QCY HT10 AilyBuds Pro+

Contents

QCY HT10 AilyBuds Pro+ ANC Wireless Earphones User Manual

QCY HT10 AilyBuds Pro+ Earbuds and Charging Case

Experience superior audio with adaptive noise cancellation and advanced features.

1. Product Overview

1.1 Package Contents

  • QCY HT10 AilyBuds Pro+ Earbuds
  • Charging Case
  • Type-C Charging Cable
  • User Manual
Package Contents: Earbuds, Case, Cable, Manual

Image: Package Contents

1.2 Earbud Components

  • Sound Hole: Audio output.
  • LED Indicator: Shows status.
  • Touch Panel: For controls.
  • Pogo Pins: For charging.
  • Microphones: 6-mic array for calls and noise cancellation.

2. Setup Instructions

2.1 Initial Pairing

  1. Take out both earbuds, peel off the isolation film from each, and place them back into the charging case. Close the lid to activate the new device.
  2. Retrieve both earbuds again.
  3. Refresh your phone's Bluetooth devices list, select "QCY AilyBuds Pro+" and complete the pairing.

Note: Opening the charging case turns on the earbuds. If not, try again after charging.

2.2 Multi-Device Connection

The QCY HT10 AilyBuds Pro+ supports connecting to two devices simultaneously. This feature needs to be enabled in the QCY APP settings.

  1. Power on the earbuds to initiate pairing. After connecting to Device A, turn off Bluetooth on Device A. The earbuds will enter pairing mode again.
  2. Enable Bluetooth on Device B and select "QCY AilyBuds Pro+" for pairing.
  3. On Device A, turn on Bluetooth and click the paired earbuds' name. Successful pairing means the earbuds are now connected to both devices simultaneously.

Note: The multi-point connection function and LDAC audio decoding format cannot be enabled simultaneously.

Multipoint Connection & Bluetooth 5.3 setup

Image: Multipoint Connection Setup

2.3 Factory Reset (Clearing Pairing Records)

Use this method if you encounter connection issues.

  1. Place the earbuds in the charging case, open the lid.
  2. Press and hold the charging case button for 10 seconds. The earbuds will flash red 5 times.
  3. The reset is complete after the blinking stops.

After the factory reset, follow the initial pairing method to connect for normal usage.

3. Operating Instructions

3.1 Wearing the Earbuds

  1. Properly wear the earbuds on both the left and right sides. After wearing them, you can make slight adjustments by rotating to find a personally comfortable and secure position.
  2. Ensure the microphone opening is facing downward towards the mouth.

Incorrect earbuds placement may affect both calls and hearing to varying degrees. If the fit is not snug enough, the ANC noise cancellation effectiveness may decrease. Try adjusting the wearing angle and direction before reactivating the adaptive noise cancellation mode.

3.2 Touch Controls

Easy Touch Control diagram

Image: Touch Control Functions

  • Power On: Open the charging case (earbuds inside) or, if the earbuds are outside the case, long-press the touch panel for 1.5 seconds.
  • Power Off: Place the earbuds into the charging case and close the lid.
  • Answer/End Call: Double-tap the touch panel.
  • Reject Call: Long-press the touch panel for 1.5 seconds.
  • Play/Pause: Double-tap the touch panel.
  • Next Track: Triple-tap the right ear touch panel.
  • Voice Assistant: Triple-tap the left ear touch panel.
  • Low Latency Mode: Long-press the left ear touch panel (80ms ultra-low latency game mode).
  • ANC Mode: Long-press the right ear touch panel to cycle between Adaptive ANC On/Off.

3.3 QCY APP Customization

Download the QCY App to personalize your earbuds. The app allows you to:

  • Customize EQ sound effects.
  • Switch modes.
  • Reset earbuds.
  • Upgrade firmware.
  • Disable touch controls.
  • Check earbud fit.
QCY APP Customizable Control interface

Image: QCY APP Interface

Note: The QCY App requires Android 8.0 or above, or iOS 13 or above. Pairing pop-up requires Android system and cannot be enabled until you open the app and enable Bluetooth on your phone.

4. Maintenance

4.1 Charging the Earbuds

  • Place the earbuds into the charging case.
  • While charging, the red light on the earbuds stays on.
  • The light turns off when fully charged.

4.2 Charging the Case

  • Connect the Type-C charging cable to the charging port on the case.
  • While charging, the red light on the case stays on.
  • The white light stays on when fully charged.

4.3 Battery Status Indicators

  • Sufficient Battery: When the charging case is opened, the white light will stay on for 5 seconds before turning off.
  • Low Battery: When the charging case is opened, the red light will stay on for 5 seconds before turning off.
  • Insufficient Battery: When the charging case has insufficient battery, the red light will quickly flash three times before turning off.
28-Hour Long Battery Life diagram showing ANC ON/OFF battery life

Image: Battery Life Overview

5. Troubleshooting (FAQ)

  • Q: Only one earbud has sound.
    A: Put both earbuds back into the charging case and close the cover, then take them out again. If the issue persists, perform a factory reset on both earbuds.
  • Q: Phone prompts

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.