1. Introduction
The Flysky FS-R11P is a high-performance 11-channel bidirectional receiver designed for remote control model cars and ships. It utilizes the advanced ANT communication protocol, offering reliable signal transmission and reception. This receiver features an external single coaxial antenna and supports multiple data output formats including PWM, PPM, i-BUS, and S-BUS, making it versatile for various RC applications.
Figure 1: Overview of the Flysky FS-R11P Receiver.
2. Package Contents
- 1x Flysky FS-R11P 11-Channel Receiver
- Instruction Manual (this document)
Figure 2: FS-R11P Receiver in its packaging.
3. Setup
3.1 Component Identification
Figure 3: Top view of the FS-R11P receiver, showing LED, BIND button, and servo ports 7-11.
Figure 4: Side view of the FS-R11P receiver, showing VCC, BVD, and BIND pins for channels 1-6.
- LED Indicator: Shows the status of the receiver (e.g., power, binding status).
- BIND Button: Used to initiate the binding process with a compatible transmitter.
- Servo Ports (1-11): Connect your servos, ESCs, and other accessories. Channels 1-6 are on one side, and 7-11 are on the other.
- VCC/BVD Pins: Power input and Battery Voltage Detection.
- Antenna: External single coaxial antenna for signal reception. Ensure it is properly extended and positioned for optimal range.
3.2 Power Connection
The receiver operates on a voltage range of 3.5-9V DC. Connect your power source (e.g., ESC BEC, separate battery) to the VCC pins or any available servo channel's power pins, ensuring correct polarity.
3.3 Binding Procedure
To establish communication between the FS-R11P receiver and your Flysky FS-G11P (or other compatible ANT protocol transmitter), follow these steps:
- Ensure your transmitter is powered off.
- Connect a bind plug (if required by your transmitter/receiver combination, though the FS-R11P has a dedicated BIND button) or hold down the BIND button on the FS-R11P receiver.
- Apply power to the receiver (3.5-9V DC). The LED on the receiver should start flashing rapidly, indicating it's in bind mode.
- While still holding the BIND button (if applicable), power on your transmitter and put it into bind mode (refer to your transmitter's manual for specific instructions).
- Once binding is successful, the LED on the receiver will stop flashing and remain solid.
- Release the BIND button (if applicable) and power off both the receiver and transmitter.
- Power on the transmitter first, then the receiver. The receiver's LED should illuminate solid, indicating a successful connection.
Note: The FS-R11P is compatible with transmitters supporting the ANT protocol, such as the Flysky FS-G11P.
4. Operating the Receiver
Once successfully bound to your transmitter, the FS-R11P receiver will translate your transmitter's commands into signals for your model's components.
- Channel Allocation: The receiver provides 11 channels. Connect your servos, Electronic Speed Controllers (ESCs), and other accessories to the corresponding PWM ports (1-11) as per your model's requirements.
- Data Output: The receiver supports PWM, PPM, i-BUS, and S-BUS data output. Ensure your connected devices are compatible with the selected output mode.
- Antenna Placement: For optimal range and signal integrity, ensure the external coaxial antenna is positioned away from metal objects and other electronics that might cause interference. Avoid bending or cutting the antenna wire.
- Remote Control Distance: The effective remote control distance is ≥ 300m in open and undisturbed ground conditions. Factors like obstacles, interference, and antenna placement can affect this range.
5. Maintenance
- Cleaning: Keep the receiver clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning.
- Storage: Store the receiver in a dry, cool environment, away from direct sunlight and extreme temperatures.
- Antenna Inspection: Regularly check the antenna for any damage, kinks, or fraying. A damaged antenna can significantly reduce range and reliability.
- Connection Check: Periodically inspect all connections to ensure they are secure and free from corrosion.
- Firmware: The receiver supports firmware updates. Check the official Flysky website for any available updates and follow their instructions carefully.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Receiver LED not lighting up. | No power or incorrect power connection. | Check power source (3.5-9V DC) and ensure correct polarity. |
| Receiver LED flashing rapidly. | Receiver is in bind mode but not yet bound. | Complete the binding procedure with your transmitter. |
| No response from model after binding. | Incorrect binding, incompatible transmitter, or servo/ESC not connected properly. | Re-bind the receiver. Ensure your transmitter supports ANT protocol. Check all servo/ESC connections and their functionality. |
| Reduced range or intermittent signal. | Antenna obstruction/damage, environmental interference, low transmitter/receiver battery. | Ensure antenna is clear and undamaged. Avoid operating near large metal objects or strong RF sources. Check battery levels. |
7. Specifications
Figure 5: Detailed specifications of the FS-R11P Receiver.
| Feature | Detail |
|---|---|
| Product Model | FS-R11P |
| Compatible Transmitter | FS-G11P (transmitter supporting ANT protocol) |
| Adaptation Models | Cars, Ships |
| PWM Channel | 11 |
| Wireless Frequency | 2.4GHz ISM |
| Transmission Power | < 20dBm |
| Antenna Type | External single antenna (coaxial) |
| Remote Control Distance | ≥ 300m (open and undisturbed ground distance) |
| Wireless Protocol | ANT (Ant Version Automatic Frequency Hopping Digital System) |
| Channel Resolution | 4096 levels |
| Data Output | PWM/PPM/i-BUS/S-BUS |
| Working Voltage | 3.5-9V/DC |
| Firmware Update | Supports |
| Temperature Range | -10°C ~ 60°C |
| Humidity Range | 20% ~ 95% |
| Waterproof Grade | PPX4 |
| Dimensions | 37.0mm * 25.0mm * 13.3mm |
| Body Weight | 10g |
| Authentication | CE, FCCID:2A2UNR11P00 |
8. Warranty and Support
For warranty claims, technical support, or further assistance, please contact the seller or the official Flysky support channels. Keep your purchase receipt as proof of purchase.
9. User Tips
- Always perform a range check before operating your model, especially in new environments.
- Ensure all connections are secure to prevent signal loss during operation.
- Consider using a failsafe setup on your transmitter to prevent runaway models in case of signal loss.
- Keep the receiver away from high-current wires and motors to minimize electrical interference.