HobbyEagle A3 Pro / A3 Pro V2

Contents

HobbyEagle A3 Pro / A3 Pro V2 Aeroplane RC Flight Controller Stabilizer System Instruction Manual

Model: A3 Pro / A3 Pro V2

1. Product Overview

The HobbyEagle A3 Pro and A3 Pro V2 are high-performance and functional 6-axis gyro and stabilizer systems designed for R/C airplanes. These gyros can be used with nearly any size and type of R/C airplanes, making flying easier and more stable. With the advantage of multi-protocol serial receiver support, they simplify receiver connections.

HobbyEagle A3 Pro V2 Flight Controller

Figure 1: HobbyEagle A3 Pro V2 Flight Controller Unit

HobbyEagle A3 Pro Flight Controller

Figure 2: HobbyEagle A3 Pro Flight Controller Unit

HobbyEagle A3 Pro with included accessories

Figure 3: HobbyEagle A3 Pro Flight Controller with included accessories (cables, double-sided tape)

1.1 Key Features

  • 32-bit MCU and high-precision 6-axis MEMS sensor for reliable performance.
  • Supports 6 flight modes: GYRO OFF, NORMAL, LOCK, ANGLE, LEVEL, and HOVER.
  • Compatible with 3 wing types: standard fixed-wing, delta-wing (flying-wing), and V-tail.
  • Supports most standard PWM receivers, PPM single-line receivers, and multi-protocol digital serial receivers.
  • Separated basic gain adjustment for Aileron, Elevator, and Rudder.
  • Remote master gain adjustment supported.
  • Sub Trim and Travel Limit settings supported.
  • Firmware upgradable (optional data cable required).

2. Setup and Installation

2.1 Port Description

Refer to the table below for a description of the input and output channels.

Table 1: Port Description for A3 Pro

Table 1: Port Description for A3 Pro

2.2 Standard PWM Receiver Connection

Connect the flight controller to your standard PWM receiver and servos as shown in the diagram below. Ensure correct polarity for all connections.

Standard PWM Receiver Connection Diagram for A3 Pro

Figure 4: Standard PWM Receiver Connection Diagram

2.3 Serial Receiver Connection

The A3 Pro / A3 Pro V2 supports various serial receiver protocols. Connect your serial receiver to the 'Serial RX/G' port on the flight controller. When operating in PPM or serial receiver mode, the 'THR Out/AIL' channel functions as the throttle output for the ESC or throttle servo.

Serial Receiver Connection Diagram for A3 Pro V2

Figure 5: Serial Receiver Connection Diagram

Supported Serial Receiver Protocols:

  • PPM Receiver
  • Futaba S.Bus (compatible with FrSky SBUS, RadioLink SBUS, WFLY WBUS)
  • Spektrum DSM/DSMX 1024 Satellite Receiver
  • Spektrum DSM/DSMX 2048 Satellite Receiver
  • Spektrum SRXL
  • Multiplex SRXL / JR XBUS Mode B
  • Graupner SUMD
  • FlySky iBus

3. Operating Instructions

3.1 Flight Modes

The flight controller offers 6 distinct flight modes:

  • GYRO OFF Mode: The gyro stabilization is completely disabled.
  • NORMAL Mode: Provides basic stabilization, assisting with minor corrections.
  • LOCK Mode (Atti-Lock): Locks the aircraft's attitude, maintaining its current orientation.
  • ANGLE Mode: Limits the maximum bank angle, preventing extreme maneuvers.
  • LEVEL Mode (Auto-Level): Automatically levels the aircraft when control sticks are centered.
  • HOVER Mode (Auto-Hover): Maintains a stable hover for compatible aircraft.

3.2 Wing Types

The system supports configuration for three primary wing types:

  • Standard Fixed-Wing
  • Delta-Wing (Flying-Wing)
  • V-Tail

3.3 Gain Adjustment

Individual gain adjustments are available for Aileron, Elevator, and Rudder. A remote master gain feature allows for in-flight adjustment of overall stabilization sensitivity.

3.4 Sub Trim and Travel Limit

The system supports Sub Trim and Travel Limit settings to fine-tune control surface movements.

Video 1: Demonstration of stabilization capabilities, comparing unstabilized vs. stabilized footage.

4. Maintenance

To ensure optimal performance and longevity of your HobbyEagle A3 Pro / A3 Pro V2 flight controller, follow these maintenance guidelines:

  • Keep Clean: Regularly inspect the unit for dust, dirt, or debris. Use a soft, dry cloth to gently clean the exterior. Avoid using solvents or harsh chemicals.
  • Avoid Moisture: Protect the unit from water, humidity, and extreme temperatures. Moisture can damage internal electronic components.
  • Check Connections: Periodically verify that all wires and connectors are securely attached and free from damage. Loose connections can lead to intermittent performance or failure.
  • Physical Inspection: Check the casing for any signs of physical damage, cracks, or loose parts.
  • Firmware Updates: If available, consider updating the firmware to benefit from improvements and new features. Refer to the manufacturer's website for the latest firmware and update instructions.

5. Troubleshooting

If you encounter issues with your HobbyEagle A3 Pro / A3 Pro V2, consider the following troubleshooting steps:

  • No Power/Indicator Light Off:
    • Check all power connections to the flight controller and receiver.
    • Ensure the power source (e.g., LiPo battery) is charged and correctly connected.
  • No Control/Erratic Behavior:
    • Verify all servo and receiver connections are correct and secure.
    • Check your transmitter settings and ensure it's properly bound to the receiver.
    • Confirm the correct wing type and flight mode are selected.
    • Recalibrate the flight controller if necessary (refer to detailed calibration instructions, usually found in the full manual or software).
  • Poor Stabilization:
    • Adjust the gain settings. Start with lower gains and gradually increase until desired stability is achieved without oscillation.
    • Ensure the flight controller is mounted securely and free from vibrations.
    • Check the orientation of the flight controller as per installation instructions.
  • Unexpected Flight Mode Changes:
    • Verify the channel assignment for flight mode switching on your transmitter.
    • Ensure the switch positions correspond to the desired flight modes.

For persistent issues, consult the comprehensive user manual (if available as a PDF) or contact customer support.

6. Specifications

AttributeValue
Brand NameHobbyEagle (Mitoot)
Model NumberA3 Pro / A3 Pro V2
For Vehicle TypeAirplanes
MaterialMetal
Recommend Age14+y
Processor32-bit MCU
SensorHigh-precision 6-axis MEMS sensor
Flight ModesGYRO OFF, NORMAL, LOCK, ANGLE, LEVEL, HOVER
Wing TypesStandard Fixed-Wing, Delta-Wing, V-Tail
Receiver CompatibilityStandard PWM, PPM, Futaba S.Bus, Spektrum DSM/DSMX, SRXL, Multiplex SRXL/JR XBUS Mode B, Graupner SUMD, FlySky iBus
Gain AdjustmentSeparated for Aileron, Elevator, Rudder; Remote Master Gain
Additional FeaturesSub Trim, Travel Limit, Firmware Upgradable

7. User Tips

  • Initial Setup: Always double-check all wiring connections and ensure the flight controller is securely mounted to minimize vibrations.
  • Calibration: Perform a thorough calibration of the flight controller and your radio system before the first flight and after any significant changes to the setup.
  • Gain Tuning: Start with conservative gain settings and gradually increase them during test flights until you achieve optimal stability without any noticeable oscillations or twitching.
  • Flight Mode Practice: Familiarize yourself with each flight mode in a safe, open area before attempting complex maneuvers.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.