LYZRC L900 PRO SE MAX / L900Pro Se / L900PRO

Contents

Instruction Manual for LYZRC L900 PRO SE MAX / L900Pro Se / L900PRO GPS RC Drone Spare Parts

Introduction

This manual provides detailed instructions for the replacement and maintenance of the HD Camera and Blade Propellers for your LYZRC L900 PRO SE MAX, L900Pro Se, or L900PRO GPS RC Drone. Please read these instructions carefully before attempting any installation or replacement to ensure proper function and safety.

Setup and Replacement

Before beginning any replacement procedure, ensure your drone is powered off and the battery is disconnected to prevent accidental activation or damage.

1. HD Camera Replacement

The HD camera module is designed for easy replacement. Follow these steps:

  1. Carefully locate the existing camera module on your LYZRC L900 PRO SE MAX/L900Pro Se/L900PRO drone.
  2. Gently disconnect the wiring harness that connects the camera to the drone's main board. Note the orientation of the connector.
  3. Remove any retaining screws or clips holding the old camera module in place.
  4. Position the new HD camera module (as shown in the image below) into the drone's camera housing.
  5. Secure the new camera module with the retaining screws or clips.
  6. Connect the wiring harness from the new camera module to the drone's main board, ensuring the correct orientation.
  7. Verify that the camera is securely mounted and the connection is firm.
LYZRC L900 PRO SE MAX HD Camera module and 16 blade propellers with screws
Image: LYZRC L900 PRO SE MAX HD Camera module (bottom left) with its wiring harness, and 16 blade propellers (top left and right) along with various small screws for attachment.

2. Blade Propeller Replacement (16 PCS)

The propeller set includes 16 blades, allowing for full replacement and spares. Follow these steps:

  1. Identify the propeller(s) that need replacement. Note the direction of rotation and the type of propeller (A or B, usually marked on the blade or drone arm).
  2. Using a small screwdriver, carefully remove the screw(s) holding the damaged propeller to the motor shaft.
  3. Remove the old propeller.
  4. Take a new propeller from the 16-piece set, ensuring it matches the type (A or B) and orientation of the one being replaced.
  5. Place the new propeller onto the motor shaft, aligning it correctly.
  6. Secure the new propeller with one of the provided screws. Do not overtighten, but ensure it is firm.
  7. Repeat for all necessary propeller replacements. It is recommended to replace propellers in pairs (e.g., both front left and front right) for balanced flight.

Operating Considerations After Part Replacement

After replacing any spare parts, it is crucial to perform a thorough check before operating your drone.

  • Visual Inspection: Ensure all new parts are securely fastened and there are no loose wires or components.
  • Propeller Balance: Gently spin each propeller by hand to ensure it rotates freely and without obstruction. Check for any wobbling.
  • Camera Functionality: Power on the drone and connect to the control app. Verify that the camera feed is clear and responsive. Test camera controls like tilt and pan if applicable to your drone model.
  • Test Flight: Perform a low-altitude, slow test flight in an open, safe area to confirm stability and control before full operation.

Maintenance

Regular maintenance of your drone's spare parts will extend their lifespan and ensure optimal performance.

  • Propellers: Regularly inspect propellers for cracks, bends, or chips. Even minor damage can affect flight stability. Replace damaged propellers immediately. Keep them clean from dust and debris.
  • Camera Lens: Keep the camera lens clean using a soft, lint-free cloth. Avoid abrasive materials that could scratch the lens.
  • Connections: Periodically check all wiring connections for looseness or corrosion.
  • Storage: Store spare parts in a dry, cool place away from direct sunlight and extreme temperatures.

Troubleshooting Common Issues

Drone unstable after propeller replacement:
Ensure all propellers are installed correctly according to their A/B markings and are securely fastened. Check for any bent or unbalanced propellers. Replace if necessary.
No camera feed or poor image quality:
Verify that the camera's wiring harness is fully and correctly connected. Check for any damage to the camera module or its cable. Ensure the lens is clean and free from obstructions.
Screws are loose after flight:
Always check propeller screws before each flight. If screws repeatedly loosen, consider using a tiny drop of non-permanent threadlocker (e.g., Loctite Blue 242) on the screw threads, but be extremely careful not to get it on plastic parts or the motor itself.

Specifications

FeatureDetail
Product TypeHD Camera Module & Blade Propellers (16 PCS)
CompatibilityLYZRC L900 PRO SE MAX, L900Pro Se, L900PRO GPS RC Drones
Camera ResolutionFull HD (as indicated on camera module)
Camera FOV108° (as indicated on camera module)
Camera ApertureF/2.2 (as indicated on camera module)
Propeller Quantity16 pieces
MaterialComposite Material
OriginMainland China
Is ElectricNo Battery
Batteries IncludedNo
Recommended Age3-6Y, 6-12Y, 14+y
UseVehicles & Remote Control Toys
Package Weight0.08 kg
Package Dimensions (L x W x H)1 cm x 1 cm x 1 cm (Approximate)

User Tips

  • When replacing propellers, always ensure you use the correct type (A or B) for each motor to maintain proper lift and flight stability. Mixing propeller types can lead to unstable flight.
  • Keep a few spare propellers handy, as they are the most common parts to be damaged during crashes or hard landings.
  • Before installing the new camera, gently clean the lens with a microfiber cloth to ensure optimal image clarity from the start.
  • If you experience any difficulty with the camera connection, double-check the small white connector for proper alignment and ensure it is fully seated.

Warranty and Support

For any warranty claims, technical support, or further assistance with your LYZRC drone spare parts, please contact the seller directly through the platform where you made your purchase. Provide your order details and a clear description of the issue for prompt support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.