EPever Tracer AN G3/G3 BLE series

Contents

EPEVER MPPT Tracer AN G3/G3 BLE Series Solar Charge Controller User Manual

Models: Tracer1206AN, Tracer1210AN, Tracer2206AN, Tracer2210AN, Tracer3210AN, Tracer4210AN (G3/G3 BLE variants)

1. Important Safety Instructions

Please reserve this manual for future review. This manual contains safety, installation, and operation instructions for the Tracer-AN G3/Tracer-AN G3 BLE series MPPT solar controller ("controller" referred to in this manual).

  • Read all the instructions and warnings carefully in the manual before installation.
  • No user-serviceable components inside the controller; please do not disassemble or attempt to repair the controller.
  • Mount the controller indoors. Avoid exposure to the components and do not allow water to enter the controller.
  • Install the controller in a well-ventilated place; the controller's heat sink may become hot during operation.
  • We suggest installing appropriate external fast-acting fuses/breakers.
  • Disconnect PV array connections and the battery fast-acting fuse/breakers before controller installation and adjustment.
  • Power connections must remain tight to avoid excessive heating from a loose connection.

WARNING:

Do not install the controller in humid, high salt spray, corrosion, greasy, flammable, explosive, dust accumulative, or other severe environments.

2. Disclaimers

The warranty does not apply to the following conditions:

  • Damage caused by improper use or inappropriate environment (such as humid, high salt spray, corrosion, greasy, flammable, explosive, dust accumulative, or other severe environments).
  • The actual current/voltage/power exceeds the limit value of the controller.
  • Damage caused by working temperature exceeding the rated range.
  • Arc, fire, explosion, and other accidents caused by failure to follow the controller stickers or manual instructions.
  • Unauthorized dismantling or attempted repair.
  • Damage caused by force majeure.
  • Damage occurred during transportation or handling.

3. Product Overview and Features

The Tracer-AN G3/Tracer-AN G3 BLE series controllers are designed with advanced MPPT control algorithms to minimize power loss and maximize energy harvesting from PV arrays. The G3 BLE series includes a built-in Bluetooth module for convenient parameter adjustment via a phone app.

Key Features:

  • High quality and low failure rate components for extended service life.
  • Advanced MPPT technology with >99.5% tracking efficiency.
  • Accurate multi-peak maximum power point recognition.
  • Wider MPP running voltage to optimize PV utilization.
  • Maximum DC/DC conversion efficiency of 98%.
  • Support for multiple battery types, including lithium batteries.
  • Stable self-activation function for lithium batteries.
  • Adjustable battery voltage parameters via LCD.
  • Battery temperature compensation.
  • Charging power and current limit to rated values.
  • Real-time energy statistics function.
  • Automatic charging power reduction for over-temperature.
  • Built-in Bluetooth (G3 BLE series) for app-based settings.
  • RS485 communication interface with optional 4G or Wi-Fi modules.
  • Standard Modbus communication protocol.
  • Power protection chip for 5VDC/200mA output with over-current and short-circuit protections.
  • Setting parameters via PC software, APP, or remote meter.
  • Constant voltage output function.
  • Comprehensive electronic protections.
  • Multiple load work modes.
  • Low self-consumption (<10mA).
  • Operation at full load without charging power reduced in the working temperature range.

Product Characteristics Diagram

Diagram of EPEVER MPPT Solar Charge Controller with labeled components
Figure 1-1: Product Characteristics. Key components include: (1) SELECT button, (2) RTS interface, (3) PV Terminals, (4) Battery Terminals, (5) Load Terminals, (6) RS485 port, (7) Mounting Hole, (8) ENTER button, (9) LCD.

4. Setup and Installation

4.1 Naming Rules

The model numbers follow a specific naming convention:

  • Tracer X Y Z AN G3: X = Rated charging & discharging current (e.g., 4 for 40A), Y = Battery rated voltage (e.g., 2 for 12/24VDC), Z = PV maximum open-circuit voltage (e.g., 10 for 100V), AN = Common negative system, G3 = 3rd generation product.
  • Tracer X Y Z AN G3 BLE: Same as above, with BLE indicating a built-in Bluetooth module.

4.2 Connection Diagram

The controller supports both no-battery mode (direct connection to inverter) and battery mode.

Schematic Wiring Diagram for Solar Charge Controller
Figure 2-2: Schematic Wiring Diagram. Shows connections for Solar Panels, Battery, DC Loads, and Inverter/AC Loads.

No-battery Mode:

When there is no battery, the Tracer-AN G3/Tracer-AN G3 BLE series can be directly connected to the inverter. The inverter shall be connected to the battery terminals of the controller and meets the following conditions:

  1. For high-frequency inverter: PV input power > (load output power ÷ inverter conversion efficiency ÷ controller conversion efficiency)
  2. For power frequency inverter: PV input power > (load output power ÷ inverter conversion efficiency ÷ controller conversion efficiency ÷ 2)

Battery Mode:

Connection Diagram for Solar Charge Controller in Battery Mode
Connection Diagram for Solar Charge Controller in Battery Mode, including PV array, battery, and loads.

4.3 Requirements for the PV Array

The controller needs to suit various types of PV modules and maximize solar energy conversion. The serial connection (string) of PV modules depends on the open-circuit voltage (Voc) and maximum power point voltage (VMPP) of the MPPT controller.

PV Array Configuration (Tracer1206/2206AN G3/BLE)
System voltage36cell (Voc< 23V)48cell (Voc< 31V)54cell (Voc< 34V)60cell (Voc< 38V)
Max.BestMax.BestMax.BestMax.Best
12V22111111
24V22------

Note: These parameters are calculated under STC (Standard Test Condition: module temperature 25°C, air mass 1.5, irradiance 1000W/m²).

PV Array Configuration (Tracer1210/2210/3210/4210AN G3/BLE)
System voltage36cell (Voc< 23V)48cell (Voc< 31V)54cell (Voc< 34V)60cell (Voc< 38V)
Max.BestMax.BestMax.BestMax.Best
12V42212121
24V43222222

Note: These parameters are calculated under STC (Standard Test Condition: module temperature 25°C, air mass 1.5, irradiance 1000W/m²).

4.4 Wire Size

The wiring and installation methods must conform to national and local electrical code requirements. The minimum wire size can be calculated from the PV array's short circuit current (ISC).

PV Wire Size Recommendations
ModelMax. PV input currentMax. PV wire size
Tracer1206/1210AN G3/BLE10A4mm²/12AWG
Tracer2206/2210AN G3/BLE20A6mm²/10AWG
Tracer3210AN G3/BLE30A10mm²/8AWG
Tracer4210AN G3/BLE40A16mm²/6AWG

CAUTION:

The total voltage must not exceed the PV maximum open-circuit voltage when the PV modules are connected in series. The PV maximum open-circuit voltage is 46V (Tracer**06AN G3/BLE) or 92V (Tracer**10AN G3/BLE) at 25°C environment temperature.

Battery and Load Wire Size Recommendations
ModelRated charge currentRated discharge currentBattery wire sizeLoad wire size
Tracer1206/1210AN G3/BLE10A10A4mm²/12AWG4mm²/12AWG
Tracer2206/2210AN G3/BLE20A20A6mm²/10AWG6mm²/10AWG
Tracer3210AN G3/BLE30A30A10mm²/8AWG10mm²/8AWG
Tracer4210AN G3/BLE40A40A16mm²/6AWG16mm²/6AWG

CAUTION:

  • The wire size is only for reference. For long distances between the PV array and the controller or between the controller and the battery, use larger wires to reduce voltage drop and improve performance.
  • The recommended wire is selected for the battery according to the conditions that its terminals are not connected to any additional inverter.

4.5 Mounting

Installation procedures:

Step 1: Determine the installation location and heat-dissipation space

Mounting diagram showing required clearances around the controller
Figure 2-1: Mounting. Ensure at least 150mm clearance above and below the controller for proper airflow.

WARNING:

  • Risk of explosion! Never install the controller in a sealed enclosure with flooded batteries! Do not install the controller in a confined area where battery gas can accumulate.
  • Risk of electric shock! The PV array may generate a high open-circuit voltage when wiring the PV modules. Disconnect the breaker or fast-acting fuse first, and be careful when wiring.

CAUTION:

The controller requires at least 150mm of clearance above and below for proper airflow. Ventilation is highly recommended if mounted in an enclosure.

Step 2: Connect the system in the order of battery → load → PV array, following the schematic wiring diagram, and disconnect the system in the reverse order.

4.6 Grounding

Tracer-AN G3/Tracer-AN G3 BLE series are common-negative controllers. Negative terminals of the PV array, the battery, and the load can be grounded simultaneously, or any negative terminal can be grounded. However, the grounding terminal on its shell must be grounded to shield electromagnetic interference and avoid electric shock.

CAUTION:

It is recommended to use a common-negative controller for common-negative systems, such as the RV system. The controller may be damaged if a common-positive controller is used and the positive electrode is grounded in the common-negative system.

4.7 Connect Accessories

Temperature Sensor:

Connect one end of the remote temperature sensor cable to the interface and place the other end close to the battery.

CAUTION:

If the remote temperature sensor is not connected or damaged, the controller will charge or discharge the battery at the default temperature setting of 25 °C (no temperature compensation).

RS485 Communication:

Connect the accessories for RS485 communication. The internal circuit of the RS485 port has no isolation design. Connecting an RS485 communication isolator to the port is recommended before communicating.

Diagram showing PC connection to controller via RS485 to USB cable
PC connection to controller via RS485 to USB cable for parameter setting.

4.8 Power On the Controller

Connect the battery fast-acting fuse to power the controller. Check the battery indicator status (the controller operates normally when the indicator is lit green). Connect the fast-acting fuse and circuit breaker of the load and PV array. The system will then operate in preprogrammed mode.

CAUTION:

If the controller is not operating properly or the battery indicator shows an abnormality, please refer to the Troubleshooting section.

5. Operating Instructions

5.1 Maximum Power Point Tracking (MPPT) Technology

Due to the nonlinear characteristics of the solar array, there is a maximum energy output point (Max Power Point) on its curve. Our MPPT algorithm continuously compares and adjusts the operating points to locate the array's maximum power point, boosting the battery charge current. This process is fully automatic and does not require user adjustment.

Graph showing Current Curve, Power Curve, and Actual Point for MPPT
Figure 1-2: Maximum Power Point Tracking Technology. Illustrates how MPPT tracks the maximum power point compared to traditional operating ranges.
Graph showing Multi-MPP Curve
Figure 1-3: Multi-MPP Curve. Shows how the controller handles multiple power peaks to find the true maximum power point.

5.2 Battery Charging Stages

The controller employs a three-stage battery charging algorithm: Bulk Charging, Constant Charging (Equalize and Boost), and Float Charging. This extends battery lifespan and improves system performance.

Graph illustrating the three battery charging stages: Bulk, Constant, and Float
Figure 1-4: Battery charging stage curve. Shows battery voltage and current over time during different charging phases.

A) Bulk Charging:

The controller operates in constant current mode, delivering maximum current until the battery voltage reaches the constant voltage set point.

B) Constant Charging (Equalize and Boost):

Once the constant voltage set point is reached, the controller enters constant charging mode. The charging current gradually drops. Equalize charging occurs on the 28th of each month. Boost charging typically lasts 2 hours (adjustable).

WARNING (Equalize Charging):

Explosive Risk! Equalizing flooded batteries produces explosive gases; ensure good ventilation. Equipment damage! Equalization may increase battery voltage, damaging sensitive DC loads. Over-charging can damage battery plates. Review battery requirements carefully.

C) Float Charging:

After constant charging, the controller reduces battery voltage to the float charging preset voltage. In this stage, loads can obtain almost all power from the solar panel. If load power exceeds solar array power, the controller will exit float charging and re-enter bulk charging if battery voltage drops below the boost voltage reconnect voltage.

5.3 LCD Interface

The LCD displays system information. Ensure the viewing angle is within 90° for clear visibility.

Buttons:

  • ENTER button: Used to turn load On/Off in manual mode, clear faults, and confirm settings. Hold for 5s to enter setting mode.
  • SELECT button: Used to browse modes and set parameters.

Status Description:

NameIconStatus
PV array☀️Day
🌙Night
🚫No charge
Battery🔋Battery capacity, In charging
📊Battery Voltage, Current, Temperature
⚙️Battery type
Load💡Load ON
🚫💡Load OFF
⚡Current/Consumed energy/Load mode

Error Codes:

StatusIconInstruction
Battery over-discharged⚠️🔋Battery level shows empty, battery frame blink, fault icon blink
Battery over voltage⚠️🔋Battery level shows full, battery frame blink, fault icon blink
Battery overheating⚠️🔋Battery level shows current value, battery frame blink, fault icon blink
Load failure⚠️💡Overload, Load short circuit

5.4 Setting Parameters

Clear Generated Energy:

  1. Press the ENTER button and hold 5s under the PV-generated energy interface; the value will flash.
  2. Press the ENTER button again to clear the generated energy.

Switch Battery Temperature Unit:

Press the button and hold for 5s under the battery temperature interface to switch the temperature unit.

Battery Type:

The controller supports Sealed (default), Gel, Flooded, LiFePO4, Li(NiCoMn)O2, and User-defined battery types.

Local Setting via LCD:

  1. Press SELECT to jump to the battery voltage interface.
  2. Press and hold ENTER until the battery-type interface flashes.
  3. Press SELECT to change the battery type.
  4. Press ENTER to confirm.

Remote Setting via PC Software:

Connect the controller's RJ45 port to the PC's USB interface via a USB to RS485 cable. When selecting "USE" battery type, set voltage parameters via PC software.

Remote Setting via APP:

Connect the controller to an external WiFi 2.4G adapter or Bluetooth adapter (or use built-in Bluetooth for G3 BLE series). Set voltage parameters via the APP after selecting "USE" battery type.

Load Modes:

The controller offers various load modes, including Light ON/OFF, Test mode, and Manual mode (Always ON). These can be set via PC software, APP, or a remote meter (MT50).

Load Mode List
Mode (Timer 1)DescriptionMode (Timer 2)Description
100Light ON/OFF2 nDisabled
101Load on for 1 hour since sunset201Load on for 1 hour before sunrise
102Load on for 2 hours since sunset202Load on for 2 hours before sunrise
103~113Load on for 3~13 hours since sunset203~213Load on for 3~13 hours before sunrise
114Load on for 14 hours since sunset214Load on for 14 hours before sunrise
115Load on for 15 hours since sunset215Load on for 15 hours before sunrise
116Test mode2 nDisabled
117Manual mode (Default load ON)
118Always ON mode (24-hour power supply)2 nDisabled

6. Maintenance

The following inspections and maintenance tasks are recommended at least twice yearly for good performance:

  • Ensure no block on airflow around the controller. Clear up any dirt and fragments on the radiator.
  • Check all naked wires to ensure insulation is not damaged by sun exposure, frictional wear, dryness, insects or rats, etc. Repair or replace some wires if necessary.
  • Verify the indicator display is consistent with the actual operation. Pay attention to any troubleshooting or error conditions. Take necessary corrective action.
  • Confirm that terminals have no corrosion, insulation damaged, high temperature, burnt/discolored sign, and tighten terminal screws to the suggested torque.
  • Clear up dirt, nesting insects, and corrosion in time.
  • Check and confirm that the lightning arrester is in good condition. Replace a new one in time to avoid damaging the controller and other equipment.

CAUTION:

Risk of electric shock! Ensure the power is turned off before performing any maintenance operations.

7. Troubleshooting

7.1 Protection Functions

The controller includes various protection mechanisms:

  • PV Over Current: Controller charges at rated current/power if PV input exceeds it.
  • PV Short-circuit: Controller is not damaged if PV array is short-circuited when not charging. WARNING: Do not short-circuit PV array during charging.
  • PV Reverse Polarity: Controller may not be damaged and resumes work after correcting mis-wiring. CAUTION: Controller may be damaged if PV array is reversed and its actual power is 1.5 times the rated power.
  • Night Reverse Charging: Prevents battery discharge to PV module at night.
  • Battery Reverse Protection: Correct wire connection to resume work. WARNING: Controller will be damaged if PV connection is correct and battery connection is reversed!
  • Battery Over Voltage: PV array stops charging when battery voltage reaches over voltage disconnect voltage.
  • Battery Over-discharging: Battery discharge stops when voltage is lower than low voltage disconnect voltage.
  • Battery Overheating: Stops charging when battery temperature exceeds 65°C, resumes below 55°C.
  • Lithium Battery Low Temperature: Stops charging/discharging if temperature is below Low-Temperature Protection Threshold (LTPT, default 0°C, adjustable).
  • Load Short Circuit: Controller cuts off output, attempts to resume five times automatically (with delays). Can be reset by pressing Load button, restarting controller, or night-to-day change.
  • Overload Protection: Controller cuts off output after a delay if load current exceeds 1.05 times rating, attempts to resume five times automatically (with delays). Can be reset by pressing Load button, restarting controller, or night-to-day change.
  • Device Overheating: Stops working if internal temperature exceeds 85°C, resumes below 75°C.
  • TVS High Voltage Transients: Internal circuitry protects against high-voltage surge pulses with less energy. External surge arrester recommended in lightning-prone areas.

7.2 Troubleshooting Table

FaultsPossible CauseTroubleshooting
PV array open-circuitNo direct sunlight or incorrect connection.Confirm PV array connection is correct and tight.
Battery voltage is lower than 8VBattery deeply discharged or controller not working.Check battery voltage (must be at least 8V to activate controller).
Battery over voltageBattery voltage higher than OVD.Disconnect PV array connection.
Battery over-dischargedBattery voltage below LVR.Recharge battery using other methods. Load will recover when battery voltage is restored.
Battery overheatingBattery temperature above 55°C.Controller will resume when temperature declines below 55°C.
OverloadExcessive load connected.Reduce number of electric devices. Restart controller or press button to clear faults.
Load short-circuitShort circuit on load side.Check load connections carefully, clear fault. Restart controller or press button to clear faults.

8. Specifications

8.1 Electrical Parameters

Electrical Parameters for Tracer AN G3/G3 BLE Series
ParameterTracer1206AN/1210AN G3/BLETracer2206AN/2210AN G3/BLETracer3210AN G3/BLETracer4210AN G3/BLE
Battery Rated Voltage12/24VDC Auto-recognition
Rated Charging Current10A20A30A40A
Rated Discharge Current10A20A30A40A
Controller Work Voltage Range8~31V
PV Maximum Open-circuit Voltage60V (46V at 25°C)100V (92V at 25°C)
MPPT Voltage Range(Battery voltage +2V)~36V(Battery voltage +2V)~72V
Rated Charging Power130W/12V, 260W/24V260W/12V, 520W/24V390W/12V, 780W/24V520W/12V, 1040W/24V
Static Losses<8mA(12V), <5mA(24V)
Discharge-circuit Voltage Drop≤0.23V
Temperature Compensation-3mV/°C/2V (Default)
Grounding TypeCommon negative
RS485 Port5VDC/200mA(RJ45)
LCD Backlight TimeDefault:60S, Range:0~999S (0 seconds: backlight is ON all the time)
Work Temperature Range-25°C~+45°C (100% loads working)
Storage Temperature Range-20°C~+70°C
Relative Humidity< 95% (N.C.)
EnclosureIP30

8.2 Mechanical Parameters

Mechanical Parameters for Tracer AN G3/G3 BLE Series
ModelTracer1206/1210AN G3/BLETracer2206/2210AN G3/BLETracer3210AN G3/BLETracer4210AN G3/BLE
Dimension (L x W x H)172x139x44mm220x154x52mm228x164x55mm252x180x63mm
Mounting Size (L x W)124x130mm170x145mm170x155mm204x171mm
Mounting Hole SizeΦ5mm
Terminal12AWG(4mm²)6AWG(16mm²)6AWG(16mm²)6AWG(16mm²)
Recommended Wire Size12AWG(4mm²)10AWG(6mm²)8AWG(10mm²)6AWG(16mm²)
Net Weight0.57kg0.94kg1.26kg1.65kg

8.3 Conversion Efficiency Curves

Detailed conversion efficiency curves for various PV array maximum power point voltages and system voltages are available in the full PDF manual. These graphs illustrate the controller's performance under different operating conditions.

9. User Tips

  • Ventilation is Key: Always ensure adequate airflow around the controller, especially in enclosed spaces, to prevent overheating and maintain optimal performance.
  • Secure Connections: Regularly check all wire connections to ensure they are tight and free from corrosion to prevent heat buildup and potential hazards.
  • Battery Type Setting: Accurately set your battery type in the controller settings (via LCD, PC, or APP) to ensure proper charging and prolong battery life. For custom battery parameters, use the "USE" setting.
  • Monitor Performance: Utilize the LCD interface or the EPEVER APP to monitor real-time energy statistics and system status. This helps in early detection of any issues.

10. Warranty and Support

For detailed warranty information and conditions, please refer to the Disclaimers section of this manual. The manufacturer's warranty typically covers defects in materials and workmanship under normal use. Damage resulting from improper installation, unauthorized modification, or operation outside specified parameters may void the warranty.

For further assistance, technical support, or to access the full user manual PDF, please refer to the official EPEVER website or contact your vendor. The user manual (PDF) can be viewed here.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.