VGR V-640 Professional Barber Combo

Introduction

The VGR V-640 Professional Barber Combo is a versatile grooming kit designed for precise and efficient hair cutting. This combo includes both a cordless hair clipper and a hair trimmer, featuring high-performance motors, durable blades, and convenient charging options. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your VGR V-640 combo.

Important Safety Instructions

To reduce the risk of electric shock, injury, or damage, always follow these basic safety precautions:

• Read all instructions before using the appliance.
• Keep the appliance dry. Do not use it near water or in wet conditions.
• Do not immerse the appliance in water or other liquids.
• Always unplug the appliance from the power outlet immediately after use and before cleaning.
• Keep the appliance out of reach of children.
• Use only the charging cable provided with the appliance.
• Do not operate the appliance if it has a damaged cord or plug, or if it is not working properly.
• Avoid placing the appliance where it can fall into a tub or sink.
• Do not use attachments not recommended by the manufacturer.

Package Contents

Please check the package to ensure all items are present and in good condition:

• 1 x Hair Clipper
• 1 x Hair Trimmer
• 3 x Cutting Guide Combs for Trimmer (1mm, 2mm, 3mm)
• 6 x Cutting Guide Combs for Clipper (1.5mm, 3mm, 4.5mm, 6mm, 9mm, 12mm)
• 1 x USB Charging Cable
• 1 x Cleaning Brush
• 1 x Instruction Manual

Specifications

Setup

1. Initial Charging

Before first use, fully charge both the hair clipper and trimmer. Connect the USB charging cable to the device and a suitable USB power adapter (DC 5V 1A recommended). The LED display will indicate the charging status. The trimmer requires approximately 2.5 hours for a full charge, and the clipper requires 3 hours.

2. Attaching Guide Combs

Select the desired cutting length by choosing the appropriate guide comb. Align the comb with the blade and push it firmly until it clicks into place. To remove, gently pull the comb away from the blade.

• Trimmer Guide Combs: 1mm, 2mm, 3mm
• Clipper Guide Combs: 1.5mm, 3mm, 4.5mm, 6mm, 9mm, 12mm

3. Adjusting the Taper Lever (Clipper Only)

The clipper features an adjustable taper lever on the side, allowing for fine-tuning of cutting lengths between 0.5mm and 2.5mm without changing guide combs. Move the lever up for a shorter cut and down for a longer cut.

Operating Instructions

1. Power On/Off

Locate the ON/OFF switch on the device. Slide the switch to the 'ON' position to power on the clipper/trimmer. Slide it to the 'OFF' position to turn it off.

2. Using the Clipper/Trimmer

• Hair Clipper: Ideal for general haircuts and fading. Attach the desired guide comb and adjust the taper lever for precise length control. Move the clipper against the direction of hair growth for an even cut.
• Hair Trimmer: Perfect for detailing, outlining, and trimming beards or mustaches. Use without a guide comb for a close trim (less than 0.5mm) or with the smaller guide combs for specific lengths.

The devices feature a dual-speed motor with up to 9000 RPM for efficient cutting. They can be used for both wet and dry haircuts.

3. Video Demonstration

For a visual guide on operating the VGR V-640 Professional Barber Combo, please watch the official product demonstration video below.

Maintenance

1. Cleaning the Blades

After each use, turn off and unplug the device. Use the provided cleaning brush to remove any loose hairs from the blades. The blades are designed for washing under water; however, ensure the main body of the device does not get wet if it's not explicitly rated as waterproof. Dry the blades thoroughly after washing.

2. Lubrication

Regular lubrication helps maintain blade performance and longevity. Apply a small drop of clipper oil (not included due to airline regulations) to the blades after cleaning, especially if washing them with water. Run the device for a few seconds to distribute the oil evenly.

3. Storage

Store the clipper and trimmer in a cool, dry place, away from direct sunlight and moisture. Ensure the devices are clean and fully charged before storing for extended periods.

Troubleshooting

• Device not turning on: Ensure the battery is charged. Connect to the USB charging cable and allow sufficient time to charge.
• Poor cutting performance: Clean the blades thoroughly to remove any hair buildup. Ensure the blades are properly lubricated. If performance does not improve, the blades may be dull and require replacement (contact support for options).
• Excessive noise or vibration: This can sometimes be caused by hair trapped in the blade mechanism or insufficient lubrication. Clean and oil the blades. If the issue persists, discontinue use and contact support.

User Tips

• Always ensure the blades are clean and oiled before each use for optimal performance and to prevent pulling hair.
• When using guide combs, start with a longer comb length than you think you need, and gradually reduce it to achieve your desired style.
• For a smoother cut, stretch the skin taut while moving the clipper/trimmer against the direction of hair growth.
• The LED display is useful for monitoring battery life, so keep an eye on it to avoid interruptions during grooming sessions.

Warranty and Support

All VGR products come with a 12-month warranty from the date of purchase. This warranty covers manufacturing defects and ensures the product is free from defects in material and workmanship under normal use.

If the item is damaged during shipping or if you encounter any issues with your product, please contact the seller or VGR customer support directly. Provide details of the issue and any relevant purchase information. They will review your situation and provide appropriate assistance or a solution.