1. Introduction
Thank you for choosing the LEKATO 9V DC Power Adapter with 6-Way Daisy Chain. This product is designed to provide stable and reliable power to your guitar effect pedals, keyboards, and portable amplifiers. Please read this manual carefully before use to ensure proper operation and to prevent damage.

2. Safety & Warnings
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
- Read and follow all instructions and heed all warnings.
- Keep the device and its cord out of reach of children under 3 years old. In case of ingestion, seek medical attention immediately.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Use only attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
- Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
Correct Disposal of this Product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information, please contact your local city office or your household waste collection service.
This product conforms with all applicable European Union regulations. The CE marking confirms that the product meets essential requirements for health, safety, environmental protection, and consumer protection as laid down in EU directives.
3. Product Overview
The LEKATO 9V DC Power Adapter is designed for musicians requiring a reliable power source for multiple effects pedals or other compatible devices. It features a single power adapter and a 6-way daisy chain cable.
3.1 Package Contents
- 1 x 9V DC Power Adaptor
- 1 x 1 to 6 Ways Daisy Chain Cable

4. Specifications
| Feature | Description |
|---|---|
| Brand Name | LEKATO |
| Model Number | 6 Ways Power Adapter |
| Type | Audio Cable (Power Supply) |
| Input | AC 100-240V, 50-60Hz, 0.4A |
| Output | DC 9V, 1500mA (1A 9W) |
| Polarity | Tip Negative (-) Design (Central Negative) |
| Connector Size | 5.5mm*2.1mm |
| Daisy Chain | 1 to 6 Ways |
| Power Cable Length | Approx. 59 inches (1.5 meters) |
| Weight | 160g / 5.64 ounces |
| Protections | Over-Current, Over-Voltage, Overload, Short Circuit, Temperature |



5. Setup Instructions
Follow these steps to set up your LEKATO 9V DC Power Adapter:
- Verify Device Compatibility: Ensure all devices you intend to power require a 9V DC input with a tip-negative polarity and a 5.5mm*2.1mm connector. Check the power requirements of each pedal/device to ensure the total current draw does not exceed 1500mA (1.5A).
- Connect Daisy Chain: Connect the single male plug of the 6-way daisy chain cable to the output of the 9V DC power adapter.
- Connect Devices: Plug the individual plugs of the daisy chain cable into the power input jacks of your guitar pedals, keyboards, or portable amplifiers.
- Connect Power Adapter: Plug the 9V DC power adapter into a standard AC wall outlet (100-240V, 50-60Hz).
- Power On Devices: Once all connections are secure, power on your devices.

6. Operating Instructions
The LEKATO 9V DC Power Adapter is designed for simple plug-and-play operation:
- Ensure all connections are firm and correct before applying power.
- The power adapter provides a stable 9V DC output. It features professional noise isolation to minimize interference.
- The 6-way daisy chain allows you to power up to six compatible devices simultaneously from a single power source.
- Always turn off your devices and unplug the power adapter from the wall outlet when not in use for extended periods.
7. Maintenance
To ensure the longevity and optimal performance of your power adapter:
- Cleaning: Use a dry, soft cloth to clean the adapter and cables. Do not use alcohol or other cleaning fluids.
- Storage: Store the power adapter and cables in a cool, dry place away from direct sunlight, heat sources, and moisture when not in use.
- Cable Care: Avoid bending or kinking the cables sharply. Do not place heavy objects on the cables.
- Inspection: Periodically inspect the power adapter and cables for any signs of damage, such as frayed wires or cracked casings. If damage is found, discontinue use immediately and seek qualified service personnel.
8. Troubleshooting
If you encounter issues with your LEKATO 9V DC Power Adapter, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No power to devices |
|
|
| Humming or noise from pedals |
|
|
| Adapter feels hot |
|
|
9. User Tips
- Check Polarity: Always double-check the polarity of your pedals. This adapter is "tip negative". Using the wrong polarity can damage your pedals.
- Current Management: While the adapter provides 1500mA, individual pedals draw different amounts of current. Ensure the sum of current drawn by all connected pedals does not exceed the adapter's maximum output to prevent underpowering or damage.
- Cable Management: Use cable ties to keep your daisy chain and power cables tidy, reducing trip hazards and improving the aesthetics of your setup.
- Testing: Before a performance or important session, test your entire pedalboard setup to ensure all pedals are receiving adequate power and functioning correctly.
10. Warranty and Support
For warranty information or technical support, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.