1. Introduction
The EPEVER Tracer-AN series MPPT solar charge controller is an advanced device designed to efficiently manage power flow from your solar panels to your battery system. It features high tracking and conversion efficiencies, automatic voltage detection, and comprehensive protection mechanisms, making it suitable for various solar applications.

2. Product Features
- MPPT tracking efficiency above 99.5%
- Maximum charge conversion efficiency as high as 98%
- Support for lead-acid and lithium-ion batteries
- Multiple load work modes
- Charging power and current limitation function
- High-temperature charging power derating function
- Standard Modbus communication protocol with RS485 interface
- Real-time energy statistics function
3. Setup and Installation
This section provides general guidelines for setting up your EPEVER Tracer-AN series solar charge controller. For detailed wiring diagrams and specific installation instructions, please refer to the diagrams provided.
3.1 System Overview
The solar charge controller integrates into a solar power system to manage the energy flow from solar panels to batteries and connected loads. A typical setup includes solar panels, the charge controller, a battery system, and an inverter to power AC loads.

3.2 Battery Compatibility
The controller is compatible with various battery types and automatically identifies 12V/24V battery voltages. Supported battery types include:
- Lithium (LI)
- Sealed (SLD)
- Flooded (FLD)
- Gel (GEL)
- AGM (AGM)

3.3 Application Scenarios
The Tracer-AN series controllers are versatile and can be applied in a wide range of situations, including:
- Solar Cars
- Solar Homes
- Solar Boats
- Solar Street Lights
- Solar Power Generators
- Solar Backpacks

4. Operating Instructions
4.1 Basic Operation
The controller features an LCD screen for displaying system status and basic diagnostic information. Use the "SELECT" and "ENTER" buttons to navigate menus and confirm selections.

4.2 Monitoring and Control
The system can be monitored and controlled in real-time using a mobile phone (via BLE or WIFI modules) or an MT50 remote meter. These accessories are sold separately.
- Mobile App Monitoring: Connect via BLE or WIFI modules (purchased separately) to monitor the system from your smartphone.
- MT50 Remote Meter: Use the MT50 remote meter for direct monitoring and configuration.
- PC Communication: The controller supports standard Modbus communication protocol with an RS485 interface for PC connectivity.

5. Maintenance
To ensure optimal performance and longevity of your EPEVER Tracer-AN series solar charge controller, regular maintenance is recommended:
- Cleanliness: Keep the controller clean and free from dust and debris. Ensure ventilation openings are not obstructed.
- Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
- Environment: Ensure the operating environment temperature remains within the specified range (-25℃ to +45℃).
- Firmware: Check for any available firmware updates from the manufacturer to ensure the controller operates with the latest features and bug fixes.
6. Troubleshooting and Protection Features
The EPEVER Tracer-AN series controller is equipped with 13 intelligent protection features to safeguard your solar power system. The LCD screen provides basic fault diagnostics. If an issue arises, check the display for error codes or indicators.
6.1 Intelligent Protection Features
The controller includes the following built-in protections:
- Over-charging Protection
- Load Short Circuit Protection
- Temperature Compensation
- Overheating Protection (Device and Battery)
- TVS High Voltage Transients Protection
- Overload Protection
- Over Current Protection (PV and Load)
- Short-circuit Protection (PV and Load)
- PV Reverse Polarity Protection
- Battery Reverse Polarity Protection
- Battery Over Voltage Protection
- Battery Over-discharging Protection
- Lithium Battery Low Temperature Protection
- Night Reverse Charging Protection

6.2 Common Issues
If the controller is not functioning as expected, verify the following:
- All connections are secure and correctly wired.
- Battery voltage is within the acceptable range (8-32V).
- PV input voltage does not exceed the maximum open circuit voltage (60V or 100V depending on model).
- No short circuits or overloads on the load terminals.
- The ambient temperature is within the operating range.
7. Specifications
Below are the detailed technical specifications for the EPEVER Tracer-AN series MPPT solar charge controllers.

| Item | Tracer1206AN / Tracer1210AN | Tracer2206AN / Tracer2210AN | Tracer3210AN | Tracer4210AN |
|---|---|---|---|---|
| System nominal voltage | 12/24VDC Auto | |||
| Rated charge current | 10A | 20A | 30A | 40A |
| Rated discharge current | 10A | 20A | 30A | 40A |
| Battery voltage range | 8~32V | |||
| Max. PV open circuit voltage | 60V (at min operating temp) / 46V (at 25℃) | 100V (at min operating temp) / 92V (at 25℃) | ||
| MPP voltage range | (Battery voltage +2V)~36V | (Battery voltage +2V)~72V | ||
| Max. PV input power | 130W/12V, 260W/24V | 260W/12V, 520W/24V | 390W/12V, 780W/24V | 520W/12V, 1040W/24V |
| Self-consumption | ≤12mA | |||
| Discharge circuit voltage drop | ≤0.23V | |||
| Temperature compensation efficient | -3mV/℃/2V (Default) | |||
| Grounding | Common negative | |||
| RS485 interface | 5VDC/200mA | |||
| Working environment temperature | -25℃~+45℃ (100% input and output) | |||
| Storage temperature range | -20℃~+70℃ | |||
| Relative humidity | ≤95%, N.C. | |||
| Enclosure | IP30 | |||
| Dimension (LxWxH) | 172x139x 44mm | 220x154x 52mm | 228x164x55mm | 252x180x63mm |
| Weight | 0.57kg | 0.94kg | 1.26kg | 1.65kg |
Note: ①When a lithium battery is used, the system voltage cannot be identified automatically. ②At minimum operating environment temperature. ③At 25℃ environment temperature.
8. User Tips
No specific user tips were available from reviews or Q&A for this product at this time. Always refer to the detailed instructions for your specific model and setup.
9. Warranty and Support
For warranty information, technical support, or service inquiries regarding your EPEVER Tracer-AN series MPPT solar charge controller, please contact EPEVER customer service or refer to the official EPEVER website.
The product is designed with reliability in mind, and the seller may offer additional service commitments such as free returns within 15 days and guarantees for fast delivery, including compensation for delays and refunds for lost or damaged packages. Specific terms and conditions for these services apply and are managed by the seller and platform.