EPEVER TracerAN G3 Series

Contents

EPEVER TracerAN G3 Series MPPT Solar Charge Controller User Manual

Models: Tracer1206AN G3, Tracer2206AN G3, and accessories

1. Introduction

The EPEVER TracerAN G3 Series MPPT Solar Charge Controller is an advanced maximum power point tracking (MPPT) controller designed for off-grid solar systems. It features an innovative MPPT algorithm and adaptive charging to maximize energy harvest from solar panels. This series is compatible with various battery types, including lithium batteries, and offers robust protection features. The G3 series can even operate without a battery connected, providing direct power to loads.

This manual provides detailed instructions for the installation, operation, and maintenance of your TracerAN G3 solar charge controller and its compatible accessories, including USB, WiFi, BLE communication modules, and remote meters like MT11, MT75, and MT50.

EPEVER TracerAN G3 Series MPPT Solar Charge Controller with MT52, WiFi, and BLE accessories
Figure 1: EPEVER TracerAN G3 Series MPPT Solar Charge Controller and accessories.

2. Product Features

  • Innovative MPPT Algorithm and Adaptive Charging: Ensures maximum power point tracking efficiency above 99.5% and conversion efficiency up to 98%.
  • Lithium Battery Compatibility: Supports various battery types including LI, AGM, GEL, SLD, and FLD, with auto-identification for 12V/24V battery voltage.
  • Battery Care and Constant Voltage Output: Designed for optimal battery health and stable power delivery.
  • Seamless Operation: Can be used without a battery, providing direct power to DC loads.
  • RS485 Communication: Enables connection to external devices for monitoring and parameter configuration.
  • Energy Efficient & Quiet: Optimized for low static losses and silent operation.
  • Durability & Protection: Features IP30 enclosure and robust design for various environmental conditions.
EPEVER TracerAN G3 Series MPPT Solar Charge Controller compatible with various battery types
Figure 2: TracerAN G3 compatibility with various battery types.

3. Setup & Installation

3.1. General System Overview

A typical solar power system includes solar panels, the MPPT charge controller, a battery system, and loads (which may be connected via an inverter for AC loads). Ensure all components are rated appropriately for your system's voltage and current requirements.

Diagram showing a typical solar power system setup with solar panels, MPPT controller, battery system, inverter, and loads
Figure 3: Typical Solar Power System Diagram.

3.2. Controller Wiring

Connect the solar panels, battery, and loads to the controller terminals as indicated on the device. Always connect the battery first, then the solar panels, and finally the loads. Ensure correct polarity for all connections. Refer to the specifications section for recommended wire sizes.

3.3. Accessory Installation

3.3.1. USB-RS485 Communication Cable (CC-USB-RS485-150U)

This cable allows connection between the solar charge controller and a PC for monitoring and parameter setting using EPEVER PC software.

USB-RS485 communication cable (CC-USB-RS485-150U)
Figure 4: USB-RS485 Communication Cable.

3.3.2. Temperature Sensor Cable (RTS300R47K3.81A)

Connect the temperature sensor to the designated port on the controller to enable accurate temperature compensation for battery charging.

Temperature sensor cable (RTS300R47K3.81A)
Figure 5: Temperature Sensor Cable.

3.3.3. Remote Meters (MT11, MT50, MT75)

These meters connect via the RS485 port to provide real-time monitoring and control of the solar charge controller. The MT52 is compatible with controllers featuring RS485 communication.

EPEVER MT52 Remote Meter
Figure 6: EPEVER MT52 Remote Meter.

3.3.4. WiFi Adapter (EPEVER WiFi 2.4G RJ45 D)

The WiFi 2.4G RJ45 D adapter allows wireless monitoring and parameter programming of your EPEVER solar controller, inverter, or inverter/charger via the EPEVER cloud server or mobile APP (Solar Guardian).

EPEVER WiFi 2.4G RJ45 D adapter overview, features, specifications, and working process
Figure 7: WiFi Adapter Overview and Connection.
WiFi Adapter Connection Steps (Solar Guardian App):
  1. Turn on the WiFi switch on your mobile phone and connect to a local WiFi network (2.4G WiFi network is a must).
  2. Login to the Solar Guardian APP and click the '+' icon to add a new gateway.
  3. Select the gateway model.
  4. Input the gateway data ("Gateway SN" is the 22-digit number of the gateway, "WiFi name", and click "Next Step" to enter the device adding page.
  5. After adding the device, click "Next Step" to enter the above page.
  6. Input the local WiFi password and click "Next Step."
  7. Click "Go to set up Wi-Fi" to connect phone to the gateway WiFi (HN_EPSN_xxxxxx), password (12345678). Return to the APP after connection, and click "Next Step."
  8. After the gateway is successfully connected, connect the phone to local WiFi or 4G that can access the Internet. You can then monitor the device through the APP.
Step-by-step guide for connecting the WiFi adapter to the Solar Guardian app
Figure 8: WiFi Adapter App Connection Process.

3.3.5. BLE Adapter (EPEVER BLE RJ45 D)

The EPEVER BLE RJ45 D Bluetooth module enables wireless communication and data collection for your EPEVER solar controller, inverter, or inverter/charger. It supports Bluetooth 5.0 and BLE technology, offering fast communication and strong anti-interference ability.

EPEVER BLE RJ45 D Bluetooth module
Figure 9: EPEVER BLE RJ45 D Bluetooth Module.
BLE Adapter Connection Steps (Solar Guardian App):
  1. Log in to the APP, click "Me > Data" and select all products. Then click "Data Sync" to download all data.
  2. Return to the APP home page, click the "Go Offline" in the upper-right corner (or log out of the APP), and click the "Enter Offline Mode" on the initial page.
  3. Select the module type (Bluetooth).
  4. Turn on your phone's Bluetooth switch and enable the "Bluetooth Configuration" to search the Bluetooth module automatically. Click the "Add" to connect the specified Bluetooth module.
  5. Return to the APP and click the "Device" icon to enter the "Device List" page. Click the "Add Device" or the '+' in the upper-right corner to jump to the device addition interface.
  6. Input the product name, select the product series, set the communication ID, and click "Confirm" to complete the device adding.
  7. Click the icon on the "Device List" page to modify the device information.
  8. On the "Device List" page, click the device icon to display the device configuration figure and real-time data. Click the '...' icon in the upper right corner to view the device overview and set parameters.
Step-by-step guide for connecting the BLE adapter to the Solar Guardian app
Figure 10: BLE Adapter App Connection Process.

Download the Solar Guardian App:

QR codes for downloading the Solar Guardian app from Apple App Store and Google Play
Figure 11: Solar Guardian App Download QR Codes.

3.3.6. eLOG01 Data Logger

The eLOG01 data logger records and downloads system data, compatible with PC software and MT50 for real-time monitoring. It connects to a PC via USB interfaces and is powered by the controller's communication interface. It has a record capacity of up to 20,000 points.

EPEVER eLOG01 data logger and communication cables
Figure 12: EPEVER eLOG01 Data Logger.
eLOG01 connection diagram and features
Figure 13: eLOG01 Connection Diagram and Features.

4. Operating Instructions

4.1. Controller Display and Buttons

The controller features an LCD display and buttons (SELECT, ENTER) for navigation and parameter adjustment. The display shows real-time system status, including charging current, battery voltage, and load status.

4.2. Load Working Modes (TracerAN G3)

The TracerAN G3 series offers six distinct load working modes:

  1. Manual Mode: Load can be manually turned ON/OFF.
  2. Light ON/OFF Mode: Load turns ON at dusk and OFF at dawn.
  3. Light ON/OFF + Timer Mode 1: Load turns ON at dusk and stays ON for a set duration.
  4. Light ON/OFF + Timer Mode 2: Load turns ON at dusk, stays ON for a set duration, turns OFF, and then turns ON again for another set duration before dawn.
  5. Real-time Control Mode: Load operation is controlled by real-time clock settings.
  6. Always ON Mode: Load is continuously ON.
Comparison of Tracer-AN and Tracer-AN G3 load working modes, showing Tracer-AN G3 supports six modes
Figure 14: TracerAN G3 Load Working Modes.

4.3. Remote Monitoring via App

Utilize the Solar Guardian app with either the WiFi or BLE adapter to remotely monitor your system's performance, view historical data, and adjust controller parameters from your smartphone or tablet.

5. Maintenance

Regular maintenance ensures optimal performance and longevity of your solar charge controller and system.

  • Inspect Connections: Periodically check all wiring connections for tightness and corrosion. Loose connections can cause overheating and power loss.
  • Clean Terminals: Ensure battery and solar panel terminals are clean and free of rust or dirt.
  • Environmental Check: Ensure the controller is installed in a dry, well-ventilated area, away from direct sunlight, high humidity, salt spray, corrosive gases, flammable materials, and excessive dust accumulation.
  • Firmware Updates: Check the EPEVER website or Solar Guardian app for any available firmware updates for your controller and communication modules.
  • Battery Health: Monitor battery voltage and health regularly, especially for lead-acid batteries, to ensure proper charging and discharge cycles.

6. Troubleshooting

If you encounter issues with your EPEVER TracerAN G3 series controller, refer to the following common troubleshooting tips:

  • No Power/Display: Check all power connections, especially from the battery. Ensure the battery voltage is within the controller's operating range.
  • No Charging: Verify solar panel connections and ensure they are receiving adequate sunlight. Check for any shading or damage to the panels. Confirm that the PV open-circuit voltage is within the controller's limits.
  • Load Not Working: Check load connections and ensure the load is not exceeding the controller's rated discharge current. Verify the selected load working mode.
  • App Connection Issues:
    • Ensure the WiFi/BLE adapter is correctly connected to the controller's RS485 port.
    • For WiFi, confirm your phone is connected to a 2.4G WiFi network during setup.
    • For BLE, ensure Bluetooth is enabled on your phone and the adapter is within range (up to 10 meters).
    • Controller Model Not Recognized in App: If your specific controller model (e.g., XTRA4415N) is not listed or recognized in the Solar Guardian app, ensure you have the latest version of the app. If the issue persists, contact EPEVER technical support for compatibility information or alternative configuration methods.
  • Error Codes: If the controller display shows an error code, consult the full product manual (if available) or EPEVER's support resources for specific interpretations and solutions.

7. Specifications

7.1. TracerAN G3 Series Controller Electrical Parameters

Parameter Tracer1206AN G3 Tracer2206AN G3 Tracer1210AN G3 Tracer2210AN G3 Tracer3210AN G3 Tracer4210AN G3
Electrical Parameters
Battery Rated Voltage 12/24VDC Auto-recognition①
Rated Charging Current 10A 20A 10A 20A 30A 40A
Rated Discharge Current 10A 20A 10A 20A 30A 40A
Controller Work Voltage Range 8~31V
PV Maximum Open-circuit Voltage 60V② / 46V③ 100V② / 92V③
MPPT Voltage Range (Battery voltage +2V)~36V (Battery voltage +2V)~72V
Rated Charging Power 130W/12V, 260W/24V 260W/12V, 520W/24V 130W/12V, 260W/24V 260W/12V, 520W/24V 390W/12V, 780W/24V 520W/12V, 1040W/24V
Static Losses ≤8mA(12V), ≤5mA(24V)
Discharge-circuit Voltage Drop ≤0.23V
Temperature Compensation④ -3mV/℃/2V (Default)
Grounding Type Common negative
RS485 Port 5VDC/200mA (RJ45)
LCD Backlight Time Default: 60S, Range: 0~999S (0 seconds: the backlight is ON all the time)
Environmental Parameters
Work Temperature Range⑤ -25℃~+45℃ (100% loads working)
Storage Temperature Range -20℃~+70℃
Relative Humidity <95% (N.C.)
Enclosure IP30
Dimension (LxWxH) 172x139x44mm 220x154x52mm 228x164x55mm 252x180x63mm
Mounting Size (LxW) 124x130mm 170x145mm 170x155mm 204x171mm
Mounting Hole Size φ5mm
Terminal 12AWG (4mm²) 6AWG (16mm²)
Recommended Wire Size 12AWG (4mm²) 10AWG (6mm²) 8AWG (10mm²) 6AWG (16mm²)
Net Weight 0.57kg 0.94kg 1.26kg 1.65kg

①When a lithium battery is used, the system voltage isn't automatically identified.
②At minimum operating environment temperature.
③At 25℃ environment temperature.
④When a lithium battery is used, the temperature compensation coefficient will be 0 and can't be changed.
⑤The controller can full load working in the working environment temperature. When the internal temperature reaches 81℃, the reducing charging power mode is turned on.

7.2. EPEVER WiFi 2.4G RJ45 D Adapter Specifications

Parameter EPEVER WiFi 2.4G RJ45 D
Working voltage 5V±0.0V (Powered by RS485 com. port)
Power consumption Peak emission: 150mA, Idle: 310uA
Enclosure IP30
Communication method RS485
Communication parameters 115200bps, 8N1
Interface standard EPEVER communication standard V1.0
Work frequency 2.4 ~ 2.4835GHz
Work temperature range -40 ~ 85℃
Dimension 63mm x 19mm x 10mm
Net weight 7.7g

Note: The WiFi adapter working voltage is 4.5V-5.5V and peak emission is 150mA, which is only suitable for devices that meet this requirement.

7.3. EPEVER BLE RJ45 D Adapter Technical Specifications

Parameter EPEVER-BLE-RJ45-A
Input voltage 5V±0.5V (Powered by RS485 com. port)
Power consumption Average: 5V@10mA; Peak: 5V@60mA
Communication distance ≤10m
Serial port baud rate 2400~115200bps (default 115200bps)
Communication method RS485 to Bluetooth
Connection port RJ45 port
Connection cable Standard network cable (parallel line)
Bluetooth protocol Bluetooth 5.0, compatible with Bluetooth 4.0
Dimension 51*67*24.5mm
Mounting dimension 41.2, φ3.2
Working temperature -20~70℃
Enclosure IP30
Net Weight 37.9g

8. Warranty & Support

EPEVER products are designed for reliability and performance. For warranty information, please refer to the official EPEVER warranty policy provided with your product packaging or visit the EPEVER official website. In case of any issues or technical inquiries, please contact EPEVER customer support directly.

9. User Tips

  • App Compatibility: If you experience difficulty configuring your specific controller model (e.g., XTRA4415N) within the Solar Guardian app, ensure you have downloaded the latest version of the app. If the model is still not recognized, it is recommended to contact EPEVER support for guidance on compatibility or alternative setup procedures.
  • Environmental Protection: To ensure the longevity and proper functioning of your communication modules (WiFi/BLE adapters), avoid installing them in environments with high humidity, salt spray, corrosive substances, or excessive dust.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.