Flysky FS-GR3E

Contents

Flysky FS-GR3E 3 Channel 2.4G Waterproof Receiver User Manual

For RC Car, Truck, and Boat Applications

1. Introduction

The Flysky FS-GR3E is a 3-channel 2.4GHz receiver designed for use with RC cars, trucks, and boats. It features a waterproof design and a built-in failsafe function to enhance the safety and reliability of your remote-controlled models. This manual provides essential information for setting up, operating, and maintaining your FS-GR3E receiver.

Flysky FS-GR3E 3-Channel 2.4G Waterproof Receiver
Figure 1: Flysky FS-GR3E 3-Channel 2.4G Waterproof Receiver

2. Specifications

FeatureSpecification
Number of Channels3
Data Collection InterfaceNone
Suitable ModelsCar / Boat
Antenna Length26MM (without copper tube)
Frequency Range2.4055-2.475GHz
Body Weight5G
Band Width500KHz
Input Power Supply4.0-6.5V
Number of Bands140
Dimensions (L*W*H)35mm * 22mm * 12mm
2.4G ModeFirst generation of automatic frequency hopping digital system
Joystick Resolution4096
Modulation MethodGFSK
Appearance ColorTransparent gray
Receive Sensitivity-105dbm
CertificationCE 0678, FCC
Compatible TransmittersFS-GT2, FS-GT3B, FS-GT3C, FS-GT2E, FS-CT6B and others
Flysky FS-GR3E receiver with dimensions labeled
Figure 2: FS-GR3E Receiver Dimensions (35mm x 22mm x 12mm)

3. Setup

3.1 Component Identification

Close-up of Flysky FS-GR3E receiver showing channel ports
Figure 3: FS-GR3E Receiver Port Layout (CH1, CH2, BIND/CH3, VCC)

The FS-GR3E receiver features the following ports:

  • CH1: Channel 1 output (e.g., Steering servo)
  • CH2: Channel 2 output (e.g., Throttle ESC)
  • BIND/CH3: Used for binding the receiver to the transmitter and also serves as Channel 3 output.
  • VCC: Power input (4.0-6.5V)
  • Signal LED: Indicates receiver status.
  • Failsafe Key: Button for setting failsafe.

3.2 Binding Procedure

To establish communication between your FS-GR3E receiver and a compatible Flysky transmitter, follow these steps:

  1. Ensure your transmitter is turned OFF.
  2. Connect a bind plug (included with some kits, or a standard servo plug with a jumper wire) to the BIND/CH3 port on the receiver.
  3. Connect the power supply (4.0-6.5V) to the VCC port on the receiver. The Signal LED on the receiver should start flashing rapidly, indicating it is in binding mode.
  4. Turn ON your transmitter while holding down its bind button (refer to your transmitter's manual for its specific bind button location).
  5. The Signal LED on the receiver should stop flashing and remain solid, indicating a successful bind.
  6. Release the bind button on the transmitter, then turn OFF both the transmitter and receiver.
  7. Remove the bind plug from the receiver.
  8. Turn ON the transmitter first, then power ON the receiver. The receiver's Signal LED should be solid, confirming a successful connection.
Flysky FS-GR3E receiver with bind plug inserted
Figure 4: Bind plug inserted into BIND/CH3 port for binding

3.3 Connecting Servos/ESC

Connect your servos and Electronic Speed Controller (ESC) to the corresponding channels on the receiver:

  • CH1: Typically for steering servo.
  • CH2: Typically for ESC (throttle control).
  • CH3: For auxiliary functions if your transmitter supports it, or can be used for a third servo.

Ensure correct polarity when connecting components. The signal pin is usually on the top or outer edge, positive (+) in the middle, and negative (-) on the bottom or inner edge.

3.4 Failsafe Setup

The failsafe function ensures that your model returns to a predetermined safe state (e.g., throttle to neutral, steering straight) if the signal from the transmitter is lost. To set the failsafe:

  1. Ensure the receiver is bound to the transmitter and both are powered ON.
  2. Set your transmitter controls to the desired failsafe positions (e.g., throttle to neutral, steering centered).
  3. Press and hold the Failsafe Key button on the receiver for approximately 2-3 seconds until the Signal LED flashes rapidly, then release.
  4. The failsafe settings are now stored. Test the failsafe by turning off your transmitter while the receiver is powered on. The model's controls should move to the set failsafe positions.

4. Operating

Once the receiver is bound and components are connected, operating your model is straightforward:

  1. Always turn on your transmitter first.
  2. Then, power on your model (receiver). The receiver's Signal LED should be solid, indicating a stable connection.
  3. Operate your model using the transmitter controls.
  4. When finished, turn off your model (receiver) first, then turn off the transmitter.

5. Maintenance

5.1 Waterproofing

The FS-GR3E receiver is designed to be waterproof. While this provides protection against splashes and light moisture, it is not intended for prolonged submersion. Always ensure all connections are secure and dry before operation, especially in wet conditions. After exposure to water, allow the receiver to dry completely before storing.

5.2 General Care

  • Keep the receiver clean and free from dirt, dust, and debris.
  • Avoid exposing the receiver to extreme temperatures or direct sunlight for extended periods.
  • Handle the antenna carefully to prevent damage. Ensure the antenna is positioned correctly for optimal signal reception.
  • Store the receiver in a dry, cool place when not in use.

6. Troubleshooting

6.1 No Signal / Loss of Control

  • Check Binding: Ensure the receiver is correctly bound to your transmitter. Re-perform the binding procedure if necessary.
  • Power Supply: Verify that the receiver is receiving adequate power (4.0-6.5V) and that the battery is charged.
  • Antenna Placement: Ensure the receiver antenna is not obstructed by carbon fiber or metal parts and is positioned for optimal reception. Avoid coiling the antenna tightly.
  • Range: Operate your model within the effective range of your transmitter.
  • Interference: Avoid operating near strong sources of 2.4GHz interference (e.g., Wi-Fi routers, other RC systems).

6.2 Failsafe Not Activating

  • Re-set Failsafe: Ensure the failsafe positions are correctly set and stored by following the failsafe setup procedure.
  • Binding Status: Failsafe relies on a stable bind. Verify the receiver is properly bound.

7. User Tips

  • Antenna Orientation: For best signal reception, try to position the antenna in a way that it is perpendicular to the transmitter antenna, and away from large metal objects in your model.
  • Power Source: Always use a stable power source within the specified voltage range (4.0-6.5V) to prevent damage and ensure reliable operation.
  • Pre-Flight Checks: Before each use, perform a range check and verify that all controls respond correctly and that the failsafe function is working as expected.
  • Water Protection: While waterproof, consider adding an extra layer of protection (e.g., conformal coating or a waterproof box) if your model will be frequently exposed to harsh wet environments.

8. Warranty and Support

For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase. Information regarding specific warranty periods and support procedures will be provided by your point of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.