LYZRC L900 PRO

Contents

LYZRC L900 PRO Drone Spare Parts Instruction Manual

Model: L900 PRO

Introduction

This manual provides detailed instructions for identifying, installing, and maintaining spare parts for your LYZRC L900 PRO GPS Foldable RC Quadcopter. It covers motor arms, propellers, and associated components. Please read this manual carefully before attempting any repairs or replacements to ensure safe and correct operation.

Safety Information

  • Always disconnect the drone's battery before performing any maintenance or part replacement.
  • Use only original or manufacturer-approved spare parts to ensure compatibility and performance.
  • Handle small components and tools with care to avoid injury.
  • Keep all parts and tools out of reach of children.
  • Ensure all screws are tightened securely after installation, but do not overtighten.

Package Contents

Depending on your purchase, your package may contain one or more of the following components:

  • Motor Arms (Front A, Front B, Rear A, Rear B)
  • Propellers (Blades)
  • Mounting Screws
LYZRC L900 PRO Drone Front Rear Arm Set with Propellers and Screws
Example of a LYZRC L900 PRO Drone Front Rear Arm Set with Propellers and Screws.

Part Identification

The LYZRC L900 PRO drone uses specific motor arms for each position. It is crucial to identify the correct arm before replacement.

  • Front A Arm: Typically located at the front-left or front-right position, identified by its specific shape and wiring.
  • Front B Arm: Typically located at the front-left or front-right position, identified by its specific shape and wiring.
  • Rear A Arm: Typically located at the rear-left or rear-right position, identified by its specific shape and wiring.
  • Rear B Arm: Typically located at the rear-left or rear-right position, identified by its specific shape and wiring.

Refer to the images below for visual identification of individual arm types:

LYZRC L900 PRO Drone Front A Arm
Front A Arm
LYZRC L900 PRO Drone Front B Arm
Front B Arm
LYZRC L900 PRO Drone Rear A Arm
Rear A Arm
LYZRC L900 PRO Drone Rear B Arm
Rear B Arm

Setup and Installation

Replacing Motor Arms

  1. Power Off: Ensure your LYZRC L900 PRO drone is powered off and the battery is removed.
  2. Identify Damaged Arm: Determine which motor arm needs replacement (Front A, Front B, Rear A, or Rear B).
  3. Remove Screws: Carefully unscrew the mounting screws that secure the damaged arm to the drone's body. There may be screws on the top and bottom of the drone chassis.
  4. Disconnect Wiring: Gently disconnect the motor's wiring harness from the drone's main circuit board. Note the orientation and connection point for reassembly.
  5. Remove Damaged Arm: Once screws are removed and wiring is disconnected, carefully detach the damaged arm.
  6. Install New Arm: Take the new, correct replacement arm. Connect its wiring harness to the corresponding port on the drone's circuit board. Ensure the connection is firm and correctly oriented.
  7. Secure Arm: Position the new arm in place and secure it with the mounting screws. Do not overtighten.
  8. Test: Reinsert the battery and perform a brief test flight (if applicable) to ensure the new arm functions correctly and the drone flies stably.

Replacing Propellers

  1. Power Off: Ensure your drone is powered off and the battery is removed.
  2. Identify Damaged Propeller: Locate the propeller(s) that need replacement.
  3. Remove Propeller: Gently twist and pull the damaged propeller upwards from the motor shaft. Some models may require a small screwdriver to loosen a screw on the propeller hub.
  4. Install New Propeller: Take a new propeller. Note that propellers are often marked (e.g., A or B, or with a dot) to indicate their rotation direction and must be installed on the correct motor. Push the new propeller firmly onto the motor shaft until it clicks into place or secure it with the screw if applicable.
  5. Verify: Ensure all propellers are securely attached and rotate freely without obstruction.

Maintenance

  • Regular Inspection: Periodically inspect motor arms and propellers for cracks, bends, or other damage.
  • Cleanliness: Keep motor arms and propellers free from dirt, dust, and debris. Use a soft, dry cloth for cleaning.
  • Storage: Store spare parts in a cool, dry place away from direct sunlight and extreme temperatures.

Troubleshooting

  • Drone unstable after arm replacement: Double-check that the correct arm (Front A, Front B, Rear A, Rear B) was installed in the correct position. Ensure all wiring connections are secure and screws are tightened.
  • Motor not spinning: Verify the motor's wiring harness is fully connected. Check for any visible damage to the motor or wiring. If the motor is still not spinning, it may be faulty and require replacement.
  • Excessive vibration: Ensure propellers are correctly installed and balanced. Replace any bent or chipped propellers. Check that motor arms are securely fastened and not loose.

Specifications

FeatureSpecification
MaterialComposite Material
RC Parts & AccsPropellers, Motor Arms
For Vehicle TypeRC Quadcopters (Drones)
Is ElectricNo Battery (refers to the parts themselves)
Is Batteries IncludedNo
Recommend Age (for drone use)3-6Y, 6-12Y, 14+y
OriginMainland China

User Tips

  • Verify Part Selection: Before purchasing, carefully check the product description and images to ensure you are ordering the correct motor arm (Front A, Front B, Rear A, or Rear B) for your specific drone's needs. The product is often sold as individual arms, not a set of four, unless explicitly stated.
  • Propeller Orientation: Always ensure propellers are installed with the correct orientation (clockwise or counter-clockwise rotation) as indicated by markings on the propeller or in the drone's main manual. Incorrect installation can lead to unstable flight or inability to take off.
  • Keep Spare Screws: Small screws can be easily lost during replacement. Keep a small container or magnetic mat to hold them.

Warranty and Support

For warranty information, technical support, or further assistance with your LYZRC L900 PRO drone spare parts, please contact the seller directly through the platform where you made your purchase. Provide your order number and a clear description of the issue for prompt service.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.