1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your DUALTRON LED Controller Wires Hub. This device is designed to manage the LED lighting system when integrated with an EY4 display on MINIMOTORS DUALTRON VICTOR LUXURY Plus electric scooters. Please read this manual thoroughly before installation and use.
2. Safety Information
- Always disconnect the scooter's power source before attempting any installation or maintenance.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Do not expose the controller to water or extreme temperatures.
- If you are unsure about any step, consult a qualified technician.
3. Package Contents
Verify that all items are present and undamaged:
- DUALTRON LED Controller Wires Hub
- Instruction Manual (this document)
4. Product Overview
The DUALTRON LED Controller Wires Hub acts as a central connection point and control unit for the LED lighting system on compatible electric scooters. It facilitates the connection between the scooter's EY4 display and various LED components, allowing for integrated control.
Figure 1: Front view of the LED Controller Wires Hub.
Figure 2: Angled view highlighting the multiple output connectors.
5. Installation and Setup
Follow these steps carefully to install the LED Controller Wires Hub:
- Prepare the Scooter: Ensure the electric scooter is turned off and the battery is disconnected to prevent accidental power surges or short circuits during installation.
- Locate Mounting Area: Identify a suitable, dry, and secure location on your scooter to mount the LED Controller Wires Hub. This area should be protected from direct water exposure and excessive vibration.
- Connect to EY4 Display: Identify the designated wiring harness from your EY4 display for LED control. Connect the corresponding input wires from the LED Controller Wires Hub to this harness. Ensure the connectors are firmly seated.
- Connect LED Components: Connect your scooter's LED lights (e.g., deck lights, stem lights) to the output connectors on the LED Controller Wires Hub. Pay attention to color coding and connector types to ensure correct polarity and function. The hub features multiple output ports for various LED accessories.
- Secure Wiring: Use cable ties or appropriate fasteners to neatly secure all wires, preventing them from snagging or interfering with moving parts.
- Reconnect Power: Once all connections are secure and verified, reconnect the scooter's battery and turn on the power.
Figure 3: Close-up of various connectors on the hub.
Figure 4: Detailed view of color-coded wiring connections.
6. Operating Instructions
The DUALTRON LED Controller Wires Hub operates in conjunction with your scooter's EY4 display. Refer to your scooter's main user manual for specific instructions on how to access and control LED functions via the EY4 display.
- Power On/Off: The LED lights connected through the hub will typically power on and off with the scooter's main power.
- Mode Selection: Use the controls on your EY4 display to cycle through different LED lighting modes, colors, or patterns, if supported by your scooter's system.
- Brightness Adjustment: Adjust LED brightness via the EY4 display settings, if available.
7. Maintenance
To ensure the longevity and optimal performance of your LED Controller Wires Hub:
- Regular Inspection: Periodically check all wiring connections for looseness, corrosion, or damage.
- Keep Dry: Ensure the controller remains dry and protected from moisture.
- Cleanliness: Gently clean the exterior of the controller with a dry, soft cloth if necessary. Avoid using harsh chemicals or abrasive materials.
- Environmental Protection: Avoid exposing the unit to extreme heat or prolonged direct sunlight.
8. Troubleshooting
If you encounter issues with your LED Controller Wires Hub, refer to the following table:
| Problem | Possible Cause | Solution |
|---|---|---|
| LEDs not turning on | No power to controller Loose connection Faulty LED strip/component | Check scooter's main power and battery connection. Verify all connections to the controller and LEDs are secure. Test LED components directly if possible. |
| LEDs not responding to display controls | Incorrect wiring to EY4 display EY4 display settings incorrect | Review wiring between controller and EY4 display. Consult scooter's manual for EY4 display LED control settings. |
| Some LEDs not working | Faulty individual LED component Loose connection to specific LED | Inspect wiring to the non-functional LED. Replace faulty LED component if necessary. |
9. Specifications
| Feature | Detail |
|---|---|
| Brand Name | DUALTRON |
| Origin | Mainland China |
| High-concerned chemical | None |
| Package Dimensions (L x W x H) | 15 cm x 9 cm x 11 cm |
| Package Weight | 0.2 kg |
Figure 5: Top view of the controller unit.
10. User Tips
- Secure Mounting: Ensure the controller is mounted in a location that minimizes exposure to road debris and impacts.
- Cable Management: Proper cable routing and management not only looks cleaner but also prevents wires from being pinched or damaged during scooter operation.
- Compatibility Check: Always double-check that this specific wires hub is compatible with your exact scooter model (MINIMOTORS DUALTRON VICTOR LUXURY Plus) and display type (EY4) before installation.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the DUALTRON Official Store or your authorized dealer. Keep your purchase receipt as proof of purchase.
