Hobbyeagle A3 EVO

Contents

Hobbyeagle A3 EVO 6-axis Gyro & Stabilization Balancer Flight Controller User Manual

Model: A3 EVO

1. Introduction

The Hobbyeagle A3 EVO is a 6-axis gyro system designed for fixed-wing aircraft, including 3D F3A planes and F3P models. It provides flight stabilization and balancing, enhancing control and performance. Developed on an AVR platform, it features a high-efficiency algorithm and supports various receiver types.

Hobbyeagle A3 EVO 6-axis Gyro Flight Controller module
Figure 1: Hobbyeagle A3 EVO 6-axis Gyro Flight Controller module.
Hobbyeagle A3 EVO Flight Controller and included accessories: connection cables, capacitor, and mounting pads.
Figure 2: A3 EVO Flight Controller and included accessories.

2. Features

  • 4 Flight Modes: GYRO OFF Mode, NORMAL Mode, LEVEL Mode, and HOVER Mode.
  • 3 Wing Types: Standard, Delta-wing, and V-Tail.
  • Supports Standard PWM receivers, PPM and Futaba S.Bus receivers.
  • Throttle output channel available when using PPM or S.Bus mode.
  • Separate basic gain adjustment for Aileron, Elevator, and Rudder.
  • Remote master gain supported.

3. Specifications

ParameterValue
Main ControllerAVR MCU
SensorMEMS 3-axis sensor
Gyro Scale Range±2000 dps
Accelerometer Scale Range±4g
PWM Output Limit970μS to 2070μS
PWM Output Neutral1520μS
Input Voltage4.8V to 8.4V (H.V. 2S Lithium Battery Supported)
Operating Temperature-10℃ to 50℃
Size43×27×14mm
Weight10g (excluding wires)
MaterialMetal
Recommended Age14+ years

4. Setup

4.1. Wiring Diagram

Proper connection of the A3 EVO to your receiver, servos, and ESC is crucial for correct operation. Refer to the diagram below for standard wiring. Ensure all connections are secure and correctly oriented.

Wiring diagram for Hobbyeagle A3 EVO Flight Controller connected to a receiver (Futaba FASSTest R7008SB), servos (rudder, elevator, aileron), and ESC. Shows connections for OUT1-3, SBUS/PPM/G, MODE, RUD, ELE, THR Out/AIL, AIL, ELE, RUD, and power.
Figure 3: A3 EVO Wiring Diagram.

Key Connections:

  • OUT1, OUT2, OUT3: Connect to respective servos or other output devices.
  • SBUS/PPM/G: Connect to your receiver's SBUS or PPM output. This port also serves as a general input.
  • MODE: Connect to a switch channel on your receiver for flight mode selection.
  • RUD, ELE, AIL (Input): Connect to the Rudder, Elevator, and Aileron channels from your receiver.
  • THR Out/AIL: Throttle output or Aileron input, depending on configuration.
  • SET: Button for configuration.
  • LED: Status indicator.
  • Power (+/-): Connect to your power source, typically from the ESC or a separate BEC.

4.2. Initial Configuration

After wiring, perform the initial setup as per the detailed instructions in the official user manual. This typically involves:

  1. Mounting the A3 EVO securely in your aircraft.
  2. Calibrating the gyro and accelerometer.
  3. Setting up the wing type (Standard, Delta-wing, V-Tail).
  4. Configuring the flight modes on your transmitter.
  5. Adjusting basic gain settings for Aileron, Elevator, and Rudder.

5. Operating Instructions

5.1. Flight Modes

The A3 EVO offers four distinct flight modes, switchable via a 3-position switch on your transmitter. The LED on the unit indicates the current mode:

LED indicator states for A3 EVO flight modes: Solid Blue (NORMAL), Solid Red (LEVEL), Solid Blue & Red (HOVER), LED Off (GYRO OFF).
Figure 4: LED Indicator for Flight Modes.
  • NORMAL Mode (Solid Blue LED): Standard gyro stabilization.
  • LEVEL Mode (Solid Red LED): Auto-leveling function, helps return the aircraft to a level flight attitude.
  • HOVER Mode (Solid Blue & Red LED): Designed for 3D flight, assists in maintaining a hover.
  • GYRO OFF Mode (LED Off): Gyro stabilization is disabled.

You can configure different mode allocations for your 3-position switch. The default setting is MODE 1: NORMAL - LEVEL - HOVER.

Table showing 4 mode allocations for A3 EVO corresponding to a 3-position switch: NORMAL, LEVEL, HOVER, and GYRO OFF combinations.
Figure 5: Flight Mode Allocation Table.

5.2. Gain Adjustment

Separate basic gain adjustments are available for Aileron, Elevator, and Rudder. Remote master gain can also be used for in-flight adjustments. Refer to the full manual for detailed instructions on adjusting these settings to suit your aircraft and flying style.

6. Maintenance

The A3 EVO is a robust electronic device. To ensure its longevity and optimal performance:

  • Keep the unit clean and free from dust and debris.
  • Avoid exposing the unit to extreme temperatures or moisture.
  • Ensure all connections are secure before each flight.
  • Regularly check for any signs of physical damage to the unit or its wiring.
  • Store in a dry, cool place when not in use.

7. Troubleshooting

If you encounter issues with your A3 EVO, consider the following:

  • No LED indication: Check power connections and input voltage (4.8V to 8.4V).
  • Incorrect flight mode: Verify your transmitter's 3-position switch settings and the wiring to the MODE port.
  • Unstable flight:
    • Check gain settings; they might be too high or too low.
    • Ensure the unit is securely mounted and free from vibrations.
    • Verify correct orientation of the unit as per the full manual.
    • Confirm all servo connections are correct and functioning.
  • No control response: Check receiver connection (PWM, PPM, or S.Bus) and ensure the receiver is bound to your transmitter.

For more detailed troubleshooting, consult the official user manual.

8. User Tips

  • Engine Compatibility: While the A3 EVO is versatile, for aircraft with larger engines (e.g., 55cc), ensure your specific setup's power requirements and vibration levels are compatible with the controller's specifications. Consult the full manual or manufacturer for specific recommendations if unsure.
  • Mounting: Securely mount the gyro to minimize vibrations, which can affect performance. Use the provided mounting pads.
  • First Flight: Always perform initial flights in a safe, open area and start with lower gain settings, gradually increasing them as you become comfortable with the aircraft's response.

9. Support and Further Information

For comprehensive instructions, advanced settings, and detailed diagrams, please refer to the official Hobbyeagle A3 EVO User Manual V1.0, available at: https://manuals.plus/m/3f22a1b6e1be52374bd4aaa9b912bfff68ff61e5e9bfaca80f814ddea9883277

This manual provides essential information for setup and operation. For any issues not covered here, please consult the full PDF manual or contact Hobbyeagle support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.