Silverflo 938BD-III

Contents

Silverflo 938BD-III 2-in-1 Soldering and Rework Station User Manual

Model: 938BD-III

Important Safety Guidelines

Strictly follow the basic safety guidelines and precautions when using the product. The guidelines include:

CAUTION!!! WARNING!!!

  • Read the instruction manual carefully before using the device.
  • To provide continued protection against the risk of electric shock, connect only to properly grounded outlets.
  • Do not immerse the unit in water.
  • Hot Surface. Avoid direct contact with heated components.
  • Shock Hazard. To provide continued protection against electric shock, disconnect from the power supply when not in use.
  • The heat gun, soldering iron, and desoldering iron must be placed on their respective stands when not in use.
  • For household and indoor use only.
  • To prevent electric shock, unplug the unit before replacing the fuse or performing any other service. Replace only with the same type and rating of fuse.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.
  • The soldering iron and desoldering iron are only to be used with the power supply unit provided with the appliance.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
  • Any servicing should be performed by an authorized service representative. The product has no user-serviceable parts.
  • To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Store indoors.
  • A fire may result if the appliance is not used with care. Be careful when using the appliance near combustible materials. Do not apply heat to the same spot for a long time. Do not use in the presence of an explosive atmosphere. Be aware that heat may be conducted to combustible materials that are out of sight. Place the appliance on its stand after use and allow it to cool down before storage. Do not leave the appliance unattended when it is switched on.
  • Hidden areas such as behind walls, ceilings, floors, soffit boards, and other panels may contain flammable materials that could be ignited by the heat gun when working in these locations. The ignition of these materials may not be readily apparent and could result in property damage and injury. When working in these locations, keep the heat gun moving in a back-and-forth motion. Lingering or pausing in one spot could ignite the panel or the material behind it.
  • WARNING: Extreme care should be taken when stripping paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Any pre-1977 paint may contain lead, and paint applied to homes prior to 1950 is likely to contain lead. Exposure to even low levels of lead can cause irreversible brain and nervous system damage; young and unborn children are particularly vulnerable. LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL AND SHOULD NOT BE REMOVED USING A HEAT GUN.
  • To ensure personal safety, turn off the power switch after work is completed. When not in use for an extended period, unplug the power cord.
  • Do not install nozzles when the hot air gun is turned on; the heat pipe and nozzle must be cool.
  • The soldering iron should only be used for soldering. Do not hit the soldering iron against the work surface to remove flux residues (use the cleaning device).
  • Soldering produces fumes; ensure adequate ventilation.
  • After use, allow the unit to cool. The handle should be placed on the handle holder.
  • A short power-supply cord is provided to reduce risks. If a longer detachable power-supply cord is used, ensure its electrical rating is at least as great as the appliance's, it is a grounding type 3-wire cord, and it is arranged to prevent tripping or snagging.
  • If the brass wool tip cleaner contains solid-state rosin: This product contains rosin (colophony), which may cause an allergic skin reaction. DO NOT inhale fumes or consume solid-state rosin. DO NOT allow skin and eyes to come into direct contact with rosin.

Product Overview

The Silverflo 938BD-III is a versatile 2-in-1 soldering and rework station designed for precision electronics work. It combines a T12 soldering iron with a hot air gun, offering rapid heating, digital temperature control, and various safety and efficiency features.

Silverflo 938BD-III Soldering Station with hot air gun, soldering iron, and accessories
Figure 1: Silverflo 938BD-III Soldering and Rework Station with included components.
Video 1: Product demonstration of the Silverflo 938BD-III station's features and use.

Applications

  • This unit is suitable for desoldering & soldering operations on a broad range of components, including SOIC, CHIP, QFP, PLCC, BGA, SMD, and more. It is especially suited for desoldering operations on in-line sockets.
  • You can use this unit for heat shrinking, drying, paint removal, glue removal, defrosting, pre-heating, glue soldering, and more.

Specifications

ParameterValue
Model Number938BD-III
Rated Power775W
DisplayLED
Main Unit DimensionsL143 x W125 x H96mm ±5mm
Operating Ambient Temperature0~40°C (32°F~104°F)
Temperature Range (Hot Air Rework Station)100°C~480°C (212°F~896°F)
Air DeliveryBrushless fan with smooth air delivery
Air Volume (Measured at Exhaust)≤30L/min
Temperature Range (Soldering Station)200°C~480°C (392°F~896°F)
Soldering Tip to Ground Resistance<2 ohms
CertificationCE, FCC
OriginMainland China

Components and Features

Control Panel Guide

Diagram of the control panel with numbered labels
Figure 2: Control Panel Layout and Components.
  1. Temperature Display (Hot Air Rework Station)
  2. Temperature Increase Button (Hot Air Rework Station)
  3. Temperature Decrease Button (Hot Air Rework Station)
  4. Power Switch (Hot Air Rework Station)
  5. Air Volume Adjustment Dial
  6. Master Power Switch
  7. Receptacle (Soldering Iron)
  8. Power Switch (Soldering Station)
  9. Temperature Decrease Button (Soldering Station)
  10. Temperature Increase Button (Soldering Station)
  11. Temperature Display (Soldering Station)

Key Features

  • Rapid Heating: The soldering iron heats up quickly due to its integrated heating core, making it efficient for various tasks. (Applicable to original brand heating cores only).
    Image showing rapid heating of the soldering iron tip, melting solder quickly.
    Figure 3: Rapid heating capability of the soldering iron.
  • Auto Sleep Mode (10-Minute): The soldering iron automatically enters sleep mode after 10 minutes of no usage or movement. This feature prevents tip oxidation, extends tip lifespan, saves energy, and protects the environment.
    Soldering station display showing 'SLP' for sleep mode, with instructions to wake up the iron.
    Figure 4: Auto Sleep Mode activation and wake-up methods.
  • 2-in-1 Design: Combines a T12 soldering iron and a hot air gun station. The hot air gun automatically starts when picked up and enters standby when placed down.
  • Digital Temperature Calibration: Both the hot air gun and soldering iron can use this function to improve work efficiency and ensure accurate temperature control.
    Image illustrating the digital temperature calibration process with a multimeter.
    Figure 5: Digital Temperature Calibration process.
  • Multifunctional Soldering Iron Holder: Equipped with a metal cleaning ball and cleaning sponge, this holder can be installed on top of the machine to save space.
    Image showing the soldering iron holder with tip storage, metal cleaning ball, and cleaning sponge.
    Figure 6: Multifunctional Soldering Iron Holder.
  • Long Service Life Brushless Fan: Features safety and efficient auto start-stop technology with extremely low noise (45dB) and smooth air delivery (≤120L/min). The rotating wind tunnel ensures steady temperature and consistent heat output.
    Diagram showing the internal brushless fan of the hot air gun with specifications.
    Figure 7: Brushless fan design for quiet and efficient operation.

Setup Instructions

  1. Install the hot air gun holder and the desired hot air nozzle. Ensure the nozzle is installed correctly without brute force.
  2. Connect the soldering iron to its designated receptacle on the control panel.
  3. Connect the station to a properly grounded power socket.
  4. Press the master power switch to turn on the station.

Initial Soldering Tip Preparation

Upon the first use of a new soldering tip, set the temperature to 250°C (482°F). Once the iron is hot enough to melt solder, coat the tip with a layer of solder (rosin core solder is recommended). Then, set the temperature to your desired working temperature.

Operating Instructions

Digital Temperature Calibration

  1. Once the hot air rework station or soldering station reaches temperature stabilization, press and hold both the temperature increase and decrease buttons for approximately 2 seconds. The display will show "CAL" while alternating with the set temperature.
  2. Press the temperature increase or decrease button to enter the measured temperature value.
  3. Press and hold both the temperature increase and decrease buttons again to confirm. The system will automatically calibrate the temperature and exit the calibration interface.

Auto Sleep Mode (10-Minute)

The station automatically detects its own operation status. If no usage or movement is detected for longer than 10 minutes, the soldering iron will enter sleep mode. This helps prevent tip oxidation, extends tip lifespan, saves energy, and protects the environment.

To wake the soldering iron from sleep mode, you can:

  • Shake the soldering iron a few times.
  • Press any button on the soldering station's control panel.
  • Turn the power switch OFF, then ON again.

Soldering Station Usage

  • If a layer of oxidation forms on the surface of the soldering iron tip, it may appear that the tip cannot heat up properly. To clean an oxidized tip: Set the temperature to 300°C (572°F). Once stable, gently rub the soldering iron tip inside the metal wool ball. As oxidation is removed, apply solder onto the tip while rubbing until the solder completely adheres. If the tip is severely oxidized, replace it.
  • DO NOT use metal files to remove oxidation from the soldering iron tip. Replace deformed or rusted tips.
  • DO NOT apply excessive force when soldering, as this can damage the iron tip and reduce heat transfer.
  • When placing the soldering iron in its holder after high-temperature operation, adjust the temperature to 250°C (482°F) or below for idling. This prevents accelerated aging of the heating element and extends its lifespan.
  • Always clean the soldering iron tip and coat it with solder after each operation to prevent oxidation.

Hot Air Rework Station Usage

  • Select the appropriate nozzle based on your operation requirements. Note that temperature may vary with different nozzle diameters. When using smaller nozzles than standard, use maximum air volume with a relatively lower temperature setting. Complete the operation in the shortest possible duration to avoid damaging the hot air gun.
  • Maintain a minimum distance of 2mm between the object and the hot air gun's air outlet.

Maintenance and Precautions

Hot Air Rework Station

  • Keep the air outlet clear and free of blockages at all times.
  • The installation of hot air gun nozzles MUST be carried out ONLY when the steel pipe and nozzle have cooled. Install the nozzle correctly; DO NOT install the nozzle with brute force, pull the edge of the nozzle with tweezers, or over-tighten the screws.
  • DO NOT allow the hot air to come in direct contact with facial parts, and beware of the danger of burn injuries.
  • Upon the first use, the hot air gun may emit white fumes, which will dissipate in a short while.

General Maintenance

  • Regularly clean the soldering iron holder and ensure the cleaning sponge is damp for effective tip cleaning.
  • Inspect all cables and connections for damage before and after each use.
  • Store the unit in a dry, clean environment when not in use.

Troubleshooting Guide

  • S-E Error: This indicates a fault in the station's sensor module, requiring replacement of the heating element (heating element and sensor modules). Alternatively, it may mean the soldering iron is not connected. Turn off the power, connect the soldering iron handle, then turn the station on again.
  • F-1/F-2 Error: This indicates that the hot air gun is in zero-air protection mode. The hot air gun and its power circuitry require inspection.
  • F-3 Error: This indicates that the input voltage is too low. To resume use, turn up the air volume, turn off the power switch, and then turn it on.
  • F-4 Error: This indicates that the input voltage is too high. To resume use, turn down the air volume, turn off the power switch, and then turn it on.
  • Heating Element Replacement: When replacing the heating element, take note of the original connecting order and colors of the wires, which MUST NOT be connected incorrectly.
  • SLP Display: This indicates that the sleep mode is active.

User Tips

  • Always keep your soldering iron tip tinned (coated with a thin layer of solder) when not in use to prevent oxidation and prolong its life.
  • Utilize the auto-sleep function to conserve energy and maintain tip health during breaks in work.
  • For delicate components, use the hot air gun with appropriate nozzle size and air volume to prevent damage.
  • Regularly check the soldering iron tips for wear and replace them when they become pitted or excessively oxidized, as this affects heat transfer efficiency.
  • Ensure your workspace is well-ventilated, especially when soldering, to avoid inhaling fumes.

Documents and Support

For a detailed PDF version of this user manual, please refer to the official document: Silverflo 938BD-III User Manual (PDF).


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.