1. Product Overview
The Flysky X6B is a compact and versatile 6-channel two-way receiver designed for multi-rotor aircraft, FPV racing drones, airplanes, and helicopters. It utilizes the advanced AFHDS 2A (Automatic Frequency Hopping Digital System) protocol and features dual omnidirectional antennas for superior noise reduction and reliable signal reception. The receiver supports multiple output types including PWM, PPM, and i-BUS, offering flexibility for various control setups.

Figure 1: Flysky X6B Receiver with dual antennas.

Figure 2: The compact size of the X6B receiver.
2. Specifications
| Feature | Description |
|---|---|
| Channels | 6 (PWM), up to 18 (i-BUS) |
| RF Range | 2.408-2.475GHz |
| RF Channel | 135 |
| RX Sensitivity | -92dBm |
| 2.4G System | AFHDS 2A |
| Modulation Type | GFSK |
| DSC Port | PPM/i-BUS/S.BUS |
| Power Input | 4.0-8.4V |
| Operating Current | 40mA |
| Channel Delay | <15ms |
| Size | 36*22*7.5mm |
| Weight | 5g |
| Antenna Length | 26mm (excluding brass contacts) |
| Compatible Transmitters | FS-i10, FS-i8, FS-i6, FS-i6S, FS-i6X, FS-i4, FS-i4X (AFHDS 2A series) |

Figure 3: Detailed specifications and compatible transmitters for the X6B receiver.
3. Setup and Connections
3.1 Package Contents
- 1x Flysky FS-X6B Receiver
- Connecting cables (various types for PWM, PPM, i-BUS)

Figure 4: The FS-X6B receiver and its accompanying cables.
3.2 Port Descriptions

Figure 5: X6B receiver board showing port labels.
- PWM Signal Port (CH1-CH6): Connects to flight controller or servos for individual channel PWM output. Includes GND and VCC pins.
- PPM Signal Port: Outputs a standard PPM signal, often used for flight controllers that accept a single-wire input for multiple channels.
- i-BUS Signal Port: Outputs an i-BUS signal, supporting up to 18 channels through a single wire. This is a digital serial protocol.
- Voltage Sensor Port: External power sensor input (1S-4S connector) for voltage monitoring, supporting 0 to +18V.
- BIND Button: Used to initiate the binding process with a compatible transmitter.
- UPDATE Button: Used for firmware updates.
- ANT1/ANT2: Connectors for the dual omnidirectional antennas.
3.3 Connecting Cables

Figure 6: Example of cables connected to the X6B receiver ports.
Video 1: Demonstration of connecting cables to the Flysky X6B receiver.
Ensure all connections are secure and correctly oriented. Refer to your flight controller or servo documentation for specific wiring diagrams.
4. Binding Procedure
To establish communication between your Flysky transmitter and the X6B receiver, you must perform a binding procedure. Ensure your transmitter is a compatible AFHDS 2A model (e.g., FS-i10, FS-i6, FS-i6X).
- Prepare Transmitter: Refer to your specific Flysky transmitter's user manual for instructions on how to put it into binding mode. This usually involves navigating through the menu system.
- Power on Receiver in Bind Mode: While holding down the BIND button on the X6B receiver, power on the receiver. The receiver's LED will begin flashing, indicating it has entered bind mode.
- Complete Binding: Once the transmitter is in bind mode and the receiver is flashing, the binding process should complete automatically. The transmitter will typically return to its previous menu.
- Verify Connection: If binding is successful, the receiver's LED will stop flashing and remain solid. Test all channels and functions to ensure the model and receiver work as expected.
- Troubleshooting Binding: If binding fails, power off both the transmitter and receiver, then restart the procedure from step 1. Ensure the transmitter and receiver are in close proximity during binding.

Figure 7: Close-up view of the X6B receiver, highlighting the BIND button.
5. Operation
Once bound, the X6B receiver will continuously communicate with your transmitter. The receiver provides various output options to suit your setup:
- PWM Output: For traditional setups where each channel (1-6) connects directly to a servo or ESC.
- PPM Output: A single-wire analog signal carrying all channel data, commonly used with older flight controllers.
- i-BUS Output: A single-wire digital serial protocol that can carry up to 18 channels of data, offering a cleaner wiring solution and often lower latency. This is the preferred method for modern flight controllers.
- Voltage Sensor: Connect a 1S-4S battery balance lead to the voltage sensor port to monitor the main battery voltage directly through your transmitter (if supported by your transmitter).
6. Maintenance
- Keep Dry: Protect the receiver from moisture and humidity, as water damage can lead to malfunction.
- Cleanliness: Periodically inspect the receiver for dust or debris. Use a soft, dry brush or compressed air to clean it.
- Antenna Placement: Ensure the dual antennas are positioned at a 90-degree angle to each other and away from carbon fiber or metal parts of your model to maximize signal reception. Do not cut or modify the antenna wires.
- Connection Integrity: Regularly check all cable connections for looseness or damage. Secure any loose connections to prevent intermittent signal loss.
- Firmware Updates: Check the official Flysky website for any available firmware updates for the X6B receiver. Use the UPDATE button and follow the manufacturer's instructions for safe updating.
7. Troubleshooting
- No Signal/Loss of Control:
- Ensure the receiver is correctly bound to the transmitter.
- Check power supply to the receiver (4.0-8.4V).
- Verify antenna placement and ensure they are not obstructed or damaged.
- Confirm the transmitter is powered on and operating on the correct model memory.
- Binding Failure:
- Ensure both transmitter and receiver are in bind mode simultaneously.
- Keep the transmitter and receiver close during the binding process.
- Refer to your transmitter's manual for specific binding steps.
- Limited Range:
- Check for sources of interference (e.g., other 2.4GHz devices, noisy electronics).
- Ensure antennas are properly oriented and not shielded by carbon fiber or metal.
- Verify the receiver is receiving adequate power.
- Incorrect Channel Output:
- Confirm the correct output mode (PWM, PPM, i-BUS) is selected on your flight controller or configured in your transmitter.
- Check wiring for correct channel assignment.
8. User Tips
- Antenna Orientation: For optimal range and signal reliability, ensure the two receiver antennas are mounted at a 90-degree angle to each other. This helps maintain signal reception regardless of the model's orientation.
- Power Source: Always ensure your receiver is powered within its specified voltage range (4.0-8.4V) to prevent damage and ensure stable operation.
- Range Testing: Before flying, perform a range test in a safe, open area to confirm adequate control range, especially after any changes to your setup.
9. Warranty and Support
For warranty claims, technical support, or service inquiries, please contact the original seller or the manufacturer directly. Keep your proof of purchase for any warranty-related requests. Specific warranty terms and conditions may vary by region and seller.