QCY T13 Anc2

Contents

QCY T13 ANC2 Wireless Earphones User Manual

Model: T13 ANC2 | Brand: QCY

Introduction

Thank you for choosing the QCY T13 ANC2 Wireless Earphones. These in-ear Bluetooth earphones feature Active Noise Cancellation (ANC) for an immersive audio experience, coupled with a comfortable design and extended battery life. This manual provides detailed instructions to help you set up, operate, and maintain your earphones for optimal performance.

White QCY T13 ANC2 earbuds and charging case
QCY T13 ANC2 Wireless Earphones in white, with charging case.

Setup

1. Unboxing and Initial Inspection

Carefully unpack your QCY T13 ANC2 earphones and ensure all components are present:

  • QCY T13 ANC2 Earbuds (Left and Right)
  • Charging Case
  • USB Charging Cable
  • User Manual (this document)
  • Eartips (various sizes, usually pre-installed or in a separate bag)

2. Charging the Earphones and Case

Before first use, fully charge both the earphones and the charging case.

  1. Place the earbuds into the charging case. Ensure the charging contacts align.
  2. Important: Some new earphones may have a protective film on the charging terminals. Please remove this film before placing the earbuds in the case to ensure proper charging.
  3. Connect the USB charging cable to the charging port on the case and to a power source (e.g., USB wall adapter, computer USB port).
  4. The indicator light on the charging case will show the charging status. Refer to the LED indicator section for details.
  5. A full charge typically takes approximately 2 hours for the case and earbuds.
QCY T13 ANC2 charging case with USB-C cable connected
Connect the charging case to a power source using the provided USB cable.
QCY T13 ANC2 earbuds inside the charging case, showing charging contacts
Ensure earbuds are properly seated in the charging case for contact with charging terminals.

3. Bluetooth Pairing

The QCY T13 ANC2 uses Bluetooth 5.3 for a stable connection.

  1. Open the charging case. The earbuds will automatically enter pairing mode (if not already paired). The indicator light on the earbuds may flash.
  2. On your device (smartphone, tablet), go to Bluetooth settings and turn Bluetooth on.
  3. Search for available devices. You should see "QCY T13 ANC2" in the list.
  4. Select "QCY T13 ANC2" to connect. Once connected, you will hear a confirmation tone, and the earbud indicator lights will turn off or flash slowly.
  5. If pairing fails, place the earbuds back in the case, close the lid, wait a few seconds, then open the lid and try again.

Note on Compatibility: These earphones are designed for optimal compatibility with Android (e.g., Samsung, LG) and iOS (iPhone) operating systems. Compatibility with other devices such as PCs, notebooks, gaming devices, or certain tablets is not guaranteed.

Operating Instructions

The QCY T13 ANC2 earphones feature intuitive touch controls on each earbud.

Diagram of QCY T13 ANC2 earbuds showing touch control functions
Touch control functions for QCY T13 ANC2 earbuds.

Touch Controls

ActionLeft EarbudRight Earbud
Play/Pause Music-Double Tap
Answer/End Call-Double Tap
Reject CallLong Press (1.5s)Long Press (1.5s)
Skip Track BackwardLong Press (1.5s)-
Skip Track Forward-Long Press (1.5s)
Activate Voice AssistantTriple Tap-
ANC On/OffDouble Tap-
Game Mode On/Off-Triple Tap

Active Noise Cancellation (ANC)

The QCY T13 ANC2 features Active Noise Cancellation to reduce ambient noise. Double tap the left earbud to toggle ANC on or off. When ANC is active, you will experience a significant reduction in surrounding sounds, enhancing your listening experience.

Game Mode

For an optimized gaming experience, triple tap the right earbud to activate or deactivate Game Mode. This mode typically reduces audio latency, providing better synchronization between audio and video during gameplay.

Using the QCY App

The earphones support the QCY app, which may offer additional customization options, equalizer settings, and firmware updates. Download the official QCY app from your device's app store for enhanced functionality.

Maintenance

Cleaning

  • Regularly clean the earbuds and charging case with a soft, dry, lint-free cloth.
  • Remove any earwax or debris from the eartips and speaker mesh using a small, soft brush or cotton swab.
  • Do not use abrasive cleaners, alcohol, or chemical solvents.

Water Resistance

The QCY T13 ANC2 earphones are rated as Waterproof (IPX5). This means they are resistant to splashes of water from any direction, making them suitable for workouts and light rain. However, they are not designed for swimming, showering, or submersion in water. Avoid exposing them to high-pressure water or prolonged contact with water.

Storage

When not in use, always store the earphones in their charging case to protect them from damage and to keep them charged.

Troubleshooting

If you encounter issues with your QCY T13 ANC2 earphones, try the following solutions:

  • No Sound/Connection Issues:
    • Ensure the earbuds are charged.
    • Make sure Bluetooth is enabled on your device.
    • Check if "QCY T13 ANC2" is selected as the audio output on your device.
    • Try unpairing and re-pairing the earphones with your device.
    • Place both earbuds back into the charging case, close the lid, wait 5 seconds, then open the lid to reset the connection.
  • One Earbud Not Working:
    • Ensure both earbuds are charged.
    • Place both earbuds back in the charging case, close the lid, and then open it again.
    • Perform a factory reset (refer to the QCY app or manufacturer's website for specific instructions if a hard reset is needed beyond simple re-pairing).
  • Charging Problems:
    • Ensure the charging cable is securely connected to both the case and the power source.
    • Check for any debris or protective film on the earbud charging contacts or inside the charging case.
    • Try a different USB cable or power adapter.
  • ANC Not Functioning:
    • Ensure ANC is activated by double-tapping the left earbud.
    • Check for proper fit of the eartips to ensure a good seal in your ear canal.

Specifications

FeatureSpecification
ModelT13 ANC2
StyleIn-ear
MaterialABS
Weight41g (total, likely including case)
Battery Capacity (Case)380mAh
Total Battery LifeUp to 30 hours (with charging case)
Charging MethodCable (USB-C)
Bluetooth Version5.3
Maximum Wireless Range<10m
Driver Diameter10mm
Active Noise-CancellationYes
Sound IsolatingYes
With MicrophoneYes
Volume ControlYes (via touch controls)
Control ButtonYes (touch-sensitive)
Waterproof RatingIPX5
App SupportYes
OriginMainland China
Black QCY T13 ANC2 earbuds and charging case with '30 hour' text
The QCY T13 ANC2 offers up to 30 hours of total battery life with the charging case.

User Tips

  • Optimal Fit: Experiment with different eartip sizes to find the best fit for your ears. A good seal is crucial for effective noise cancellation and sound quality.
  • Remove Protective Film: Always remember to remove any protective film from the earbud charging contacts before first use to ensure proper charging.
  • QCY App: Download the official QCY app to unlock additional features, customize controls, and update firmware for the best experience.
  • Regular Cleaning: Keep your earbuds clean, especially the eartips and speaker mesh, to maintain hygiene and sound quality.
  • Case for Protection: Always store the earbuds in their charging case when not in use to prevent loss and damage.

Warranty and Support

Your QCY T13 ANC2 Wireless Earphones come with a standard manufacturer's warranty. Please refer to the warranty card included in your packaging or contact the seller/manufacturer for specific warranty terms and conditions.

For technical support, troubleshooting assistance, or warranty claims, please contact the authorized QCY distributor or the point of purchase. Ensure you have your proof of purchase and product model information readily available.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.