FlySky FS-R4D-ESC

Contents

FlySky FS-R4D-ESC 2-in-1 Receiver and ESC Instruction Manual

Model: FS-R4D-ESC

1. Introduction

The FlySky FS-R4D-ESC is an advanced 2-in-1 bidirectional receiver integrated with an Electronic Speed Control (ESC) and LED light set control. Designed for various RC vehicle models, it offers compact design, reliable two-way transmission, and comprehensive protection features. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure optimal performance of your FS-R4D-ESC unit.

2. Key Features

The FS-R4D-ESC receiver boasts the following features:

  • Compact design for easy integration into various RC models.
  • External single antenna for enhanced signal reception.
  • Output of PWM signals for precise control and dedicated car light control signals.
  • Two-way transmission for real-time feedback.
  • Automatic binding process for quick and easy setup.
  • ESC parameters configurable directly from the transmitter.
  • Integrated battery voltage protection and over-voltage protection.
  • Overheating protection to prevent damage under heavy load.
  • Locked rotor protection for motor safety.
  • Adaptation to a wide variety of vehicle models, including 1/10 crawlers, on-road cars, off-road short course trucks, and trucks.
FlySky FS-R4D-ESC receiver with key features listed
Figure 1: FS-R4D-ESC receiver highlighting its key features.

3. Specifications

Refer to the table below for detailed technical specifications of the FS-R4D-ESC receiver:

Parameter Value
Product ModelFS-R4D-ESC
Compatible TransmittersFS-HW G4P, FS-MG4, FS-G7P or FS-MG7, etc.
Model Type1/10 crawler, on-road car, off-road short course truck, and truck
Number of Channels4
Number of Light Interfaces6
RF2.4GHz ISM
2.4G ProtocolANT
AntennaSingle External Antenna
Input PowerLiPo (2-3S) / NiMH (5-9Cell)
BEC Output6V/3A
Continuous/Peak Current40A/200A
Motor TypeBrushed Motor
Applicable Motors550, 540, 390, 370 or 280 Brushed Motor
Data OutputPWM
Resolution4096
Temperature Range-10°C to +60°C
Humidity Limit20%-95%
Distance≥150m (Ground Distance without interference)
WaterproofPPX7
Online UpdateNone
Dimensions44*30*16.7mm
Weight43g (Without pin header)
CertificationCE, FCC ID: 2A2UNR4DESC
FlySky FS-R4D-ESC receiver with detailed specifications
Figure 2: Detailed specifications of the FS-R4D-ESC receiver.

4. Product Overview and Interfaces

Familiarize yourself with the various components and connection interfaces of the FS-R4D-ESC receiver using the diagram below:

Diagram of FlySky FS-R4D-ESC receiver with numbered interfaces and components
Figure 3: FS-R4D-ESC receiver interface diagram.
  1. CH1 Channel Interface
  2. CH3 Channel Interface
  3. CH4 Channel Interface
  4. Left Headlight Interface
  5. Right Headlight Interface
  6. Front Headlight Interface
  7. Rear Taillight Interface
  8. Ambient Light Interface
  9. Roof Light Interface
  10. Car Light Interface "-" pole
  11. Car Light Interface "+" pole
  12. Power Switch Tab
  13. Power Switch Wire
  14. Motor Wire "+"
  15. Power Input "+"
  16. Power Input "-"
  17. Motor Wire "-"
  18. Heat Sink
  19. Antenna
  20. Receiver Indicator Light
  21. ESC Indicator Light
  22. Channel Interface Signal
  23. Channel Interface "+"
  24. Channel Interface "-"

5. Setup Instructions

5.1. Initial Connection

  1. Connect the motor wires (14 and 17) to your brushed motor, ensuring correct polarity (+ to + and - to -).
  2. Connect the power input wires (15 and 16) to your LiPo (2-3S) or NiMH (5-9Cell) battery.
  3. Connect your steering servo to the CH1 Channel Interface (1).
  4. If using additional accessories, connect them to the appropriate channel interfaces (e.g., CH3, CH4) and light interfaces (4-11).
  5. Ensure the antenna (19) is positioned correctly for optimal signal reception, away from metal parts.

5.2. Binding Process (Automatic Binding)

The FS-R4D-ESC supports automatic binding. Follow these general steps:

  1. Ensure your compatible FlySky transmitter (e.g., G7P/MG7) is powered off.
  2. Power on the FS-R4D-ESC receiver. The Receiver Indicator Light (20) should start flashing, indicating it's in binding mode.
  3. Turn on your transmitter. The transmitter should automatically detect and bind with the receiver.
  4. Once successfully bound, the Receiver Indicator Light (20) on the FS-R4D-ESC will become solid.
  5. Test all controls (steering, throttle, lights) to ensure proper functionality.

Note: Refer to your specific FlySky transmitter's manual for detailed binding procedures, as steps may vary slightly.

6. Operating Instructions

6.1. Power On/Off

  • To power on, connect the battery and ensure the power switch (if used via Power Switch Tab 12 and Wire 13) is in the 'ON' position.
  • To power off, disconnect the battery or switch the power switch to 'OFF'.

6.2. ESC and Light Control

  • The integrated ESC controls the speed and direction of your brushed motor via the throttle channel on your transmitter.
  • The LED light set control allows you to manage connected lights (headlights, taillights, ambient lights, roof lights) through your transmitter's auxiliary channels, if configured.
  • ESC parameters can be configured directly from your compatible FlySky transmitter. Consult your transmitter's manual for specific menu navigation and adjustment options.

6.3. Protection Features

The FS-R4D-ESC includes several protection mechanisms:

  • Battery Voltage Protection: Automatically reduces power or cuts off the motor if the battery voltage drops below a safe level, preventing over-discharge.
  • Over-voltage Protection: Protects the unit from damage due to excessively high input voltage.
  • Overheating Protection: Reduces power or shuts down the ESC if its temperature exceeds safe operating limits.
  • Locked Rotor Protection: Detects if the motor is stalled and prevents damage to the motor and ESC.

7. Maintenance

  • Cleaning: Regularly clean the receiver and ESC unit to remove dust, dirt, and debris. Use a soft brush or compressed air. Avoid using solvents or harsh chemicals.
  • Inspection: Periodically check all wires and connectors for signs of wear, damage, or loose connections. Ensure the antenna is intact and properly routed.
  • Storage: When not in use, store the unit in a dry, cool place, away from direct sunlight and extreme temperatures. Disconnect the battery before storage.
  • Waterproof Rating: The unit has a PPX7 waterproof rating, meaning it can withstand immersion in water up to 1 meter for 30 minutes. However, it is recommended to avoid prolonged exposure to water and ensure all connections are dry before operation.

8. Troubleshooting

Problem Possible Cause Solution
Receiver not powering on Incorrect battery connection; dead battery; faulty power switch. Check battery polarity and connection; charge or replace battery; inspect power switch.
No response from controls after power on Not bound to transmitter; transmitter off; incorrect channel connections. Perform binding procedure; ensure transmitter is on and charged; verify servo/motor connections to correct channels.
Motor not running or running intermittently Loose motor wires; motor locked rotor; ESC overheating; low battery voltage. Check motor connections; clear any obstructions to the motor; allow ESC to cool; charge battery.
Lights not working Incorrect light connection; faulty LED; transmitter not configured for light control. Verify light connections to correct interfaces; test LEDs; configure transmitter auxiliary channels for light control.
Short control range Antenna obstructed or damaged; interference; low transmitter battery. Ensure antenna is clear and undamaged; avoid operating near strong interference sources; replace transmitter batteries.

9. User Tips

  • Cable Management: Keep all wiring neat and secure to prevent interference and accidental disconnections. Use cable ties or heat shrink tubing where appropriate.
  • Antenna Placement: For best range and signal quality, ensure the receiver antenna is extended and positioned as far as possible from other electronics and metal components in your vehicle.
  • ESC Calibration: If experiencing inconsistent throttle response, perform an ESC calibration with your transmitter. Refer to your transmitter's manual for the specific procedure.
  • Battery Monitoring: Always monitor your battery voltage, especially with LiPo batteries, to avoid over-discharge which can permanently damage the battery. The built-in voltage protection helps, but external monitoring is always a good practice.
  • Environmental Considerations: While the unit is waterproof (PPX7), extreme temperatures or prolonged exposure to moisture can still affect performance and longevity. Operate within the specified temperature and humidity limits.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the official FlySky support channels. Keep your proof of purchase for any warranty claims. Do not attempt to repair the unit yourself, as this may void the warranty.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.