1. Product Overview
This manual provides instructions for the Woodpecker DTE Dental Ultrasonic Scaler Handpieces. These handpieces are designed for professional dental use, offering efficient and reliable performance for various scaling procedures. They are 100% original Woodpecker products, manufactured to high standards and CE certified.
Key Features:
- Material: High-quality Metal construction.
- Detachable Design: Allows for easy cleaning and sterilization.
- Autoclavable: Can be sterilized at 135℃ and 0.22Mpa pressure.
- LED Light (select models): HW-5L, HW-6L, and HD-7L models feature integrated LED lighting for enhanced visibility during procedures.
- Wide Compatibility: Compatible with various ultrasonic scaler units from Woodpecker UDS series, EMS, NSK, SATELEC, and ACTEON.

2. Setup and Installation
Before initial use, ensure all components are clean and sterilized according to the maintenance guidelines. Verify compatibility with your existing ultrasonic scaler unit.
2.1 Handpiece Compatibility:
- HW-3H Handpiece: Compatible with Woodpecker UDS-N2, UDS-A, UDS-E, UDS-K, UDS-L, UDS-P series.
- HW-5L LED Handpiece: Compatible with Woodpecker UDS-A LED, UDS-E LED, UDS-L LED, UDS-K LED, UDS-P LED, UDS-N2 LED, UDS-N3 LED series.
- HW-6L LED Handpiece: Compatible with Woodpecker U600 LED, U6 LED, UDS-N6 LED series.
- HD-7L LED Handpiece: Compatible with Woodpecker D2 LED, D3 LED, D5 LED, D6 LED, D7 LED, V2 LED, V3 LED series, SATELEC ACTEON, and NSK tips.
- HD-7H Handpiece: Compatible with Woodpecker DTE-V2, D2/V3 D3/D5/D6/D7 series, SATELEC tips.
2.2 Connecting the Handpiece:
- Ensure the scaler unit is powered off.
- Align the connector of the handpiece or cable tube with the corresponding port on your ultrasonic scaler unit.
- Gently push and twist until the handpiece is securely attached. Do not force the connection.
- For models with separate cable tubes (e.g., Cable Tube-5L, Cable Tube-3H, Cable Tube-7L, Cable Tube-7H), connect the handpiece to one end of the tube and the scaler unit to the other.


3. Operating Instructions
These handpieces are designed for dental scaling procedures. Always follow standard dental protocols and safety guidelines during operation.
3.1 General Operation:
- Attach the desired scaler tip (e.g., TD-1L, TW-1L) securely to the handpiece.
- Ensure the handpiece is properly connected to the ultrasonic scaler unit.
- Power on the ultrasonic scaler unit and adjust settings (power, water flow) as required for the procedure.
- For LED models (HW-5L, HW-6L, HD-7L), the integrated LED light will illuminate upon activation, providing clear visibility of the treatment area.
- Perform scaling procedures with appropriate technique and patient care.


4. Maintenance and Sterilization
Proper maintenance and sterilization are crucial for the longevity and safe operation of your handpiece.
4.1 Cleaning:
- After each use, detach the handpiece and scaler tip from the unit.
- Remove any visible debris or biological material using a soft brush and appropriate cleaning solution.
- Rinse thoroughly with distilled water.
4.2 Sterilization:
The handpieces and tips are autoclavable. Follow these guidelines for sterilization:
- Autoclave Temperature: 135℃ (275°F)
- Autoclave Pressure: 0.22 Mpa (32 psi)
- Ensure the handpiece and tips are thoroughly dried before autoclaving.
- Place items in appropriate sterilization pouches or trays.
- Follow your autoclave manufacturer's instructions for cycle times and loading.


5. Troubleshooting
If you encounter issues with your handpiece, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Handpiece not working / No vibration | Loose connection; Incompatible scaler unit; Damaged handpiece/cable; Worn-out tip. | Ensure handpiece/cable is securely connected. Verify compatibility with your scaler unit. Replace the scaler tip if worn. If issues persist, contact support. |
| LED light not illuminating (for LED models) | Faulty LED; Power issue from scaler unit. | Check if the scaler unit is providing power correctly. If the LED remains off, the handpiece may require service. Note that HD-7H and HW-3H models do not have LED lights. |
| Water leakage | Loose tip; Damaged O-rings. | Ensure the scaler tip is tightened correctly. Inspect and replace O-rings if damaged. |
User Tips:
- Always confirm the authenticity of your Woodpecker product upon receipt to ensure optimal performance and safety.
- Regularly inspect scaler tips for wear and tear. Replacing tips promptly can prevent performance issues.
- Ensure your scaler unit is compatible with the specific handpiece model you are using.
6. Specifications
| Attribute | Detail |
|---|---|
| Brand Name | Woodpecker / YOYADENT |
| Model Numbers | HW-3H, HW-5L, HW-6L, HD-7L, HD-7H, TD-1L, TW-1L |
| Product Type | Dental Ultrasonic Scaler Handpiece |
| Material | Metal |
| Hand Instrument | Yes |
| High-concerned chemical | None |
| Commodity Quality Certification | CE |
| Autoclavable Temperature | 135℃ |
| Autoclavable Pressure | 0.22 Mpa |
| Origin | Mainland China |
7. Warranty and Support
These Woodpecker DTE Dental Ultrasonic Scaler Handpieces are supplied brand new directly from the factory, ensuring genuine quality. For any questions regarding product functionality, compatibility, or potential defects, please contact your point of purchase or the manufacturer's authorized service center.
It is recommended to retain your purchase receipt for any warranty claims. Specific warranty terms and conditions may vary by region and distributor.