AOVOPRO TX01 Smart APP Electric Scooter User Manual

Important Safety Information

WARNING: READ BEFORE USE

Riding an electric scooter can be a dangerous activity. Certain conditions may cause components to fail without fault of the manufacturer. The scooter can and is intended to move and it is therefore possible to lose control, fall off and/or get into dangerous situations that no amount of care, instruction or expertise can eliminate. If such a thing does occur you can become seriously injured or die, even when using safety equipment and other safety precautions.

RIDE AT YOUR OWN RISK AND ALWAYS USE COMMON SENSE.

This manual contains many warnings and cautions concerning the consequences of failing to inspect, maintain or properly use your electric scooter. Since any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death each time such a possibility is mentioned in this manual.

Appropriate Riding Attire

Always wear proper protective equipment such as:

• Approved safety helmet. (Helmet may be legally required by local law or regulation in your area.)
• Elbow pads and knee pads
• Long sleeved shirt, long pants
• Gloves
• Lace up shoes with rubber soles, never ride barefooted or in sandals, and ensure that shoelaces are tied and kept out of the way of the wheels and drive system.

Rider Use and Parental Supervision

RIDER MUST NOT EXCEED THE WEIGHT LIMIT OF 120 KG.

Rider weight does not always mean a person's size is appropriate to fit or maintain control of the scooter.

The recommended rider age is 16 years and older. Any rider that is unable to fit comfortably on the scooter should never attempt to ride it. A parent's decision to allow their child to use scooter should be based on the child's maturity, skill and their ability to follow rules.

Do not touch the motor or brakes on the scooter when in use or directly after use as these parts can become extremely hot.

Keep this scooter away from small children and remember that it is intended for use only by persons who are, at a minimum, completely competent and comfortable while operating this product.

Disclaimer:

Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

For detailed item guides and documents, please refer to the User Manual (PDF) available here.

Product Overview

The AOVOPRO TX01 Smart APP Electric Scooter is designed for efficient and comfortable urban travel. Below is an overview of its main components.

• Headlight: For illumination during low-light conditions.
• Brake Handle: Controls the braking system.
• Accelerator: Controls the scooter's speed.
• Display: Shows speed, battery level, and other operational information.
• Folding Mechanism: Allows the scooter to be folded for portability and storage.
• Clamp: Secures the handlebar post.
• Brake Light: Rear light for visibility and braking indication.
• Wheel Motor: Provides power for propulsion.
• Charging Port: For connecting the charger to replenish the battery.
• Drum Brake: Part of the dual braking system.
• Stand: For parking the scooter upright.

Assembly

Follow these steps to assemble your AOVOPRO TX01 Electric Scooter:

1. Connect the electric clips and fix the steering rod.
2. Set the handle bars vertical.
3. Open and lock the folding mechanism in place.

4. Using the included hex wrench and screws found in the accessories bag, tighten the screws on the handle bar. Remember to check and retighten every now and then.
5. Test turning the electric scooter on/off by holding down the power button for 3 seconds after assembly is complete.

Folding the Scooter

To fold your scooter for storage or transport, follow these instructions:

1. Ensure the scooter is switched off.
2. Hold the front pole and lean it slightly forward, then loosen the lock lever on the folding mechanism and lower the handlebars backwards towards the rear of the scooter.
3. Locate the rubber clamp located on the rear mud guard. The hook attached to the bell needs to latch on to the rubber clamp on the rear mud guard.
4. When you are ready to ride the scooter again, release the hook from the rubber clamp and lift the front pole to the upright position and lock the lever on the folding mechanism.

Battery and Charger

Proper battery care and charging are essential for the longevity and performance of your scooter.

Charging Instructions

• Charge the battery fully before use.
• The battery can be charged at any time to ensure it has power.
• Charge the battery once every three months to maintain its lifespan and charge level. The lithium battery can be recharged at least 500 times.
• The charger has a charging protection function; when the battery is 100% charged, the charger will automatically stop charging.
• The first initial charge is 6 hours. Each subsequent charge time is no more than 5 hours.
• To charge the scooter, open the rubber charging hole protective cover. Connect the charge connection into the charging hole.
• Connect the charger's plug into a power point.
• When the charger light is red, the battery is charging. When the charger light is green, the battery is fully charged.
• The charger should be regularly examined for damage to the cord, plug, enclosure and other parts. In the event of such damage, if any is found, the scooter should not be charged until the charger has been repaired or replaced.
• Use only with the supplied recommended charger. Always use caution when charging.
• The charger is not a toy and should be operated by an adult. Never operate charger near flammable materials or liquids. Disconnect the charger and unplug from scooter when not in use. Do not exceed recommended charging time.
• Always disconnect the charger from the scooter prior to wiping down cleaning.

Battery Care and Disposal

Do not store the battery in temperatures above 21°C (70°F) or below 0°C (32°F).

THIS SCOOTER CONTAINS SEALED LITHIUM BATTERIES WHICH MUST BE RECYCLED IN ACCORDANCE TO YOUR LOCAL AND STATE LAWS. PLEASE CAREFULLY READ AND UNDERSTAND THE FOLLOWING DISPOSAL INSTRUCTIONS:

Disposal: This product contains sealed lithium batteries which must be disposed or recycled in an environmentally safe manner. Do not dispose of the batteries in your household trash. Do not dispose of the batteries in a fire, this could cause the batteries to leak or explode. The incineration, disposal in landfill and or placing sealed lead acid batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a state or federal approved lead acid battery recycler or check with your local retailer of vehicle batteries.

WARNING: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

Operation

Control Panel Introduction

• Power Mode: Indicates the current riding mode (e.g., ECO, COMFORT, SPORT).
• Speed: Displays current speed.
• Bluetooth Connection: Light turns on when Bluetooth is connected to the app.
• Battery Power: Shows remaining battery charge.
• Speed Unit: Indicates speed unit (Km/h or mph).
• Cruise: Light turns on when cruise control is activated.

ON/OFF Button Functions:

• Press for 3 seconds to open/close the scooter.
• Short press to turn the headlight on/off.
• Short press twice to switch power mode.

APP Download and Functions

The AOVOPRO APP enhances your scooter experience with smart controls and data tracking.

1. Search for the 'Vicont' app in your device's APP store or Google Play.
2. Download and install the app onto your smart device.
3. Ensure Bluetooth is turned on. If using an Android phone, please agree to positioning authorization for the app.
4. Open the Vicont app, press the on/off button for 2 seconds to turn on the scooter, then you can search for scooter equipment in the app and connect it.
5. If you do not want to use the app, you can also use controls on the scooter to operate it.

Dashboard Operation Introduction (via APP)

The main operation interface shows:

• Current speed, Motor speed, Current value, Riding time, Current mileage, Total mileage.
• Gear switching: ECO (max speed 8mph), COMFORT (max speed 11mph), SPORT (max speed 19mph).
• Distance unit switch: km/h/mph.
• Controller temperature, Motor temperature, Battery temperature.
• Maximum speed, Current gear position, Lock status.

Custom Parameter Settings (via APP)

Click "Vehicle Setup" in the app to access custom settings:

• Maximum speed setting: Set the speed limit for your scooter.
• Setting of starting torque: Affects the scooter's starting power.
• Driving maximum torque setting: Affects the scooter's ability to climb hills.
• Electromagnetic brake strength setting: Adjusts electronic brake force (if applicable).

Emergency SOS Setting (via APP)

You can bind your emergency contact phone number here, so you can call for help with one click when needed.

Riding Operation

The scooter's highest speed setting is 31 Km/H. This may need to be adjusted in the Tuya smart app.

For your safety, please limit the speed within 0 - 20 Km/H. At night, it is recommended to limit the speed to 15 km/H or less and use the LED headlight. Choose a suitable venue for riding.

Start

1. Press the on/off button to turn on the power.
2. Stand one foot on the scooter and leave another foot on the ground.
3. Gently press down on the speed lever, the scooter will immediately move forward slowly. Place the foot which is on the ground on the scooter.
4. With the big finger of your right hand, press the speed lever; the greater pressure you put, the faster it will go.

Brake

Under normal circumstances, pressing the brake handle will immediately de-energize the scooter and activate the brake. The greater pressure you add, the greater braking force will be.

Cruise Control

Using the app, ensure that cruise control is ON. You can set up the speed as you want during the ride, and the scooter will start moving at the same speed afterwards. Press the speed lever and keep the same speed for 15 seconds. The scooter will make a beep sound and cruise control will automatically enter operation. You can stop cruise control by pressing on the speed lever once.

Start Mode

This function is for safety. In the Tuya smart app, if start mode is on, then pressing the accelerator will turn the scooter motor wheel. If start mode is off, you need to press the accelerator while kicking the scooter to make the motor wheel turn.

Hardware Maintenance

Regular maintenance ensures the safety and longevity of your electric scooter.

Brake

Check the brakes for proper function. When you squeeze the lever, the brake should provide positive braking action. When you apply the brake with the speed control on, the brake cut off switch should stop the motor. Make sure that the brakes are not rubbing.

Frame, Fork and Handlebars

Check for cracks or broken connections. Although broken frames are rare, it is possible for aggressive riders to run into a curb or wall and bend or break a frame. Get in the habit of inspecting your scooter on a regular basis.

Battery

Make sure the power switch is turned off whenever the scooter is not in use. Never store the product in freezing or below freezing temperatures! Freezing will permanently damage the battery.

Lubricating

Please add a small amount of grease or lubricants to the folded position every six months. Please check the scooter every three months to ensure screws are not loose.

Placement and Daily Care

Do not expose the scooter to direct sun or wet places for too long. Please keep the scooter clean and dry. For cleaning, use a damp cloth and mild detergent.

Charger

Only use the supplied battery charger. If the charger is damaged, discontinue use immediately and replace with a recommended charger.

Wheels

Wheels and drive system components are subject to normal wear and tear. It is the responsibility of the user to regularly inspect wheels for excess wear and adjust and replace drive train components as required.

Troubleshooting

Refer to the table below for common issues and their solutions:

General Troubleshooting

1. LED display black screen
   Reason: Exposure under the sun for too long.
   Solution: Place it in shadow and it will return to normal after a period.
2. No information on digital display
   Reason: Bad battery contacts or the battery is dead.
   Solution: Turn off the power then restart again, if the problem still occurs, please contact your local battery reseller.

Specifications

The AOVOPRO TX01 Electric Scooter comes in various configurations. Please refer to the table below for detailed specifications:

Disclaimer:

The mentioned speeds and distance are based on factory conditions. They may vary on a range of factors which include the weight of the rider, the speed of the ride and the incline of the ride.

User Tips

• Local Regulations: Always check and abide by local laws and regulations regarding electric scooters. In some regions (e.g., Germany), these scooters may not be street legal or insurable due to lack of specific certifications (like ABE).
• Charging Issues: If your scooter is not charging, first ensure the charger is properly connected to both the wall outlet and the scooter. If the problem persists, check the charger for damage or contact your battery reseller.
• Speed Settings: The maximum speed can often be adjusted via the companion app (e.g., Vicont or AOVOPRO APP) in the advanced settings.
• Tire Type: The scooter may come with either pneumatic or solid tires. Solid tires are explosion-proof and low maintenance, while pneumatic tires offer better shock absorption.

Warranty and Support

Our electric scooters come with a one-year warranty. If you encounter any questions or problems with your product, please do not hesitate to contact our customer service online. We are committed to providing quick responses and assistance to resolve any issues you may have.

For return and refund policies, please refer to the specific terms provided at the time of purchase or contact customer support.