MN MODEL MJX Hyper Go 20208

Contents

MJX Hyper Go 20208 Remote Control Car User Manual

1/20 Scale Brushless 4WD High-Speed Off-Road Truck

1. Safety Precautions

  • Age Recommendation: This product is not suitable for children under 36 months. Recommended age for use is 14 years and older.
  • Always operate the RC car in open areas, away from people, pets, and obstacles.
  • Do not operate the RC car near water or in wet conditions to prevent damage to electronic components.
  • Ensure all connections are secure before operation.
  • Use only the designated charging device for the Li-Po battery.
  • Do not crush or heat the battery. Do not dispose of batteries in fire.

2. Package Contents

The MJX Hyper Go 20208 package includes the following items:

  • MJX Hyper Go 20208 RC Car (with body battery installed)
  • 2.4G Remote Control
  • USB Charging Cable
  • Screwdriver
  • Instruction Manual
Exploded view of the RC car components including body, chassis, remote, and battery.
Figure 2.1: Exploded view of the MJX Hyper Go 20208 RC Car and its accessories.
Video 2.1: Unboxing and initial overview of the MJX Hyper Go 20208 RC car and remote control.

3. Setup

3.1 Remote Control Battery Installation

  1. Open the battery compartment cover on the back of the remote control.
  2. Insert two (2) AA batteries (not included), ensuring correct polarity.
  3. Close the battery compartment cover securely.
Remote control with battery compartment visible.
Figure 3.1: Remote control and car components, showing the remote's battery area.

3.2 Vehicle Battery Installation and Charging

  1. The vehicle comes with a SF 7.4V 850mAh 25C Li-Po battery. Ensure it is fully charged before first use.
  2. To charge, connect the Li-Po battery to the provided USB charging cable. Connect the USB cable to a suitable USB power source (e.g., computer USB port, USB wall adapter).
  3. The charging indicator will show the charging status (refer to the USB charging cable's specific instructions for light indications).
  4. Once charged, connect the battery to the vehicle's power connector. The battery is modular and enclosed within the chassis.
RC car in action, highlighting the Li-Po 7.4V-850mAh battery.
Figure 3.2: The Li-Po 7.4V-850mAh battery for the RC car.

3.3 Pairing the Remote Control and Vehicle

  1. Turn on the remote control first using the power switch. The indicator light on the remote will blink.
  2. Turn on the RC car. The indicator light on the car will blink.
  3. Wait a few seconds for the remote control and car to automatically pair. Once paired, the indicator lights on both the remote and the car will become solid.
  4. If pairing fails, turn off both devices and repeat the steps.

4. Operating Instructions

4.1 Remote Control Functions

Diagram illustrating the remote control functions.
Figure 4.1: Remote Control Function Analysis.
  • Power Switch: Turns the remote control ON/OFF.
  • CH1: ST (Steering): Controls the left and right steering of the vehicle.
  • CH2: TH (Throttle): Controls the forward and backward movement, and speed of the vehicle.
  • CH3: Light Switch Control: Toggles the vehicle's LED lights ON/OFF.
  • ST.TRIM (Steering Gear Trim): Adjusts the neutral position of the steering. If the car pulls to one side when the steering wheel is centered, use this trim to correct it.
  • ST.D/R (Steering Trim): Adjusts the maximum steering angle.
  • TH.TRIM (Throttle Trim): Adjusts the neutral position of the throttle. If the car moves slightly forward or backward when the throttle trigger is centered, use this trim to correct it.
  • TH.D/R (Throttle Trim): Adjusts the maximum throttle output, controlling the top speed.

4.2 Driving the Vehicle

  1. After successful pairing, gently pull the throttle trigger (CH2) to move the car forward. Push it forward to reverse.
  2. Turn the steering wheel (CH1) left or right to steer the vehicle.
  3. Adjust the trim settings (ST.TRIM, TH.TRIM) as needed for optimal control.
  4. The remote control has a range of up to 100 meters.

5. Maintenance

5.1 Battery Care and Storage

Warm Tips for battery storage and maintenance.
Figure 5.1: Battery storage and maintenance tips.
  • Store the Li-Po battery at approximately half charge (storage voltage) in a cool, dry place.
  • If not used for a long time, charge and discharge the battery once every 3 months to maintain its health.
  • Always disconnect the battery from the vehicle when not in use.

5.2 General Cleaning and Inspection

  • The car features a quick-release shell body design, allowing for easy removal for cleaning and inspection of internal components.
  • After each use, especially in dusty or dirty environments, clean the vehicle to remove dirt and debris. Use a soft brush or compressed air.
  • Regularly check for loose screws, damaged parts, or worn tires. Tighten any loose screws and replace damaged components as necessary.
  • Inspect the oil pressure shock absorbers and ensure they are functioning smoothly.
Image demonstrating the quick-release shell body design.
Figure 5.2: Quick release shell body design for easy maintenance.
Image of the RC car chassis with the body shell removed.
Figure 5.3: Chassis view with body removed for access to components.

6. Troubleshooting

  • Car not responding: Ensure both the remote control and car are powered on and successfully paired (solid indicator lights). Check remote control batteries and vehicle battery charge level.
  • Poor control range: Ensure there are no strong interference sources nearby. Check battery levels of both the remote and car.
  • Car pulls to one side: Adjust the ST.TRIM knob on the remote control until the car drives straight.
  • Car moves without throttle input: Adjust the TH.TRIM knob on the remote control until the car remains stationary when the throttle trigger is centered.
  • Reduced speed/power: The vehicle battery may be low. Recharge the Li-Po battery.

7. Specifications

Product Specification table for HYPERGO 20208.
Figure 7.1: HYPERGO Product Specification Overview.
FeatureDetail
Product Model20208
Brand NameMN MODEL
Car Shell ColorRed (as depicted in images)
Scale1:20
Maximum Speed39 KM/H
Remote Control Distance100m
Flight Time (Usage Time)About 10-15 minutes
Charging MethodUSB Charging Cable
Dimensions (L*W*H)220*180*105mm
Wheelbase125mm
Tire Track145mm
Tire Diameter65mm
Vehicle Weight553g
Motor1806 Brushless Motor
ESC35A Integrated Power Modulation (three-in-one circuit board)
Steering Servo9g Digital Steering Gear
Remote Control Frequency2.4G
Remote Control BatteryAA*2 (not included)
Body BatterySF 7.4V850mah 25C Li-Po
MaterialMetal, Plastic, Carbon Fiber
Power TypeBrushless
State of AssemblyReady-to-Go
Control Channels6 channels
Controller ModeMODE1, MODE2
FeaturesRemote Control
DesignDirt Bike
OriginMainland China

8. User Tips

  • The 1/20 scale makes this RC car very compact and portable, ideal for taking on camping trips or to gatherings with friends.
  • The brushless motor and 35A ESC provide strong power, allowing for impressive maneuvers.
  • The nylon body offers good protection for the internal components.
  • All car parts are enclosed, contributing to its durability and value.
  • Remember to fully charge the battery before each use for maximum performance.

9. Warranty and Support

For specific warranty information, please refer to the terms provided by your seller at the time of purchase. Keep your proof of purchase for any warranty claims.

For technical support or inquiries regarding replacement parts, please contact the seller or manufacturer directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.