1. Introduction
This instruction manual provides essential information regarding the original spare parts for your Roborock Q Revo S and Q Revo Pro robot vacuum cleaners. Regular replacement and proper maintenance of these accessories are crucial for maintaining the cleaning efficiency and extending the lifespan of your device. This guide will cover product identification, compatibility, installation, maintenance, and specifications for each component.
2. Product Overview & Compatibility
These spare parts are designed specifically for the Roborock Q Revo S and Roborock Q Revo Pro robot vacuum cleaner models. Please ensure your robot vacuum model matches the compatible models listed below before installation.
2.1. Compatible Models
- Roborock Q Revo S
- Roborock Q Revo Pro
2.2. Incompatible Models
These parts are NOT suitable for:
- Roborock Q Revo
- Roborock Q Revo MaxV
- Roborock Q Revo Crve
- Roborock Q Revo Master
2.3. Available Spare Parts
The following original spare parts are available:
Overview of Roborock Q Revo S/Pro spare parts kit.
3. Setup and Installation
Always power off your robot vacuum cleaner and disconnect it from the charging dock before attempting to replace any parts.
3.1. Main Brush Installation
- Turn the robot vacuum over.
- Locate the main brush cover and unlatch it.
- Remove the old main brush.
- Insert the new main brush, ensuring the ends align with the slots. The main brush assembly includes a rubber brush, brush cap, and brush bearing.
- Close the main brush cover until it latches securely.
Real picture of the main brush.
Exploded view of the main brush assembly.
3.2. Side Brush Installation
- Turn the robot vacuum over.
- Locate the side brush and unscrew it (if applicable).
- Remove the old side brush.
- Align the new side brush with the post and press it down until it clicks into place, or screw it in if required.
Close-up of a side brush.
Real picture of a side brush.
3.3. Filter Installation
- Open the robot vacuum's dustbin compartment.
- Remove the dustbin.
- Take out the old filter from the dustbin.
- Insert the new filter into the designated slot in the dustbin.
- Reinstall the dustbin into the robot vacuum.
Washable filter design.
3.4. Mop Cloth Installation
- Remove the mop module from the robot vacuum.
- Detach the used mop cloth from the module.
- Attach the new mop cloth securely to the mop module.
- Reinstall the mop module onto the robot vacuum.
Mop cloth features: efficient water locking and strong cleaning.
Mop pads attached to the robot vacuum.
3.5. Dust Bag Installation
- Open the auto-empty station's dust bag compartment.
- Carefully remove the full dust bag.
- Insert a new dust bag into the compartment, ensuring it is properly seated.
- Close the compartment lid.
Dust bag capacity (2.7L) and auto-empty station integration.
4. Maintenance
Regular maintenance and timely replacement of spare parts are essential for optimal cleaning performance and to prolong the life of your robot vacuum.
- Main Brush: Inspect weekly, clean hair and debris. Replace every 6-12 months depending on usage.
- Side Brush: Inspect weekly, clean hair and debris. Replace every 3-6 months depending on usage.
- Filter: Clean weekly by tapping out dust or rinsing with water (if washable). Ensure it is completely dry before reinstallation. Replace every 3-6 months.
- Mop Cloth: Wash after each use. Replace every 1-3 months depending on usage and wear.
- Dust Bag: Replace when full. The large capacity dust bag allows for up to 7 weeks of use without emptying, depending on usage habits and environmental factors.
5. Troubleshooting
This section addresses common issues related to spare parts. For comprehensive robot vacuum troubleshooting, please refer to your main robot vacuum manual.
- Reduced Cleaning Performance: Check if brushes are tangled with hair or debris. Ensure filters are clean and not clogged. Replace worn-out parts.
- Unusual Noises: Inspect main brush and side brushes for foreign objects or damage. Ensure all parts are correctly installed.
- Dustbin Not Filling / Suction Issues: Check if the dust bag is correctly installed and not full. Ensure the filter is clean and not blocked.
6. Specifications
| Attribute | Detail |
|---|---|
| Brand Name | roborock |
| Model Number | Roborock Q Revo S / Q Revo Pro |
| Type | Vacuum Cleaner Parts |
| Material | Non-woven Fabric, Silicone, Metal, Plastic |
| High-concerned chemical | None |
| Origin | Mainland China |
| Package Weight | 0.75 kg |
| Package Dimensions | 35cm (Length) x 25cm (Width) x 15cm (Height) |
7. User Tips
- Always use original, high-quality spare parts to ensure compatibility and optimal performance of your robot vacuum.
- Establish a regular replacement schedule for all accessories based on your usage frequency and environment to maintain peak cleaning efficiency.
- For washable filters, ensure they are completely air-dried before reinstallation to prevent mold growth and maintain filtration effectiveness.
- Periodically check brushes for tangled hair or debris, especially if you have pets, to prevent damage and maintain effective cleaning.
8. Warranty and Support
For any warranty claims or technical support regarding your Roborock Q Revo S or Q Revo Pro robot vacuum cleaner and its original spare parts, please contact Roborock customer service or refer to the official Roborock website for detailed warranty information and support options.
