Introduction
This manual provides comprehensive instructions for the safe and efficient use, maintenance, and troubleshooting of your Laresar M3 Cordless Wet Dry Vacuum Cleaner Mop. Please read this manual thoroughly before operating the appliance and keep it for future reference.
The Laresar M3 is a versatile smart home appliance designed for wet and dry cleaning, featuring advanced technologies such as smart dirt detection, edge cleaning, and self-cleaning capabilities. It offers a powerful 13000Pa suction and a long runtime of up to 55 minutes, ensuring a thorough and convenient cleaning experience.
Important Safety Instructions
Please read the following precautions carefully before using this appliance:
- Use only indoors on non-carpeted floor surfaces such as vinyl, tile, sealed wood, etc. Be careful not to run over loose objects or carpet edges.
- Use only the battery pack and charger specified by Laresar. Using any other battery pack may cause personal injury and fire risk.
- Do not use this appliance to clean flammable or chemical products such as gasoline, strong acids, or strong alkalis; do not use to pick up sharp objects such as metal nails, glass fragments, and needles.
- Do not touch the charger and the plug with wet hands.
- Do not use this appliance without the filter.
- Do not use with a damaged power cable or plug. If this appliance has been dropped, damaged, left outdoors, dropped into water, or failed to work properly, please contact our service center.
- Be extra careful when cleaning on the stairs.
- Keep your hair, clothing, fingers, and all parts of your body away from openings and moving parts.
- Do not use this appliance when the water depth exceeds 5 mm.
- Turn off this appliance before making any adjustments, replacing accessories, or storing this appliance.
- This appliance can only be used, charged, and stored in a dry room where the temperature is higher than 4°C but lower than 35°C.
- If you accidentally drop the battery, liquid may run out of the battery. Avoid touching it. If touched accidentally, rinse with water. If liquid gets into your eyes, seek medical help.
- If this appliance overheats, makes abnormal noise, produces abnormal smell or leaks, stop using it immediately.
- For long-term storage, please turn off M3 and disconnect the power from the socket.
- Be sure to clean the dirty water tank after each use to avoid clogging, which will result in poor suction, motor overheating or shortened service life of this appliance.
- All data and technical descriptions in this manual are based on test results from Laresar laboratory tests and Laresar reserves the right of final interpretation.
Product Overview
Familiarize yourself with the components of your Laresar M3 vacuum cleaner.
Package Contents
The package includes the following items:
- Main Body (1 roller brush + 1 HEPA installed)
- Handle
- Charging Base
- HEPA Filter
- Cleaning Brush
- Adapter
Setup and Assembly
Assembly and Disassembly of the Main Unit
- Insert the end of the handle into the main unit port along the direction shown in the figure. Insert it to the bottom and hear a "Click". Moreover, keep the port flush with the schematic line of the handle to make sure the handle is tight and not loose. The installation is complete.
- To disassemble the main unit, use a hard object to stretch into the hole in the back of the cleaner body and press the spring, and pull out the handle upwards.
Clean Water Tank Installation
- Hold the cleaner body with one hand and push the clean water tank button with the other hand, and then pull the clean water tank outward to take it out.
- First put the bottom of the water tank into the opening on the back of the appliance, push the water tank gently, and the installation is successful when you hear a click.
Roller Brush Cover Assembly and Disassembly
- Grab the front handle while pressing the button. Press the button, and pull the roller brush cover upwards to remove it.
- Align the roller brush cover with the floor brush, press it down. The installation is complete when you hear a click.
Roller Brush Assembly and Disassembly
- Grab the side handle of the roller brush, pull it outward and remove the roller brush.
- Align the right end of the roller brush with the right end of the floor brush, push it to the right, and insert the left handle into the corresponding position to complete the installation.
Product Charging
- After use, place the cleaner vertically on the charging station, insert one end of the adapter into the charging dock, and connect the other end to a socket in the home. During charging, keep the cleaner upright and close to the toe of the wall to avoid tripping and other injuries.
- The power indicator flashes during charging.
- After the charging is completed, the power indicator is always on and will go out after 5 minutes.
Charging Reminders:
- Generally, 10-50% of the battery capacity is reserved when the product leaves the factory. It is recommended to fully charge the product when using it for the first time to ensure the effect and duration of use.
- Please fully charge the battery before use if it has not been fully charged for a long time.
- It takes 4 hours for the battery to be fully charged at room temperature. The actual charging time varies depending on the ambient temperature and voltage.
- After fully charged, if there is no other operation, the cleaner will automatically shut down and all indicator lights will be off.
- If the product is not used for a long time after purchase, please use the special charging dock provided by us to charge the battery for 3 hours every 3 months (without full charging).
Operating Instructions
Preparation
- Before use, please check whether the appliance is powered. If the power is insufficient, please charge it in time and use it after it is fully charged.
- The Power On defaults to the smart mode, and the appropriate mode may be selected according to the actual situation.
- Add water to the clean water tank:
- Remove the clean water tank.
- Open the rubber plug of the clean water tank and inject clean water (below 30°C) up to the water level.
- Close the clean water tank cover tightly and make sure it is tight and not loose.
- Install the clean water tank back to the appliance. You should hear a "Click" if done correctly.
Start To Work
- The appliance is equipped with a vertical ON button. Please tilt the appliance for use after startup. Do not recline the appliance more than 142° to protect against water leakage.
- Tilt the main unit and turn it on again.
Main Interface Function Display
The LED screen provides real-time information about the vacuum cleaner's status and selected modes.
- On/Off Button: Press the ON/OFF button to turn the cleaner on/off.
- Smart Mode: After startup, the cleaner is in the smart mode, and automatically senses the dirt on the ground and automatically adjusts the suction according to the dirt degree. The mode is suitable for daily cleaning in the home.
- Max Mode: Press the gear switch button, and switch the mode to the MAX mode. This mode is suitable for removing stubborn stains and water accumulation.
- Water Absorption Mode: This mode only absorbs water and is suitable for bathrooms to absorb excess water.
- Auto Cleaning: In the charging state, press the Auto Cleaning button, and the cleaner will automatically clean the roller brush and pipeline.
- Low Battery Reminder: If the battery capacity is less than 20%, the red aperture light above the "battery capacity" of the battery pack will flash. It is recommended to put the cleaner back into the charging dock for charging.
- Dirty Water Pouring Reminder: If the dirty water tank is full of dirty water, the dirty water tank indicator light of the cleaner will flash, and the cleaner will automatically shut down. Please pour the dirty water, reinstall the dirty water tank onto the cleaner, and then start the cleaner.
- Water Adding Reminder: If the water in the clear water tank is used up, the clean water tank indicator light of the cleaner will flash. Please shut down the cleaner and take down the clear water tank to add clear water. Reinstall the clear water tank onto the cleaner before starting the cleaner.
- Roller Brush Cleaning Reminder: If the roller brush is wound by hair and other objects, the floor brush indicator light of the cleaner will flash, and the cleaner will automatically shut down. Please remove the roller brush and clean it. Then reinstall the roller brush and the roller brush cover before starting the cleaner.
Voice Off & On
Requirement: The machine has to be in upright standby before the voice can be turned off or on.
Machine power on default is the voice on state. Long press the self-cleaning button for 3 seconds to turn off or on the voice.
Language Switch
Requirement: The machine has to be in upright standby before the language can be switched.
Long press the gear switching button for 3 seconds to trigger the voice switching function, then the voice announces the current language name, such as "English", all lights on the display breathe, then short press the function switching button to switch the language (switching order: English, German, French, Italian, Spanish).
Maintenance and Cleaning
Clean the Appliance
- Before cleaning, make sure the appliance is powered off.
- Wipe the appliance with water or neutral detergent. Be sure to wring out the cleaning cloth before wiping, and do not let water flow into the appliance.
Clean the Dirty Water Tank
- When the dirty water tank is full or the appliance is shut down, remove the dirty water tank.
- Remove the dirty water from the dirty water tank and wash the dirty water tank with clean water.
- Clean the dirty water tank cover, HEPA and solid-liquid separator.
- After the dirty water tank cover and HEPA are dried, assemble them and put them back into the appliance.
Auto Cleaning
The Laresar M3 features a one-click self-cleaning function.
- Please put the appliance back to the base in time after use.
- Make sure that the water volume of the clean water tank exceeds the auto cleaning minimum water level, and the dirty water tank has no dirty water. Then press the auto cleaning button, and the machine will start auto cleaning.
- After auto cleaning, please clean the dirty water tank and dry the roller brush and HEPA in the air.
Clean the Suction Port of the Floor Brush and the Roller Brush Cover
- Clean the suction port of the floor brush with a cleaning brush.
- Clean the roller brush cover with a cleaning brush.
- After cleaning, reinstall the roller brush and its cover onto the machine.
Tips for Use:
- It is recommended to clean the roller brush, roller brush cover, suction port and pipeline regularly.
- After the heavy oil stains are removed by the roller brush, it is recommended to start the auto cleaning function many times to clean the roller brush and pipeline. You can also take down the roller brush after auto cleaning and soak or wash the roller brush with warm water.
Troubleshooting
If you encounter any issues with your Laresar M3, refer to the table below for possible causes and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| The roller brush is not working | The roller brush is blocked | Please clean the roller brush |
| The roller brush is worn | Please Contact Customer Service | |
| Abnormal operation of the vacuum cleaner | The drive belt is worn | Please Contact Customer Service |
| The roller brush, roller brush cover and dirty water tank are not installed in place | Please reinstall them | |
| The suction port or pipe is blocked | Please clean the suction port or pipe | |
| The dirty water tank has the specified capacity | Please take out the dirty water tank to pour out wastewater | |
| Abnormal noise when the appliance is running | The roller brush is entangled by objects such as hair | Please clean the roller brush |
| The floor brush is not installed in place | Please reinstall the floor brush | |
| No water comes out when the appliance is working | Water shortage in the clean water tank | Add water to the clean water tank |
| The clean water tank is not installed in place | Please reinstall it | |
| Water leakage at the bottom of the roller brush | The HEPA is not dried after cleaning | Please dry the HEPA |
| The HEPA is not installed | Please install the HEPA | |
| Auto cleaning fails to start | The dirty water tank or HEPA is not installed | Please install the dirty water tank or HEPA |
| The water pump is damaged | Please contact the authorized after-sales service center to replace the water pump | |
| No voice function | The voice function is turned off | Press and hold the gear switch key for 3 seconds in the Power On state |
| The display is not lit and there is no display | The display is damaged | Please Contact Customer Service |
Product Specifications
Detailed technical specifications for the Laresar M3 Cordless Wet Dry Vacuum Cleaner Mop.
| Attribute | Value |
|---|---|
| Product Model | M3 |
| Brand Name | LARESAR |
| Function | Wet and Dry |
| Power (W) | 250w |
| Rated Power | 230W |
| Voltage | 110V-240V |
| Plug and Voltage | 100~240 Volts 50Hz European Plug |
| Battery Type | Li-ion / Lithium Battery |
| Battery Capacity | 29.6V*2500mAh(74Wh) |
| Charging | 3-hour Fast Charging |
| Runtime | 55 Minutes (ECO Mode) |
| Suction Power | 13000Pa(Maximum) |
| Dust Box Capacity (L) | 0.6-1 L |
| Dust Storage Type | Dust Bucket |
| Filter Type | HEPA / Washable HEPA Filter |
| Liquid tank volume | <3l |
| Clean Water Tank Capacity | 650mL |
| Dirty Water Tank Capacity | 500mL |
| Number of operating modes | 3-4 (Vac Mode / Max Mode / Smart Mode) |
| Turbo Brush | Yes |
| Special Suction Nozzle | Wiping & Absorbing Ground Brush / Edge Cleaning Brush |
| LCD | Yes / LED Screen |
| Cleaning Route | Random Type |
| Bag Or Bagless | Bagless |
| Cord Length (m) | WireLess |
| Timing Reservation | No |
| Installation | Upright |
| Certification | ce, ROHS, CE |
| Origin | Mainland China |
| Weight | 3-6 kg |
| Product Size & Weight | 111.5*28.0*22.5cm / 4.0kg |
| Package Size & Weight | 33.8*30.8*70.5cm / 7.27kg |
| Appliance Type | Wireless Vacuum Cleaner, Cordless Upright Vertical Handheld Smart Home Appliance |
| Special Features 1 | Smart Dirt Detection(Automatically Adjust Suction) |
| Special Features 2 | Water Suction Mode(In this mode, it only absorbs water) |
| Special Features 3 | Low Center of Gravity Tank Design(Effectively reduces fatigue) |
| Special Features 4 | Self-propelled Power Traction |
| Special Features 5 | Intelligent Voice Guidance |
| Common Waste Cleanup | Such as ketchup, noodles, eggs, and water stains |
Warranty and Support
2-Year Limited Warranty
Your Laresar machine has a 2-year warranty against original defects in material and workmanship when used for private household purposes in accordance with the Laresar Instruction Manual.
This warranty provides, at no extra cost to you, all labor and parts necessary to ensure your machine is in proper operating condition during the warranty period.
What is Covered?
- According to the requirements outlined in this instruction manual, subject to the following conditions and exclusions.
- Only applies to purchases made from authorized retailers of Laresar.
- This warranty will only be valid if the machine is used in the country in which it was sold.
What is NOT Covered?
Laresar shall not be liable for costs, damages, or repairs incurred as a result of:
- Machines purchased from an unauthorized dealer.
- Careless operation or handling, misuse, abuse, and/or lack of maintenance or use not in accordance with the Laresar Instruction Manual.
- The machines are used for commercial or rental purposes in addition to normal domestic use.
- Use of parts not in accordance with the Laresar Instruction Manual.
- Use of parts and accessories other than those produced or recommended by Laresar.
- External factors are unrelated to product quality and use, like accidental water damage.
- Repairs or alterations carried out by unauthorized parties or agents.
- Normal wear and tear, including Water Tank, Filter, HEPA, Main Brush, Side Brush, Power Cord (or where external damage or abuse is diagnosed), carpet or floor damage due to use not in accordance with manufacturer's instructions or failure to turn the brush roller off when necessary.
- Reduction in battery discharge time due to battery age or use.
How to Claim?
- Please keep your proof of purchase. To make a claim under our Limited Warranty, you need to provide your original purchase receipt with the purchase date and order number on it.
- All work will be carried out by Laresar or its authorized agency.
- Any replaced defective parts will become the property of Laresar.
- Service under this warranty will not extend the period of this warranty.
Customer Support
If your machine is not functioning properly, or you still have any questions after reading this manual carefully, please feel free to contact us. We will try our best to provide you with a satisfactory solution.
Email: iputure@outlook.com
You can also refer to the official user manual PDF for more detailed information: Laresar M3 User Manual (PDF).
Product Videos
Official Product Overview
This video provides an overview of the Laresar M3 Wet & Dry Vacuum Cleaner's features and operation.
Cleaning Demonstration (Polish)
This video, in Polish, demonstrates the Laresar M3's cleaning capabilities, including handling spills and the self-cleaning process. It shows how to empty the dirty water tank and clean the roller brush.
