1. Introduction
The Creality Falcon YW45 Desktop Smoke Purifier is designed to provide a dust-free and healthy workspace, especially when operating laser engraving and cutting machines like the Creality Falcon A1. It features a dual-layer filtration system, adjustable fan speeds, and low noise operation to efficiently capture debris, harmful gases, and unpleasant odors, ensuring a safer creative environment.
2. Safety Information
Please read all safety instructions carefully before using the device to prevent injury or damage. Keep this manual for future reference.
- Ensure the power supply matches the device's requirements (AC100-240V).
- Do not operate the device with wet hands or in damp environments.
- Keep the device away from flammable materials.
- Do not block the air inlet or outlet during operation.
- Unplug the device before performing any maintenance or filter replacement.
- Keep out of reach of children.
- Only use original or approved replacement filters.
3. Package Contents
Verify that all items are present in your package:
- Smoke Purifier Unit (1)
- Power Adapter (1)
- Exhaust Pipe (1)
- User Manual (This document)
4. Setup
Follow these steps to set up your Creality Falcon YW45 Desktop Smoke Purifier:
- Placement: Place the smoke purifier on a stable, flat surface near your laser engraving or cutting machine. Ensure there is adequate space around the unit for proper airflow.
- Connect Exhaust Pipe: Connect one end of the exhaust pipe to the air inlet interface (Φ55 Flange) on top of the purifier. The purifier supports dual-size exhaust pipes (63mm for Falcon A1, 76mm for other Falcon series machines/covers). Connect the other end of the exhaust pipe to your laser machine's exhaust port or protective cover.
- Power Connection: Connect the power adapter to the purifier's power input port, then plug the adapter into a standard AC100-240V power outlet.
5. Operating Instructions
The Creality Falcon YW45 features simple controls for efficient operation.
5.1 Controls
- ON/OFF Button: Located on the front panel, this button powers the unit on or off.
- FLOW Button: Also on the front panel, this button adjusts the fan speed.
5.2 Powering On and Adjusting Speed
- Press the ON/OFF button to turn on the smoke purifier. The indicator light will illuminate.
- Press the FLOW button to cycle through the three available fan speeds (Speed 1, Speed 2, Speed 3). Select the speed appropriate for your engraving or cutting task. Higher speeds provide stronger suction and filtration.
- To turn off the purifier, press the ON/OFF button again.
6. Maintenance
Regular maintenance ensures optimal performance and longevity of your smoke purifier.
6.1 Filter System
The purifier uses a dual-layer efficient filtration system consisting of a pre-filter and an activated carbon filter. This system achieves 99.97% purification.
- Pre-filter: Traps larger visible particles, such as accumulated dust.
- Activated Carbon Filter: Features a honeycomb structure, filtering 99.97% of 0.03µm particles and absorbing harmful gases and unpleasant odors.
6.2 Filter Replacement
The filter can be replaced separately, and the use cost is low. Replace filters regularly based on usage and the type of materials being processed.
- Unfasten the latch and remove the cover.
- Take out the used filter cartridge.
- Insert the new replacement cartridge.
- Close the cover and start using it.
6.3 Cleaning
- Wipe the exterior of the unit with a soft, dry cloth.
- Do not use abrasive cleaners or solvents.
- Ensure the unit is unplugged before cleaning.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Purifier does not turn on. | No power supply. | Check if the power adapter is securely plugged into the unit and the wall outlet. Ensure the outlet is functional. |
| Weak suction or poor purification. | Clogged or old filter. Blocked air inlet/outlet. Incorrect fan speed. |
Replace the filter cartridge. Ensure air inlet and outlet are clear of obstructions. Increase fan speed using the FLOW button. |
| Unusual noise during operation. | Foreign object inside. Unit not stable. |
Turn off and unplug the unit. Carefully inspect for any foreign objects. Ensure the unit is placed on a stable, flat surface. |
8. Specifications
| Parameter | Value |
|---|---|
| Product Name | Creality Falcon Smoke Purifier |
| Air Inlet Interface | Φ55 Flange (Supports 63mm and 76mm exhaust pipes) |
| Input Voltage | AC100~240V |
| Power | 45W |
| Filtration Efficiency | 0.3µm 97.0% (Dual-layer achieves 99.97%) |
| Sound Level | <68dB (typically 58-66.7dB) |
| System Flow | 115m³/h |
| Product Size (L*W*H) | 185*185*205mm (7.28*7.28*8.07 inches) |
| Net Weight | 3.77kg (8.31 lbs) |
| CE Certification | Yes |
9. User Tips
- For optimal smoke and odor removal, ensure a tight seal between the exhaust pipe and both the purifier and your laser machine. Any leaks can reduce efficiency.
- Regularly check the filter for visible debris and replace it promptly when suction power decreases or odors persist. This maintains air quality and device performance.
- Consider the type of material being processed; some materials produce more fumes and may require more frequent filter changes.
- While the device operates quietly, using it in a well-ventilated area is always recommended for overall air quality and safety.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official Creality website or contact your authorized dealer. Keep your purchase receipt as proof of purchase for any warranty claims.
