EPEVER UP5000-HM8042

Contents

EPEVER UPower-Hi Series Hybrid Inverter Charger

Instruction Manual

Models: UP5000-HM8042, UP3000-HM10022

Brand: EPEVER

1. Overview

The EPEVER UPower-Hi series is an advanced inverter charger designed for diversified energy management in solar, utility, and generator hybrid systems. It efficiently handles charging from solar, utility, or generator sources and supplies AC loads from utility or inverter power. This system prioritizes solar energy utilization, allowing users to flexibly supplement power from the utility grid as needed. The UPower-Hi series enhances power supply reliability and stability, making it ideal for various off-grid and hybrid power applications.

EPEVER 5KW Hybrid Inverter Charger UP5000-HM8042
EPEVER 5KW Hybrid Inverter Charger UP5000-HM8042, highlighting 5KW, 48V to 220/230V, No-Battery support, 60A Max Utility Charging, 80A Max PV Charging.

What is an Inverter/Charger?

An Inverter/Charger, or Combined Inverter Charger, integrates a solar charge controller and an inverter into a single unit. This device converts DC power to AC power and AC power to DC power. This integration offers a cost-effective, efficient, and simplified solution for installation, commissioning, and maintenance in solar energy systems.

Diagram illustrating the function of an inverter charger
Conceptual diagram of an Inverter/Charger converting DC to AC and AC to DC.

2. Key Features

  • Flexible Operation: Supports both battery mode and non-battery mode configurations.
  • Enhanced Protection: Features surge current and reverse connection protections, ideal for lithium battery systems.
  • High MPPT Efficiency: Achieves a Maximum Power Point Tracking (MPPT) efficiency of no less than 99.5%.
  • PFC Technology: Utilizes Power Factor Correction (PFC) technology for high power factor AC to DC charging, reducing power grid capacity usage.
  • Pure Sine Wave Output: Advanced SPWM technology ensures a pure sine wave output for sensitive electronics.
  • Configurable Currents: Allows configuration of battery charging current, discharging current, and grid charging current.
  • Smart SOC Function: Incorporates a self-learning State of Charge (SOC) function for optimized battery management.
  • User-Friendly Display: Equipped with a 4.2-inch LCD for monitoring system parameters and making adjustments.
  • Remote Control Options: Offers optional WiFi and GPRS remote control capabilities via the RS485 isolated communication port.
  • BMS Integration: Includes a BMS-Link port and supports an optional BMS-Link communication protocol module for advanced battery management.

3. Applications

The EPEVER UPower-Hi series inverter charger is versatile and suitable for a wide range of applications, providing reliable power in various scenarios:

  • Residential: Solar Home systems for household appliances like TVs, refrigerators, computers, microwave ovens, and dishwashers.
  • Mobile & Portable: Ideal for Solar Boats, Solar Cars, and Portable Solar Power Generators.
  • Off-Grid Systems: Provides stable power where grid access is limited or unavailable.
  • Backup Power: Can be integrated into systems requiring backup power from batteries or generators.
Diagram showing various applications of the inverter charger
Illustrative examples of inverter charger applications, including solar homes, boats, cars, and powering common household appliances.

4. Product Components and Identification

Familiarize yourself with the various parts and interfaces of your EPEVER UPower-Hi series inverter charger for proper installation and operation.

Diagram of inverter charger components from multiple angles
Views of the inverter charger showing various components and connection points.

Part Identification Table

Table identifying numbered parts of the inverter charger
Detailed identification of each numbered component on the inverter charger.
No.Item
1Utility input terminal
2AC output terminal
3Terminal covers
4Mounting holes (4 Total)
5Battery negative input terminal
6Battery positive input terminal
7PV input terminal (MC4)
8External cover
9BMS-Link connection port (RJ45, without isolation design) 5VDC/200mA
10RTS interface
11Dry contact interface
12RBVS interface
13Cable hole
14RS485 interface (DB9 female, with isolation design) 5VDC/200mA
15LCD
16Power switch
17Utility overcurrent protector

5. Setup

Safety Precautions

  • Ensure all power sources are disconnected before installation or maintenance.
  • Use appropriate personal protective equipment (PPE).
  • All wiring must comply with local and national electrical codes.
  • Only qualified personnel should perform installation and wiring.

Mounting the Inverter Charger

The inverter charger should be mounted vertically on a sturdy wall or surface, ensuring adequate ventilation around the unit. Use the four mounting holes provided on the back of the unit.

Inverter charger showing mounting holes and rear panel connections
Rear view of the inverter charger indicating mounting holes and connection ports.

Wiring Diagrams

The UPower-Hi series supports both battery and non-battery modes. Refer to the diagrams below for correct wiring configurations.

Battery Mode Wiring
Wiring diagram for inverter charger in battery mode
Detailed wiring diagram for connecting solar panels, utility/generator, battery, and AC loads to the inverter charger in battery mode. Includes DC breakers, SPDs, and DTU connections.
General Connection Diagram (Battery and No-Battery Modes)
General connection diagram for inverter charger showing both battery and no-battery modes
This diagram illustrates the connections for both battery and no-battery modes, showing solar panels, utility, inverter output, and AC loads.
Simplified connection diagram for solar, battery, loads, and utility/generator
A simplified overview of the system connections, including solar panels, battery, loads, and an optional utility or generator input.

6. Operating Modes

The UPower-Hi series offers flexible operating modes to optimize energy usage and ensure continuous power supply.

Output Models

  • Utility Output: Power is supplied directly from the utility grid.
  • Battery Output: Power is supplied from the battery bank via the inverter.

Charging Modes

The inverter charger supports four distinct charging modes, allowing you to prioritize energy sources based on availability and cost.

Diagram illustrating four charging modes
Visual representation of the four charging modes: Solar Charging, Electricity Utility Priority, Solar Priority, and Hybrid Charging.
  1. Solar Charging: The system primarily charges the battery using solar power.
  2. Electricity Utility Priority: The utility grid is the primary source for charging the battery and supplying loads. Solar power acts as a supplement.
  3. Solar Priority: Solar power is the primary source for charging the battery and supplying loads. The utility grid acts as a supplement when solar power is insufficient.
  4. Hybrid Charging: A combination of solar and utility power is used for charging and supplying loads, optimizing energy flow.

7. Specifications

UP5000-HM8042 Specifications

ItemUP5000-HM8042
Battery Parameters
Rated battery voltage48VDC
Battery input voltage43.2~64VDC
Max. battery charging current80A
Inverter Output
Continuous output power5000W
Max. surge power (3S)8000W
Output voltage range220VAC(-6%~+3%), 230VAC(-10%~+3%)
Output frequency50/60±0.2%
Output WavePure Sine Wave
Load power factor0.2-1 (Load power≤Continuous output power)
Distortion THDTHD≤3% (Resistive load)
80% rated output efficiency92%
Max. Rated output efficiency91%
Max. output efficiency93%
Switch time10ms (Utility to Inverter); 15ms (Inverter to Utility)
Utility Charging
Utility input voltage176VAC~264VAC (Default), 90VAC~280VAC (Programmable)
Utility input frequency40~65Hz
Max. utility charge current60A (30A if Utility input voltage is 90VAC~180VAC)
Solar Charging
Max. PV open circuit voltage500V, 440V
MPPT voltage range120~400V
Max. PV input power4000W
Max. PV charging power4000W
Max. PV charging current80A
Equalize charging voltage58.4V (AGM default)
Boost charging voltage57.6V (AGM default)
Float charging voltage55.2V (AGM default)
Low voltage disconnect voltage43.2V (AGM default)
Tracking efficiency≥99.5%
Temp. compensate coefficient-3mV/℃/2V (Default)
General
Surge current95A
Zero load consumption<1.2A (No PV and utility, AC out is on, fan stops@48V input)
Standby current<0.7A (No PV and utility, AC out is off, fan stops@48V input)
Mechanical Parameters
Dimension (H*W*D)642.5*381.6*149mm
Mounting size620*300mm
Mounting hole sizeφ10mm
Net weight19kg
Environment Parameters
EnclosureIP30
Relative humidity<95% (N.C.)
Environment temperature-20℃~50℃
Storage temperature-25℃~60℃
Altitude<5000m (If altitude exceeds 1000m, actual output power is reduced per IEC62040.)

UP3000-HM10022 Specifications

ItemUP3000-HM10022
Battery Parameters
Rated battery voltage24VDC
Battery input voltage21.6~32VDC
Max. battery charging current100A
Inverter Output
Continuous output power3000W
Max. surge power (3S)6000W
Output voltage range220VAC(-6%~+3%), 230VAC(-10%~+3%)
Output frequency50/60±0.2%
Output WavePure Sine Wave
Load power factor0.2-1 (Load power≤Continuous output power)
Distortion THDTHD≤3% (Resistive load)
80% rated output efficiency92%
Max. Rated output efficiency91%
Max. output efficiency93%
Switch time10ms (Utility to Inverter); 15ms (Inverter to Utility)
Utility Charging
Utility input voltage176VAC~264VAC (Default), 90VAC~280VAC (Programmable)
Utility input frequency40~65Hz
Max. utility charge current80A (40A if Utility input voltage is 90VAC~180VAC)
Solar Charging
Max. PV open circuit voltage450V, 395V
MPPT voltage range80~350V
Max. PV input power4000W
Max. PV charging power2875W
Max. PV charging current100A
Equalize charging voltage29.2V (AGM default)
Boost charging voltage28.8V (AGM default)
Float charging voltage27.6V (AGM default)
Low voltage disconnect voltage21.6V (AGM default)
Tracking efficiency≥99.5%
Temp. compensate coefficient-3mV/℃/2V (Default)
General
Surge current60A
Zero load consumption<1.8A (No PV and utility, AC out is on, fan stops@24V input)
Standby current<1.2A (No PV and utility, AC out is off, fan stops@24V input)
Mechanical Parameters
Dimension (H*W*D)642.5*381.6*149mm
Mounting size620*300mm
Mounting hole sizeφ10mm
Net weight19kg
Environment Parameters
EnclosureIP30
Relative humidity<95% (N.C.)
Environment temperature-20℃~50℃
Storage temperature-25℃~60℃
Altitude<5000m (If altitude exceeds 1000m, actual output power is reduced per IEC62040.)

8. Maintenance

Regular maintenance ensures the longevity and optimal performance of your inverter charger.

  • Visual Inspection: Periodically check for any visible damage, loose connections, or corrosion on terminals and cables.
  • Cleaning: Keep the inverter charger clean and free from dust and debris. Ensure ventilation openings are not blocked. Use a dry cloth for cleaning; do not use liquids.
  • Firmware Updates: Check the manufacturer's website for any available firmware updates to ensure your device has the latest features and bug fixes.
  • Battery Health: If using batteries, regularly monitor their health, voltage, and connections. Ensure they are within the recommended operating parameters.
  • Environmental Conditions: Ensure the operating environment remains within the specified temperature and humidity ranges.

9. Troubleshooting

This section provides general guidance for common issues. For complex problems, contact EPEVER technical support.

  • No Power Output:
    • Check if the power switch (16) is ON.
    • Verify all input (PV, Utility, Battery) and output (AC Loads) connections are secure.
    • Check for any tripped circuit breakers or blown fuses in the system.
    • Examine the LCD (15) for error codes or warning messages.
  • Battery Not Charging:
    • Ensure solar panels are receiving adequate sunlight and are correctly connected to the PV input terminal (7).
    • Verify utility input terminal (1) is connected and receiving power if using utility charging.
    • Check battery connections (5, 6) and ensure battery voltage is within the acceptable range.
    • Confirm charging mode settings on the LCD.
  • Inverter Overload:
    • Reduce the total load connected to the AC output terminal (2).
    • Check the continuous and surge power ratings in the specifications.
  • System Shutdowns:
    • Could be due to over-temperature, over-voltage, or under-voltage. Check environmental temperature and battery voltage.
    • Refer to the LCD for specific shutdown reasons.

10. User Tips

  • Optimal Panel Placement: Ensure solar panels are positioned for maximum sun exposure throughout the day to maximize charging efficiency.
  • Battery Compatibility: Always use batteries compatible with the inverter's voltage and charging parameters. Lithium batteries are often preferred for their performance and longevity, especially with the inverter's built-in protections.
  • Monitor LCD: Regularly check the 4.2-inch LCD display for system status, charging modes, and any alerts to ensure smooth operation.
  • Remote Monitoring: Consider utilizing the optional WiFi or GPRS modules for remote monitoring and control, which can provide convenience and early detection of issues.
  • Ventilation: Maintain clear airflow around the inverter to prevent overheating, especially in high-power applications.

11. Warranty and Support

EPEVER products are designed for reliability and performance. For detailed warranty information, including terms, conditions, and registration, please refer to the official EPEVER website or the warranty card included with your product.

For technical support, troubleshooting assistance, or service inquiries, please contact EPEVER customer service through their official channels. Ensure you have your product model and serial number ready when seeking support.

© 2024 EPEVER. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.