EPever TracerAN-G3 Series (Tracer1206ANG3, Tracer2206ANG3, Tracer1210ANG3, Tracer2210ANG3, Tracer3210ANG3, Tracer4210ANG3)

Contents

EPEVER TracerAN-G3 Series MPPT Solar Charge Controller User Manual

Models: Tracer1206ANG3, Tracer2206ANG3, Tracer1210ANG3, Tracer2210ANG3, Tracer3210ANG3, Tracer4210ANG3

1. Introduction

The EPEVER TracerAN-G3 series is an advanced Maximum Power Point Tracking (MPPT) solar charge controller designed for off-grid solar systems. It efficiently manages power flow from solar panels to batteries, ensuring optimal charging and extending battery lifespan. This series features high tracking efficiency, compatibility with various battery types, and robust protection mechanisms.

EPEVER Tracer2210ANG3 MPPT Solar Charge Controller front view
Figure 1: EPEVER TracerAN-G3 Series MPPT Solar Charge Controller

Key Features:

  • Innovative MPPT Algorithm for enhanced tracking and response speeds.
  • Reduced power losses and minimized downtime.
  • Improved efficiency across various power segments.
  • Optimized energy extraction in all scenarios.
  • Lithium Battery Compatibility.
  • Advanced Battery Care and Constant Voltage Output.
  • Seamless Operation.
  • RS485 communication for external monitoring.
  • Energy Efficient & Quiet operation.
  • Durability & Protection features.
TracerAN-G3 Series features list
Figure 2: TracerAN-G3 Series Key Features

2. Setup and Installation

2.1 Safety Precautions

  • Ensure all connections are secure and correct before powering on.
  • Avoid short circuits.
  • Install in a well-ventilated area, away from flammable materials.
  • Wear appropriate personal protective equipment (PPE) during installation.
  • Disconnect all power sources (PV and battery) before wiring or maintenance.

2.2 Wiring Diagram

The controller connects to the solar panels (PV), battery, and DC load. Ensure correct polarity for all connections.

Wiring diagram for solar charge controller with PV, battery, inverter, and AC load
Figure 3: Typical System Connection Diagram

Connection Order:

  1. Connect the battery to the controller.
  2. Connect the solar panel to the controller.
  3. Connect the DC load to the controller (if applicable).

Note: The controller can be used without a battery for certain configurations, as indicated by the 'Can be used without battery' feature.

EPEVER Tracer2210ANG3 controller with text 'Can be used without battery'
Figure 4: Controller Usability Without Battery

2.3 Remote Meter (MT52) Connection

The MT52 remote meter can be connected via an RJ45 communication port to monitor and program parameters.

MT52 remote meter connection diagram via RJ45
Figure 5: MT52 Remote Meter Connection

3. Operating Instructions

3.1 Display and Navigation

The controller features an LCD display and navigation buttons (SELECT, ENTER) for monitoring system status and adjusting settings. The MT52 remote meter provides an enhanced interface for these functions.

MT52 remote meter display showing monitoring and setting parameters
Figure 6: MT52 Remote Meter Interface

3.2 Battery Charging Stages

The controller employs an advanced MPPT algorithm to ensure stable and constant charging through various stages:

  • Bulk Charge: Maximum current is delivered to the battery.
  • Boost Charge: Voltage is raised to ensure full charge.
  • Float Charge: Maintains battery at a constant voltage.
  • Equalize Charge: Periodically overcharges to balance cell voltages (for certain battery types).
Battery charging stages diagram: Equalize, Boost, Float, Bulk
Figure 7: Battery Charging Stages

3.3 Battery Type Selection

The controller supports various battery types including Lead-acid, Lithium (Li, LiFePO4), and user-defined settings. Proper battery type selection is crucial for optimal charging and battery health.

Supported battery types: Lead-acid, Li, LiFePO4, User
Figure 8: Supported Battery Types

How to set battery parameters using MT52:

  1. Choose "Control Para".
  2. Press "OK".
  3. Press "OK" again.
  4. Press "▲" or "▼" to navigate, then press "OK" to save.
  5. Continue to the next setting.
  6. Select battery type from options like Sealed (default), User, Li(NiCoMn)O2, LiFePO4, Flooded, Gel.
MT52 screen showing battery type selection menu
Figure 9: MT52 Battery Parameter Setting

4. Maintenance

Regular maintenance ensures the longevity and optimal performance of your solar charge controller.

4.1 General Maintenance

  • Cleanliness: Keep the controller clean and free from dust and debris. Use a dry cloth for cleaning.
  • Connections: Periodically check all wiring connections for tightness and corrosion. Loose connections can cause overheating and power loss.
  • Ventilation: Ensure the installation area remains well-ventilated to prevent overheating.
  • Firmware: Check for any available firmware updates from the manufacturer to ensure optimal performance and access to new features.

4.2 Battery Maintenance

  • Inspection: Regularly inspect batteries for any signs of damage, swelling, or leaks.
  • Terminals: Clean battery terminals to remove any corrosion.
  • Water Levels (Flooded Batteries): For flooded lead-acid batteries, check electrolyte levels and top up with distilled water as needed.

5. Troubleshooting

This section provides common issues and their potential solutions.

5.1 Common Issues and Solutions

  • No Power/Display:
    • Check battery connections and voltage.
    • Ensure the battery is charged above the minimum operating voltage.
    • Verify wiring polarity.
  • No Charging from PV:
    • Check PV panel connections and ensure they are receiving sunlight.
    • Verify PV open-circuit voltage (Voc) and short-circuit current (Isc) are within controller limits.
    • Ensure PV polarity is correct.
  • Battery Not Fully Charged:
    • Confirm correct battery type setting in the controller.
    • Check battery health and capacity.
    • Ensure PV input power is sufficient for the load and battery.
  • Overheating:
    • Ensure adequate ventilation around the controller.
    • Check for loose connections or excessive load.
    • Verify ambient temperature is within operating limits.
  • Communication Errors (MT52/BLE/WiFi):
    • Check RJ45 cable connections for the MT52.
    • Ensure Bluetooth/WiFi modules are properly connected and configured.
    • Refer to the specific module's manual for detailed troubleshooting.

6. Specifications

6.1 Electrical Parameters (TracerAN-G3 Series)

ParameterTracer1206ANG3Tracer2206ANG3Tracer1210ANG3Tracer2210ANG3Tracer3210ANG3Tracer4210ANG3
Battery Rated Voltage12/24VDC Auto-recognition①
Rated Charging Current10A20A10A20A30A40A
Rated Discharge Current10A20A10A20A30A40A
Controller Work Voltage Range8~31V
PV Maximum Open-circuit Voltage60V② / 46V③100V② / 92V③
MPPT Voltage Range(Battery voltage +2V)~36V(Battery voltage +2V)~72V
Rated Charging Power130W/12V, 260W/24V260W/12V, 520W/24V130W/12V, 260W/24V260W/12V, 520W/24V390W/12V, 780W/24V520W/12V, 1040W/24V
Static Losses≤8mA (12V), ≤5mA (24V)
Discharge-circuit Voltage Drop≤0.23V
Temperature Compensation④-3mV/℃/2V (Default)
Grounding TypeCommon negative
RS485 Port5VDC/200mA (RJ45)
LCD Backlight TimeDefault: 60S, Range: 0~999S (0 seconds: backlight is ON all the time)

6.2 Environmental Parameters

ParameterValue
Work Temperature Range⑤-25℃~+45℃ (100% loads working)
Storage Temperature Range-20℃~+70℃
Relative Humidity<95% (N.C.)
EnclosureIP30
Dimension (LxWxH)Tracer1206AN/1210AN: 172x139x44mm
Tracer2206AN/2210AN: 220x154x52mm
Tracer3210AN: 228x164x55mm
Tracer4210AN: 252x180x63mm
Mounting Size (LxW)Tracer1206AN/1210AN: 124x130mm
Tracer2206AN/2210AN: 170x145mm
Tracer3210AN: 170x155mm
Tracer4210AN: 204x171mm
Mounting Hole Sizeφ5mm
TerminalTracer1206AN/1210AN: 12AWG (4mm²)
Tracer2206AN/2210AN/3210AN/4210AN: 6AWG (16mm²)
Recommended Wire SizeTracer1206AN/1210AN: 12AWG (4mm²)
Tracer2206AN/2210AN: 10AWG (6mm²)
Tracer3210AN: 8AWG (10mm²)
Tracer4210AN: 6AWG (16mm²)
Net WeightTracer1206AN/1210AN: 0.57kg
Tracer2206AN/2210AN: 0.94kg
Tracer3210AN: 1.26kg
Tracer4210AN: 1.65kg

① When a lithium battery is used, the system voltage isn't automatically identified.
② At minimum operating environment temperature.
③ At 25℃ environment temperature.
④ When a lithium battery is used, the temperature compensation coefficient will be 0 and can't be changed.
⑤ The controller can full load working in the working environment temperature. When the internal temperature reaches 81℃, the reducing charging power mode is turned on.

6.3 MT52 Remote Meter Specifications

ParameterValue
Electrical Parameter
Self-consumptionBacklight ON <23mA
Backlight OFF <15mA
Mechanical Parameter
Faceplate dimension98mm × 98mm
Frame dimension114mm × 114mm
Communication portRJ45
Communication cable (m)Standard: 2m, Longest: 50m
Net weightSimple package: 0.23 Kg, Standard package: 0.32kg
Environmental Parameter
Environment temperature-20℃~+70℃

7. User Tips

  • Optimal Panel Orientation: Ensure your solar panels are angled correctly towards the sun for maximum energy harvest, especially during peak sunlight hours.
  • Wire Sizing: Always use the recommended wire sizes to minimize voltage drop and ensure efficient power transfer. Undersized wires can lead to significant energy loss and potential safety hazards.
  • Battery Compatibility: Double-check that the selected battery type in the controller settings matches your actual battery chemistry (e.g., Lead-acid, LiFePO4). Incorrect settings can damage your battery.
  • Regular Monitoring: Periodically check the controller's display or remote meter for system status, charging current, and battery voltage to ensure everything is operating as expected.
  • Environmental Considerations: Install the controller in a location that is protected from direct sunlight, rain, and excessive dust to prolong its lifespan.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official EPEVER website or contact your authorized dealer. Keep your purchase receipt as proof of purchase for any warranty claims.

© 2024 EPEVER. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.