1. Introduction
This manual provides instructions for the setup, operation, and maintenance of your Nice FLO4RS Garage Door Remote Control. This remote operates on a 433.92MHz frequency and utilizes rolling code technology for enhanced security. It is designed to be paired directly with compatible Nice FLO2RS garage door openers and receivers.
Important Note: This remote control cannot be cloned. Access to your receiver/opener is required for successful programming. Please ensure you have access to your receiver/opener before attempting to program the remote.
2. Safety Information
- Keep remote controls out of reach of children.
- Do not allow children to operate the garage door opener.
- Ensure the garage door area is clear of people and objects before operating.
- Do not expose the remote control to water or extreme temperatures.
- Dispose of batteries properly according to local regulations.
3. Package Contents
- 3 x Nice FLO4RS Garage Door Remote Controls
- Batteries (pre-installed)
4. Specifications
| Feature | Specification |
|---|---|
| Type | Programming with the receiver |
| Frequency | 433.92MHz |
| Code Type | Rolling Code |
| Buttons | 4 |
| Battery | Included |
| Certification | CE |
| Dimensions (L x W x H) | 12 cm x 9 cm x 4 cm (approximate package dimensions) |
| Weight | 0.104 kg (approximate package weight) |
5. Setup and Programming
To program your Nice FLO4RS remote control, you must have access to your garage door opener's receiver. The remote uses rolling code technology and cannot be duplicated from another remote directly. Follow these steps to pair your new remote with the receiver:
- Locate the 'Match' or 'Learn' button on your garage door opener's receiver.
- Press the Receiver Match button. The LED indicator on the receiver should light up.
- Immediately press and hold one of the buttons on your new Nice FLO4RS remote control.
- Continue holding the remote button. The LED on the receiver will go out.
- Release the remote button, then press and hold it again for 3-5 seconds.
- The LED on the receiver should blink 3 times and then blink rapidly, indicating successful matching.
- Test the remote control to ensure it operates the garage door correctly.
Compatibility Check:
Ensure your existing system uses rolling code technology. Remotes with DIP switches (fixed code) are not compatible with this rolling code remote.
Programming Demonstration Video
Video 1: Step-by-step guide on how to program the remote control with a receiver.
6. Operating Instructions
Once programmed, operating your Nice FLO4RS remote control is straightforward:
- Press any of the four buttons on the remote control to activate your garage door opener.
- The door will open or close with each press, depending on its current state.
- Ensure you are within range of the receiver for reliable operation.
7. Maintenance
- Cleaning: Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement: If the remote's range decreases or the LED indicator on the remote does not light up when a button is pressed, the battery may need replacement. Refer to the remote's casing for instructions on how to open it and replace the battery.
- Storage: Store the remote in a dry place, away from direct sunlight and extreme temperatures.
8. Troubleshooting
- Remote not working after programming:
- Ensure you followed all programming steps correctly. Repeat the programming process.
- Verify that your garage door opener's receiver is compatible with rolling code remotes.
- Check the remote control's battery.
- Limited range:
- Replace the remote control's battery.
- Ensure there are no obstructions between the remote and the receiver.
- Check for sources of radio interference in the area.
- Remote LED not lighting up:
- The battery may be dead or incorrectly installed. Replace the battery.
- Remote cannot be cloned:
- This remote uses rolling code technology for security and cannot be cloned from another remote. It must be programmed directly to the receiver.
9. User Tips
- Always keep a spare remote control or ensure alternative access to your garage in case of remote loss or malfunction.
- Familiarize yourself with the location of your receiver's 'Match' or 'Learn' button before you need to program a new remote.
- If you have multiple garage doors with compatible openers, you can program each remote to control different doors using different buttons, if your opener supports it.
10. Warranty and Support
For any issues or questions regarding your Nice FLO4RS remote control, please contact the seller or manufacturer for assistance. Keep your purchase records for warranty claims.
