MicroZone C7 MINI 2.4G Controller Transmitter and MC8RE Receiver Instruction Manual

1. Introduction

This manual provides detailed instructions for the safe and efficient operation of your MicroZone C7 MINI 2.4G Controller Transmitter and MC8RE Receiver Radio System. This system is designed for controlling various remote-controlled models, including fixed-wing aircraft, multi-axis drones, cars, boats, and even intelligent agricultural machinery. Please read this manual thoroughly before use to ensure proper setup and operation.

2. Safety Information

• Always operate your RC model in open areas, away from people, vehicles, and obstacles.
• Ensure all batteries are fully charged before each use.
• Never operate your RC model near power lines, airports, or restricted airspace.
• Keep the transmitter and receiver away from moisture and extreme temperatures.
• Do not attempt to modify the transmitter or receiver, as this may void your warranty and create safety hazards.
• Always turn on the transmitter first, then the receiver. When finished, turn off the receiver first, then the transmitter.
• This product is recommended for users aged 14 years and older.

3. Package Contents

The package typically includes:

• MicroZone C7 MINI 2.4G Controller Transmitter
• MicroZone MC8RE Receiver (or other selected receiver model)
• Instruction Manual (this document)

Note: Batteries are not included and must be purchased separately.

4. Product Overview

4.1 Transmitter Layout (C7 MINI)

Front Controls:

• Antenna: Built-in 2.4G antenna.
• SW-C, SW-A, SW-B, SW-D: Switches for Channel 5, 6, 7, 8 (auxiliary functions).
• D/R switch: Dual Rate switch.
• Power light: Indicates power status.
• Rocker: Main control sticks (left and right).
• Throttle trim (left-hand throttle): Adjusts throttle neutral point.
• Elevator fine-tuning (right-hand throttle): Adjusts elevator neutral point.
• Rudder fine adjustment: Adjusts rudder neutral point.
• Aileron fine-tuning: Adjusts aileron neutral point.
• Menu key / OK key: Navigates menus and confirms selections.
• Exit button: Exits current menu or function.
• Up button: Navigates up in menus.
• Down button: Navigates down in menus.
• Channel Monitoring: Displays channel output.
• Lock button: Locks controls to prevent misoperation.
• Power Switch: Turns the transmitter on/off.

Back Controls:

• Battery compartment: Houses the power source.
• Audio Interface: For use with computers and analog dongles for simulation training.
• External input DC 6V power supply: For indoor testing or alternative power.

4.2 Receiver Layout (MC8RE-V2)

The MC8RE-V2 receiver features 7 PWM signal outputs, 1 SBUS signal output, and 1 external voltage input. It includes dual external antennas for enhanced signal reception.

Key connections:

• 7 PWM signals: For connecting individual servos or ESCs.
• 1 SBUS signal: For connecting to flight controllers that support SBUS.
• 1 external voltage input: For voltage return functionality. Recommended external input voltage is within 6S.
• External antenna: Dual antennas for improved signal reception.

5. Setup Guide

5.1 Battery Installation (Transmitter)

The C7 MINI transmitter can be powered by 4 AA batteries or a 2S LiPo lithium battery. The battery compartment is located on the back of the transmitter.

To install batteries:

1. Open the battery compartment cover on the back of the transmitter.
2. Insert 4 AA batteries, ensuring correct polarity (+/-).
3. Alternatively, for a 2S LiPo battery, connect it directly to the 2S lithium battery balance port inside the compartment.
4. Close the battery compartment cover securely.

5.2 External Power Supply (Transmitter)

For indoor testing or extended use, the transmitter can be powered via an external DC 6V power supply. The port is located on the side of the transmitter.

5.3 Receiver Binding (Frequency Matching)

To establish communication between the transmitter and receiver, frequency matching (binding) is required:

1. Ensure the receiver is powered on.
2. Press the touch button on the receiver.
3. Turn on the power switch of the remote control (transmitter).
4. The frequency matching should now be successful, indicated by a solid light on the receiver.

6. Operation

6.1 Basic Controls

Refer to Figure 1 for the location of all controls. The main control sticks (rockers) control the primary movements of your model. Trim buttons are used for fine adjustments to ensure stable flight/movement.

6.2 Key Lock

The Key Lock feature prevents accidental input. When activated, the keys become invalid to prevent misoperation.

6.3 Speed Lock (Car/Boat Mode)

In car or boat mode, the Speed Lock function can be engaged. When speed lock is turned on, models with a differential structure will maintain a consistent speed without changes, providing stable control.

6.4 Travel Setting

The Travel Setting allows you to limit the range of movement for the rudder surface, ensuring it operates within your desired parameters.

6.5 Language Switch

The transmitter supports both Chinese and English languages. You can switch between them via the system settings menu.

6.6 Simulation Training

The C7 MINI transmitter can be connected to a computer via its audio interface for simulation training, allowing you to practice controlling your RC model in a virtual environment.

6.7 Runaway Protection

The system includes runaway protection settings. If the receiver loses signal from the transmitter (e.g., transmitter turned off, or model goes out of range), it will return to a pre-set out-of-control protection value to minimize damage to the model.

7. Specifications

7.1 C7 MINI Transmitter Specifications

7.2 MC8RE-V2 Receiver Specifications

8. Maintenance

• Cleaning: Use a soft, dry cloth to clean the transmitter and receiver. Avoid using solvents or abrasive cleaners.
• Storage: Store the system in a cool, dry place, away from direct sunlight and extreme temperatures. Remove batteries if storing for extended periods.
• Battery Care: Always use appropriate chargers for LiPo batteries. Do not overcharge or over-discharge batteries.
• Firmware Updates: Check the manufacturer's website periodically for any available firmware updates for improved performance or new features.

9. Troubleshooting

• No Power: Check battery installation and charge level. Ensure the power switch is fully engaged. If using external power, verify the power supply.
• No Signal/Loss of Control:
  • Ensure the transmitter and receiver are properly bound (frequency matched).
  • Check the distance between the transmitter and receiver; ensure it's within the specified control range.
  • Verify there are no major obstructions or sources of interference (e.g., other 2.4GHz devices) in the operating area.
  • Check receiver and transmitter antenna placement.
• Controls Not Responding Correctly:
  • Check if the Key Lock function is active on the transmitter.
  • Verify servo/ESC connections to the receiver are correct.
  • Recalibrate your model's flight controller or ESCs if necessary.
• Display Issues: Ensure the screen is not exposed to direct sunlight for prolonged periods, although the backlit display is designed for visibility in sunlight.

10. User Tips

• Auxiliary Channels (7 & 8): Channels 7 and 8 are typically used for auxiliary functions on your model. These can include controlling landing gear, flaps, lights, smoke systems, or other additional accessories, depending on your model's capabilities.
• Compatibility: The MicroZone C7 MINI transmitter is designed to work with MicroZone brand receivers, specifically listing models like MC8RE-V2, MC9002, MC6RE-V2, MC7RB-V2, MC3RB, MC4RB, MC6RE, MC7RB, E6R-E, and M-BUS. It is generally not compatible with receivers from other brands such as Spektrum or Orange, as these systems use different proprietary protocols.
• Outdoor Visibility: The backlit display ensures that the operation page can be viewed normally even in direct sunlight, making it suitable for outdoor use.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty claims.