HOBBYEAGLE A3 Super 4

Contents

HOBBYEAGLE A3 Super 4 RC Plane Airplane Gyro Flight Controller Stabilizer User Manual

Model: A3 Super 4

Brand: HOBBYEAGLE

Introduction

The HOBBYEAGLE A3 Super 4 is a high-performance, powerful 6-axis gyroscope and balancer designed specifically for fixed-wing model aircraft. Featuring a 32-bit processor and high-precision MEMS 6-axis sensor, it offers enhanced reliability and user-friendly operation. This manual provides essential information for setting up, operating, and maintaining your A3 Super 4 flight controller.

Package Contents

Please verify that all items are present in your package:

  • 1 x A3 Super 4 Main Controller
  • 1 x Program Card
  • 1 x LED module
  • 3 x Receiver Cables
  • 1 x Data Cable
  • 1 x Adapter
  • 2 x Double-sided Tapes
Contents of the A3 Super 4 Standard package, including the main controller, cables, and accessories.
Figure 1: A3 Super 4 Standard package contents.
HOBBYEAGLE A3 Super 4 Gyro Flight Controller and included accessories (cables, adapter, double-sided tapes).
Figure 2: HOBBYEAGLE A3 Super 4 Gyro Flight Controller and accessories.

Specifications

FeatureSpecification
Main Controller32-bit microprocessor
Built-in SensorsHigh-precision MEMS 6-axis sensor
Gyro Range± 2000 dps
Acceleration Range± 4g
PWM Output800 ~ 2220uS, median 1500/1520uS, frequency 50Hz ~ 333Hz
Working VoltageDC 4.8V ~ 8.4V
Working Temperature-10℃ ~ 50℃
Dimensions (L×W×H)43×27×14mm
Weight (without cable)10g

Setup

Wiring Diagram

Refer to the diagram below for proper connection of the A3 Super 4 gyro to your receiver, Electronic Speed Controller (ESC), and servos. Ensure all connections are secure and correctly oriented.

Detailed wiring diagram illustrating connections between the receiver, A3 Super 4 gyro, ESC, and various servos (Elevator 2, Aileron 2, Rudder, Elevator, Aileron). Note: Pins marked 'Top' are signal input only, not power supply.
Figure 3: A3 Super 4 Wiring Diagram. Note: Pins labeled 'Top' are for signal input only and should NEVER be used as a power supply.

Initial Configuration

The A3 Super 4 supports various receiver types and configurations:

  • PWM Receiver: Connect individual channels from your receiver to the corresponding input pins on the A3 Super 4.
  • PPM and Multi-protocol Digital Serial Receivers: The unit offers full support for these types, including:
    • FrSky SBus
    • JETI SBus
    • RadioLink SBus
    • WFLY WBus
    • Spektrum DSM2/X 1024 Satellite Receiver
    • Spektrum DSM2/X 2048 Satellite Receiver
    • Spektrum SRXL
    • Multiplex SRXL / JR XBUS Mode B
    • Graupner SUMD
    • FlySky iBus
    • JETI EXBus

Use the provided Program Card for detailed parameter adjustments and firmware upgrades. The flexible configurable output interface provides 2 direct output channels.

HOBBYEAGLE A3 Super 4 Gyro Flight Controller alongside the Program Card and connection cables.
Figure 4: A3 Super 4 with Program Card.

Operating Modes

The A3 Super 4 features 6 distinct flight modes and 6-stage mode switching for versatile flight control:

  • Gyro Off Mode: Disables the gyroscope for direct control.
  • Normal Stabilization Mode: Provides basic stabilization, assisting with level flight.
  • Lock Mode: Locks the aircraft's attitude, maintaining its current orientation.
  • Angle Mode: Limits the maximum bank and pitch angles, ideal for beginners.
  • Balance Mode: Automatically levels the aircraft when control sticks are centered.
  • Hoist Mode: Specific mode for vertical ascent/descent control.

Remote overall gain adjustment is supported, allowing fine-tuning of stabilization sensitivity during flight.

User Tips

  • When using a serial bus receiver, the A3 Super 4 can effectively manage multiple servos (e.g., dual ailerons, dual elevators, CDI, choke) even with a receiver that has fewer physical channels. This optimizes wiring and simplifies setup.
  • Utilize the Program Card for precise parameter adjustments to match your aircraft's characteristics and flying style.
  • Regularly check for firmware updates to ensure optimal performance and access to new features.

Troubleshooting

  • No response from controls: Check all wiring connections between the receiver, gyro, and servos. Ensure the receiver is powered and bound to your transmitter.
  • Unstable flight: Verify that the gyro is mounted securely and oriented correctly. Adjust the overall gain settings using your remote control or the Program Card. Ensure servo directions are correctly set.
  • Incorrect servo movement: Confirm that the servo directions are properly configured in the A3 Super 4 settings via the Program Card.
  • Gyro not initializing: Ensure the unit receives stable power within the specified voltage range (DC 4.8V ~ 8.4V).

Maintenance

  • Keep the A3 Super 4 unit clean and free from dust and debris.
  • Avoid exposing the unit to extreme temperatures or moisture.
  • Ensure all cables are free from damage and securely connected before each flight.
  • Store the unit in a dry, cool place when not in use.

Warranty and Support

For warranty information, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.