Flysky FS-i4X

Contents

Flysky FS-i4X 2.4G 4ch RC Transmitter Controller with FS-A6 Receiver Instruction Manual

Model: FS-i4X | Brand: Flysky

1. Introduction

The Flysky FS-i4X is a 4-channel 2.4GHz radio control system designed for various remote-controlled models, including fixed-wing aircraft, gliders, and helicopters. This system utilizes AFHDS 2A / AFHDS technology for reliable and interference-free operation. This manual will guide you through the setup, operation, and maintenance of your FS-i4X transmitter and FS-A6 receiver.

What's Included

  • 1 x Flysky FS-i4X 2.4G 4ch RC Transmitter
  • 1 x Flysky FS-A6 Receiver
  • Quick Start Guide (physical or digital)
Flysky FS-i4X Transmitter and FS-A6 Receiver with product packaging
Figure 1: FS-i4X Transmitter and FS-A6 Receiver with product packaging.
Video 1: Product overview of the Flysky FS-i4X Transmitter and FS-A6 Receiver.

2. Safety Information

Always operate your RC equipment responsibly and safely. Failure to do so may result in injury or damage to property. Please read and understand the following safety guidelines:

  • Always ensure your model is in a safe operating condition before use.
  • Operate your RC model in open areas, away from people, animals, and obstacles.
  • Never operate your RC model near power lines, roads, or water.
  • Ensure all batteries are correctly installed and charged according to their specifications.
  • Do not expose the transmitter or receiver to extreme temperatures, moisture, or direct sunlight.
  • Keep the equipment out of reach of children.

3. Product Components

3.1 FS-i4X Transmitter Layout

Labeled diagram of the FS-i4X Transmitter controls including Antenna, Handle, Lanyard Hook, Left/Right Gimbal, Trim 1-4, Bind Button, V-MIX, Reverse Switches, and Power Switch.
Figure 2: FS-i4X Transmitter Control Layout.
  • Antenna: Transmits the radio signal to the receiver.
  • Handle: For carrying the transmitter.
  • Lanyard Hook: Attachment point for a neck strap.
  • Left Gimbal: Controls pitch and roll (or throttle and yaw depending on mode).
  • Right Gimbal: Controls pitch and roll (or throttle and yaw depending on mode).
  • Trim 1-4: Fine-tune adjustments for each channel.
  • Bind Button: Used to pair the transmitter with the receiver.
  • V-MIX: Variable mix switch.
  • Reverse Switches: Used to reverse the direction of servo travel for specific channels.
  • Power Switch: Turns the transmitter on/off.

3.2 FS-A6 Receiver

The FS-A6 is a 6-channel receiver compatible with the FS-i4X transmitter. It features standard servo connections and a bind port.

Close-up of the FS-A6 Receiver with a bind plug inserted.
Figure 3: FS-A6 Receiver with bind plug.

4. Setup Guide

4.1 Battery Installation (Transmitter)

  1. Locate the battery compartment on the back of the FS-i4X transmitter.
  2. Slide the battery cover open.
  3. Insert four (4) AA batteries, ensuring correct polarity (+/-).
  4. Close the battery cover securely.
Rear view of the FS-i4X Transmitter with the battery compartment open, showing where to insert AA batteries.
Figure 4: Transmitter battery compartment.

4.2 Binding the Receiver

Binding is the process of pairing the transmitter with the receiver, allowing them to communicate wirelessly.

  1. Ensure the transmitter is turned OFF.
  2. Connect the bind plug (usually a small jumper) to the 'BIND' port on the FS-A6 receiver.
  3. Connect power to the receiver (e.g., via an ESC or separate battery). The receiver's LED should start flashing rapidly.
  4. While holding down the 'BIND' button on the FS-i4X transmitter, turn the transmitter ON.
  5. The receiver's LED should stop flashing and remain solid, indicating a successful bind.
  6. Release the 'BIND' button on the transmitter, then turn off both the transmitter and receiver.
  7. Remove the bind plug from the receiver.
  8. Turn on the transmitter first, then power on the receiver. The receiver's LED should be solid, confirming the connection.

Note: The FS-A6 receiver includes a small wire antenna. Ensure it is not obstructed for optimal signal reception.

4.3 Mode Selection

The FS-i4X transmitter supports two control modes:

  • Mode 1: Throttle stick on the right.
  • Mode 2: Throttle stick on the left.

Refer to your model's requirements and your personal preference for the appropriate mode. The physical configuration of the gimbals may vary depending on the selected mode.

Flysky FS-i4X Transmitter configured for Mode 1 (Right Hand Throttle).
Figure 5: Transmitter in Mode 1 (Right Hand Throttle).
Flysky FS-i4X Transmitter configured for Mode 2 (Left Hand Throttle).
Figure 6: Transmitter in Mode 2 (Left Hand Throttle).

5. Operation

Once the transmitter and receiver are bound, you can begin operating your RC model. Familiarize yourself with the controls before attempting flight or movement.

5.1 Basic Controls

  • Gimbals: Control the primary movements of your model (e.g., throttle, yaw, pitch, roll).
  • Trims: Use the trim levers to make small adjustments to ensure your model flies straight or remains stable without constant stick input.
  • Switches: The FS-i4X includes various switches (e.g., V-MIX, Reverse Switches) that can be assigned to control different functions on your model, such as landing gear, flaps, or flight modes. Consult your model's manual for specific assignments.

Always perform a range check before operating your model at a distance to ensure proper signal integrity.

6. Maintenance

Proper maintenance will extend the lifespan of your FS-i4X system.

6.1 Cleaning

  • Wipe the transmitter and receiver with a soft, dry cloth.
  • Do not use solvents or abrasive cleaners.
  • Avoid getting moisture into any openings.

6.2 Storage

  • Store the equipment in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Remove batteries from the transmitter if storing for extended periods to prevent leakage.

7. Troubleshooting

No power to transmitter:
Check battery installation and ensure batteries are fresh or fully charged. Verify the power switch is in the ON position.
Receiver not binding:
Ensure the bind plug is correctly inserted into the 'BIND' port. Confirm the transmitter's bind button is held down while powering on. Try repeating the binding process. Check that the receiver is receiving power.
Low Voltage Warning:
The transmitter will issue a low voltage warning if the battery voltage drops below 4.2V. Replace or recharge the transmitter batteries immediately.
Loss of control/short range:
Ensure the receiver's antenna is properly positioned and not damaged or obstructed. Avoid operating near sources of interference (e.g., large metal objects, Wi-Fi routers). Perform a range check to verify signal strength.

8. Specifications

Feature Specification
Channels4
Model TypeFixed-Wing / Glider / Helicopter
RF Range2.4055-2.475GHz
RF Power<20dBm
RF Channel140
Bandwidth500KHz
2.4GHz SystemAFHDS 2A / AFHDS
Modulation TypeGFSK
Stick Resolution1024
Low Voltage Warning<4.2V
DSC PortPS2 PPM
ChargeableNo
Antenna Length (Receiver)26mm
Weight335g
Power6V DC (4 x 1.5V AA batteries)
DisplayLED Indicators
Size174*89*190mm
On-Line UpdateNo
ColorBlack
CertificationsCE0678, FCC
MaterialMetal
Recommended Age14+ years

9. User Tips

  • Included Components: The product package typically includes both the FS-i4X transmitter and the FS-A6 receiver, ready for pairing.
  • Receiver Antenna: The FS-A6 receiver comes with a small wire antenna (26mm length). Ensure this antenna is not cut, damaged, or obstructed and is properly extended for optimal signal reception and control distance. The transmitter itself has an internal or fixed antenna.
  • Control Distance: While specific control distance can vary based on environmental factors, interference, and line of sight, the 2.4GHz AFHDS 2A system is designed for reliable range suitable for hobby RC models. Always perform a range check before flying.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official Flysky website or contact your retailer. Keep your purchase receipt as proof of purchase.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.