of the Flysky FS-IBG01 GPS Module.

Setup

Follow these steps to properly install and connect your FS-IBG01 GPS Module:

  1. Physical Installation:

    Mount the GPS module securely on your RC model. Ensure it has a clear, unobstructed view of the sky for optimal satellite reception. The module's installation direction is indicated on its casing. An optional bracket may be used for mounting.

    Diagram of FS-IBG01 GPS Module interfaces and optional bracket
    Figure 2: Module interfaces and optional bracket. [1] i-BUS2 Output Interface, [2] LED Indicator Light, [3] Installation Direction Indication, [4] Bracket (optional).
  2. Wiring Connection:

    Connect the module's i-BUS2 Output Interface [1] to a compatible i-BUS2 port on your RC receiver or flight controller. Ensure the polarity is correct to prevent damage. The module operates on an input power of 3.5 - 9V/DC.

  3. Initial Power-up:

    Upon first power-up, the module will perform a self-test. The LED Indicator Light [2] will show a White Steady On state for approximately 3 seconds during this process.

Operating

Once installed and powered, the FS-IBG01 GPS Module will begin searching for satellite signals. Its operational status is indicated by the LED light:

  • Red Steady On: The module is powered on but has not yet acquired a GPS fix (not positioned).
  • Blue Slow Blink: Satellite search and positioning are successful, and the module is working normally, providing accurate location data.
  • Green Steady On: Indicates that the gyroscope has been calibrated. This state may be relevant for specific flight controller integrations.
  • White Steady On: Occurs during the initial self-test phase (approximately 3 seconds after power-up).
LED light indications for FS-IBG01 GPS Module
Figure 3: LED status indicators for the GPS module.

The FS-IBG01 supports a dual-satellite system, utilizing both GPS and Beidou satellites for enhanced positioning accuracy and reliability. In dual-mode, the speed measurement accuracy is 0.05 m/s, and the positioning accuracy is better than 0.5 meters.

Diagram illustrating dual-satellite system (GPS and Beidou) positioning
Figure 4: Dual-satellite system support for improved accuracy.

Maintenance

The FS-IBG01 GPS Module is designed for durability and requires minimal maintenance. To ensure optimal performance and longevity:

  • Keep the module clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning.
  • Regularly inspect the connection cable for any signs of wear, fraying, or damage. Ensure it is securely plugged into the i-BUS2 interface.
  • Avoid exposing the module to extreme temperatures outside its specified operating range (-10℃ to +60℃) or high humidity (20% to 95%).
  • Ensure the module is mounted in a location that minimizes vibration and physical impact during operation.

Troubleshooting

If you encounter issues with your FS-IBG01 GPS Module, refer to the following common troubleshooting steps:

  • No LED Light / Module Not Powering On:

    Check the power connection to the i-BUS2 interface. Ensure the input voltage is within the specified range of 3.5 - 9V/DC. Verify that the receiver or flight controller is providing power correctly.

  • LED is Red Steady On (No GPS Fix):

    This indicates the module is powered but has not acquired satellite signals. Move your RC model to an open area with a clear view of the sky, away from tall buildings, dense foliage, or strong electromagnetic interference. Allow sufficient time (up to 26 seconds for a cold start) for the module to acquire satellites.

  • Inaccurate Positioning Data:

    Ensure the module is mounted correctly with the installation direction indication facing upwards or as per your RC system's requirements. Verify there are no obstructions directly above the module. Strong local interference can also affect accuracy.

  • Module Not Communicating with Receiver/Flight Controller:

    Double-check the i-BUS2 connection. Ensure the receiver/flight controller is configured to accept data from an i-BUS2 GPS module. Consult your receiver/flight controller manual for specific setup instructions.

Specifications

FeatureSpecification
Product ModelFS-iBG01
Supported Satellite SystemsGPS | Beidou
Compatible ModelsCars, boats, planes, robots, etc.
Tracking Sensitivity-167dBm
Acquisition Sensitivity-160dBm
Cold Start Sensitivity-148dBm
Hot Start Sensitivity-157dBm
Cold Start TimeAverage 26s
Hot Start TimeAverage 1s
Positioning Accuracy0.3 degrees (better than 0.5m in dual-mode)
Speed Measurement Accuracy0.05 m/s
Time AccuracyRMS 99% 30ns
Maximum Altitude50,000m
Acceleration≤ 4g
LED DisplayYes
Update Rate10Hz
Data Formati-BUS2
Input Power3.5 - 9V/DC
Temperature Range-10℃ ~ +60℃
Humidity Range20% ~ 95%
Dimensions40.2*40.2*18.5mm
Weight24.1g
Appearance ColorBlack
CertificationCE, FCC

User Tips

To maximize the performance and reliability of your Flysky FS-IBG01 GPS Module:

  • Optimal Placement: Always mount the GPS module in a location with the clearest possible view of the sky, away from other electronics that might cause interference.
  • First Fix Patience: The first time you power on the module in a new location (cold start), it may take longer to acquire satellites. Be patient and ensure it has an unobstructed view.
  • Firmware Updates: Periodically check the Flysky official website for any available firmware updates for the FS-IBG01 module or your compatible receiver/flight controller. Updates can improve performance and add new features.
  • Cable Management: Secure all wiring to prevent accidental disconnections or damage during operation, especially in high-vibration environments.

Warranty and Support

For warranty information, technical support, or service inquiries regarding your Flysky FS-IBG01 GPS Module, please contact the retailer where you purchased the product or refer to the official Flysky website for manufacturer support details. Keep your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.