1. Product Overview
The HNR H9803 Ma E30 Edition is a 1/10 scale remote control flat sports car designed for enthusiasts seeking high-performance driving and drifting. This Ready-To-Run (RTR) model features a detailed simulated bodyshell, advanced brushless power system, and a responsive 2.4G remote control with DVC (gyroscope) function for enhanced stability and control.


2. Safety Information
- WARNING: Not suitable for children under 36 months due to small parts.
- Always operate the RC car in a safe, open area away from people, pets, and obstacles.
- Do not operate near water or in wet conditions.
- Ensure batteries are charged correctly and handled safely.
- Regularly inspect the car for damage and wear before and after each use.
3. Package Contents
The 99% RTR version of the HNR H9803 includes the following components (battery and charger are excluded):
- HNR H9803 RC Car (assembled chassis with electronics, bodyshell)
- 2.4G Remote Control (5-channel with DVC function)
- High-grip racing tires (pre-installed)
- Drifting tires (additional set)
- Instruction Manual
- Small parts and tools (e.g., body clips, wrench)
4. Setup Guide
4.1. Battery Installation (Not Included)
The HNR H9803 requires a 2S~3S Li-po battery. Ensure the battery dimensions do not exceed 145*50*25mm (L*W*H).
- Remove the bodyshell by detaching the body clips.
- Locate the battery compartment on the chassis. The car features a quick-release mechanical principle battery tablet design for easy access.
- Insert the charged Li-po battery into the compartment, ensuring correct polarity.
- Secure the battery using the quick-release mechanism.
- Connect the battery to the ESC (Electronic Speed Controller).

4.2. Remote Control Setup
The remote control operates on a 2.4G frequency and includes a DVC (gyroscope) function for enhanced stability.
- Install appropriate batteries (not included) into the remote control.
- Turn on the remote control, then turn on the RC car. The receiver should automatically bind with the remote. Refer to the remote control's specific manual for binding procedures if necessary.
- Test steering and throttle response to ensure proper function.
4.3. Tire Installation/Change
The car comes with high-grip racing tires pre-installed and an additional set of drifting tires.
- To change tires, use the provided wrench to loosen the wheel nuts.
- Remove the current tires and install the desired set (racing or drifting).
- Ensure the wheel nuts are securely tightened after installation.
- Note the different widths for front and rear wheels for optimal performance.


5. Operating Instructions
5.1. Basic Controls
Use the 5-channel 2.4G remote control to operate the HNR H9803:
- Throttle Trigger: Pull to accelerate forward, push to brake/reverse.
- Steering Wheel: Turn left or right to steer the car.
- Trim Adjustments: Use the trim dials on the remote to fine-tune steering and throttle for straight-line driving.
5.2. DVC (Gyroscope) Function
The integrated DVC (gyroscope) function enhances the car's stability and control, especially during high-speed maneuvers and drifting. This system helps maintain the car's direction and prevents unwanted spins, making it easier to handle.
5.3. Drifting
To experience drifting, install the dedicated drifting tires. Find a smooth, open surface. Practice controlled steering and throttle inputs to initiate and maintain drifts. The DVC function will assist in managing the drift angle.

6. Maintenance
6.1. General Care
- Keep the car clean from dirt, dust, and moisture. Use a soft brush or cloth.
- Store the car and remote control in a dry, cool place when not in use.
- Disconnect batteries from the car and remote when storing.
6.2. Chassis and Drivetrain
- Motor Seat: The motor seat is inlaid with a metal heat sink to support 23T-29T motor teeth, aiding in heat dissipation. Regularly check for debris around the motor.
- Suspension System: The adjustable oil suspension system features shock absorber springs to prevent falling off, mudguard, and a ball head protection cover design. The 3.0MM hard shock absorber axle uses high-density shock absorber oil. Periodically inspect for leaks or damage and ensure smooth operation.
- Gear Transmission: The car features a whole car Peilin bearing configuration, front and rear differential boxes with metal steel teeth, and an oil leakage seal design. It uses a 5.8mm aluminum central drive shaft and #1144 high carbon steel front and rear drive shafts with CVD structure design. Inspect gears and shafts for wear and lubricate as needed.
- Chassis Design: The widened version of the screwless chassis design offers a simple, beautiful appearance, anti-dust effect, and improved stability.




7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Car does not respond to remote. | Low battery in car or remote; remote not bound; power switch off. | Charge/replace batteries; re-bind remote; ensure power switches are ON. |
| Car runs slowly or stops unexpectedly. | Low battery; ESC over-temperature protection activated; motor/drivetrain obstruction. | Charge battery; allow ESC to cool down; check for debris in gears/wheels. |
| Steering is erratic or unresponsive. | Steering servo issue; DVC calibration needed; remote control trim incorrect. | Check servo connections; recalibrate DVC (if applicable); adjust steering trim. |
| Car loses control at high speed. | DVC function not active or improperly configured; loose wheel nuts. | Ensure DVC is enabled and calibrated; check all wheel nuts are tight. |
The ESC (WP-10BL60-RTR) includes protection features such as low-voltage cut-off, over-temperature protection, and throttle out-of-control protection to prevent damage.
8. Specifications
| Feature | Specification |
|---|---|
| Brand Name | MN MODEL |
| Model Number | H9803 |
| Product Name | Werewolf (werewolf) |
| Type | Car (REMOTE CONTROL) |
| Design | Cars |
| Scale | 1:10 |
| Length | 440mm |
| Width | 200mm |
| Height | 150mm |
| Ground Clearance of Chassis | 10~20 mm |
| Material | Metal, Carbon Fiber |
| Remote Control | Yes (2.4G, 5-CH with light control) |
| Controller Mode | MODE1, MODE2 |
| Remote Distance | 100M+ |
| Flight Time | / (Not applicable for car) |
| State of Assembly | Almost Ready (99% RTR, excludes battery and charger) |
| Package Includes | Original Box |
| Power Source | Electric (Battery not included) |
| High-concerned Chemical | None |
| Electric Adjustment (ESC) | Haoying WP-10BL60-RTR/60A |
| Motor | "Haoying" 3652/3300KV Brushless Motor |
| Steering Gear | Digital metal teeth 15 KG |
| Quantity of Differentiator | "Steel" 2P |
| Wheelbase | 260mm |
| Max Battery Size | Less than 145*50*25mm (L*W*H) |
| Wheels (Diameter/Width) | Front: 65/25(F)mm, Rear: 65/30(R)mm |
| Car Speed | 3S/85KM+, 2S/75KM+ |
| Car Shell Thickness | 1.2mm (PC soft shell) |
| Car Shell Color Options | Orange, Red, Black |
| Main Materials of Products | Plastic PA/Hardware/Rubber/Electronics |
| Relevant Certificate | EN71, ROHS, CE |

9. Warranty and Support
This product is offered with several service commitments to ensure customer satisfaction:
- Free Returns: Enjoy free returns within 90 days of purchase.
- Fast Delivery Guarantee:
- $1.00 coupon code if delivery is delayed.
- Full refund if the package is lost.
- Full refund if items are damaged upon arrival.
- Full refund if no delivery within 30 days.
- Security & Privacy: Your personal details are protected and not shared with third parties without consent. Payments are secure.
For any support needs, questions, or warranty claims, please contact the seller, Yolanda's Toy Store, directly through the platform where the product was purchased.