GLEDOPTO ZigBee 3.0 ON OFF Relay Switch GL-C-310P Instruction Manual

Introduction

The GLEDOPTO ZigBee 3.0 ON OFF Relay Switch (Model GL-C-310P) is a compact and versatile device designed to integrate your existing electrical appliances into a smart home system. It supports both ZigBee 3.0 and 2.4G RF protocols, allowing for control via smartphone apps, voice commands, and dedicated RF remote controls. This manual provides essential information for the safe and efficient use of your relay switch.

Figure 1: Gledopto ZigBee Relay Switch GL-C-310P, highlighting its low standby power consumption (<0.5W).

Setup

1. Prerequisites

• A compatible ZigBee gateway (e.g., Hue, Alexa, Tuya, Homey) is required for ZigBee functionality (APP control, voice control).
• If a ZigBee gateway is not available, a GLEDOPTO 2.4G RF remote control or wall switch can be used for local control with Plus/Pro Version Products. Note that 2.4G RF devices are not ZigBee.

2. Wiring Instructions

The relay switch features quick connect ports for simplified wiring. Ensure power is disconnected before proceeding with any wiring.

1. Open the connector: Gently lift the connector tab upwards.
2. Insert the wire: Insert the stripped wire (8-9mm preparation, 0.5-1.63mm² / 24-14AWG) into the port.
3. Secure the wire: Press down the connector tab to secure the wire.

Figure 2: Quick connect port design, illustrating the steps for opening, inserting, and securing wires.

Refer to the wiring diagrams below for connecting the relay switch to your power supply and load. The device supports versatile input voltages.

Figure 3: Detailed wiring diagrams for AC 100-240V, DC 24-48V, and DC 12V power supplies. Includes a legend for device terminals and wire types.

Wiring Legend:

• Device Terminals:
  • I: Relay output terminal
  • O: Relay input terminal
  • SW: Switch input terminal
  • L: Live (100-240 VAC) terminal
  • N: Neutral terminal
  • 12V: DC positive terminal (12V stabilized)
  • -: DC ground terminal
  • +: DC positive terminal (24-48V)
• Wires:
  • N: Neutral wire
  • L: Live (100-240 VAC) wire
  • GND: DC ground wire
  • DC+: DC positive wire (24-48V)
  • 12V+: Positive wire (12V stabilized)

3. Pairing with a ZigBee Gateway

Once wired, follow your ZigBee gateway's instructions to add a new device. The GLEDOPTO relay switch is compatible with ZigBee 3.0 gateways from brands like Hue, Alexa, Tuya, and SmartThings. The device will typically enter pairing mode automatically upon first power-up or after a reset.

Figure 4: Indicator light status. Flashing indicates a push switch is connected, while steady on indicates a rocker switch.

Operating Instructions

1. Basic On/Off Control

The relay switch can be controlled via a connected physical switch (push or rocker type) or through your smart home system.

2. App Control

Once paired with a ZigBee gateway, you can control connected devices using the corresponding smartphone application (e.g., Tuya Smart Life app). This allows you to turn devices on/off from anywhere.

Figure 5: The relay switch integrated with a push switch and controlled via a smartphone app, compatible with ZigBee 3.0 gateways.

3. Voice Control

For ZigBee-enabled setups, the switch supports voice control through compatible smart assistants like Amazon Alexa or Google Assistant, once integrated with your ZigBee hub.

Figure 6: Voice control functionality demonstrated with Amazon Echo Plus, alongside smartphone app control.

4. 2.4G RF Remote Control (Optional)

If you have a GLEDOPTO 2.4G RF remote control (e.g., GL-RC-002, GL-RC-006, GL-RC-007, GL-RC-009, GL-W-003Z), you can pair it directly with the relay switch for local wireless control, especially useful for Plus/Pro Version Products without a ZigBee gateway.

Figure 7: The Gledopto ZigBee Relay Switch showing compatibility with various 2.4G RF remote controls.

5. Power-off Memory Function

The device offers two optional modes for its power-off memory function:

• Lights up by default when powered on: The device will turn on automatically after a power failure.
• Remember the state of the on/off before power failure: The device will return to its last known state (on or off) after a power failure.

To enable/disable this function, long press the "On/Off" key for more than 5 seconds. The connected device will turn on and off twice, indicating activation of this function.

Figure 8: Illustration of the power-off memory function, showing options to default to 'on' or remember the last state.

6. Reset Functionality

The device has two reset functions:

• Short Press: Changes the connection type between a push switch and a rocker switch.
• Long Press (5 seconds or more): Resets the relay switch to factory settings, which can be used for re-pairing or troubleshooting.

Figure 9: Diagram detailing the short press and long press functions for On/Off and Reset buttons.

Maintenance

• Keep the device dry and away from moisture.
• Clean the exterior with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
• The casing is made of fireproof PC material for enhanced safety.
• Operating temperature range is -20°C to 60°C. Avoid exposing the device to extreme temperatures.

Figure 10: Image highlighting the fireproof PC material used in the construction of the relay switch for increased safety.

Troubleshooting

• Device not responding: Check all wiring connections to ensure they are secure. Verify the power supply is active.
• Cannot pair with ZigBee gateway: Ensure the gateway is powered on and within range. Try resetting the relay switch (long press Reset button for 5+ seconds) and re-initiating the pairing process on your gateway.
• Indicator light behavior: Refer to Figure 4 for expected indicator light status (flashing for push switch, steady on for rocker switch). Unexpected behavior may indicate a wiring issue or incorrect switch type setting.
• Intermittent connectivity: Ensure the ZigBee gateway is centrally located and not obstructed by large metal objects. Consider the number of ZigBee devices in your network; ZigBee 3.0 supports more connections for better network stability.

Specifications

Figure 11: Detailed product parameters for the Gledopto Zigbee Relay Switch GL-C-310P.

Warranty & Support

For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact your retailer or the GLEDOPTO customer support directly. Keep your purchase receipt for warranty claims.

User Tips

• ZigBee Advantages: The ZigBee 3.0 protocol offers several benefits over Wi-Fi and Bluetooth, including lower power consumption, higher stability, stronger anti-interference capabilities, and enhanced security and privacy. It also supports a larger number of connected devices (50+ pcs) in a single network.

Figure 12: Comparison of wireless protocols, highlighting the benefits of Zigbee 3.0 in terms of power, stability, anti-interference, security, and number of connections.

• Smart Home Integration: To fully utilize the smart features like APP control and voice commands, ensure your ZigBee gateway is properly set up and connected to your home network.
• Energy Efficiency: With ultra-low standby power consumption (<0.5W), this relay switch is designed to be energy-saving and environmentally friendly.
• Versatile Applications: The switch can make various household electric appliances smarter, including fans, kettles, light bulbs, ovens, and air purifiers.

Figure 13: The Gledopto relay switch can be used to smarten a variety of household appliances.

• High-Quality Components: The switch uses high-quality SanYou relays, ensuring durability and reliable performance even with high-power appliances.

Figure 14: Internal view highlighting the high-quality SanYou relay, designed for reliable performance with high-power appliances.

• Compact Design: Its ultra-mini size (42x38x17mm) and lightweight design (28.7g) allow for discreet installation in various scenarios, saving space and maintaining aesthetics.

Figure 15: Image demonstrating the compact dimensions and light weight of the relay switch, suitable for various installation environments.