1. Introduction
This manual provides detailed instructions for the Flysky FS-ST8 2.4G 10CH ANT RGB Assistant 3.0 Radio Transmitter and the accompanying FS-SR8 Receiver. This system utilizes the 2.4GHz ANT (Ant Protocol) automatic frequency hopping digital system, offering 8-12 channels and various binding modes for stable communication over long distances. It is compatible with a wide range of RC models, including fixed-wing aircraft, delta-wing airplanes, helicopters, gliders, multicopters, cars, engineering vehicles, robots, and boats.
Please read this manual carefully to ensure personal safety and proper operation of your equipment. If you encounter any problems, refer to this manual first. If the issue persists, contact customer service via www.flysky-cn.com.
Product Video Overview
This video provides a visual overview of the Flysky FS-ST8 transmitter and its features.
2. Safety Information
Pay close attention to the following symbols and their meanings. Failure to follow these warnings could cause damage, injury, or death.
- Danger: Not following these instructions may lead to serious injuries or death.
- Warning: Not following these instructions may lead to major injuries.
- Attention: Not following these instructions may lead to minor injuries.
2.1 Safety Guide
- Do not use the product at night or in bad weather (rain, thunderstorm, limited visibility). This can cause erratic operation or loss of control.
- Do not use the product when visibility is limited.
- Do not use the product on rainy or snowy days. Any exposure to moisture can cause erratic operation or loss of control.
- Avoid interference: Do not operate near any site where other radio control activity may occur, near power lines or communication broadcasting antennas, near people or roads, or on any body of water when passenger boats are present.
- Do not use this product when you are tired, uncomfortable, or under the influence of alcohol or drugs.
- The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a large object can block the RF signal and lead to loss of control.
- Do not touch any part of the model that may generate heat during operation, or immediately after use. The engine, motor or speed control, may be very hot and can cause serious burns.
- Ensure the product is properly installed in your model.
- Disconnect the receiver battery before turning off the transmitter to prevent unintended operation and accidents.
- Ensure that all servos operate in the correct direction. If not, adjust the direction first.
- Make sure the model stays within the system's maximum range to prevent loss of control.
3. Setup and Installation
3.1 Installing Transmitter Battery
The FS-ST8 transmitter supports AA batteries or 2S lithium batteries (JST interface). Always use specified batteries.
- Open the battery compartment cover on the back of the transmitter.
- Insert 4 AA batteries with sufficient electricity, ensuring correct polarity and contact with metal terminals. Alternatively, connect a 2S 7.4V lithium battery to the JST interface.
- Close the battery compartment cover, being careful not to pinch the battery wiring.
Image: Rear view of the FS-ST8 transmitter showing the open battery compartment for AA batteries.
Image: Rear view of the FS-ST8 transmitter showing the open battery compartment with a 2S Lipo battery connected via JST.
3.2 Installing Receiver and Servo (FS-SR8)
Install the FS-SR8 receiver and servos according to the following diagram and instructions. Ensure all interfaces are 2.54 mm standard pins and follow the direction indicated on the receiver.
Image: Diagram illustrating the connection of servos to the FS-SR8 receiver's channels (CH1-CH8) and auxiliary ports.
Receiver Interfaces:
| Pin No. | Function |
|---|---|
| CH1/PPM | Channel 1 / PPM output |
| CH2 | Channel 2 |
| CH3 | Channel 3 |
| CH4 | Channel 4 |
| CH5 | Channel 5 |
| CH6 | Channel 6 |
| CH7 | Channel 7 |
| CH8 | Channel 8 |
| BIND interface | Binding port |
| BVD/VCC | Battery voltage detection / Power supply interface |
| SENS interface | Sensor interface |
| SERVO/S.BUS interface | Servo / S.BUS output |
| - (Power cathode) | Negative power terminal |
| + (Power anode) | Positive power terminal |
| Antenna | Antenna connection point |
| BIND button | Button for binding process |
Antenna Placement: The FS-SR8 receiver has two external antennas. To ensure optimal signal quality, keep antennas vertical to the ground and extend them out of the model, perpendicular to the ground. Avoid pulling or tying antennas with servo cables, and keep them away from metal materials.
Image: Top view of the FS-SR8 receiver showing its two external antennas.
Image: Side view of the FS-SR8 receiver, highlighting the antenna orientation.
4. Operation Guide
4.1 Power-On
- Check that the transmitter battery is fully charged and installed.
- Press and hold the power button on the transmitter until the screen lights up.
- Power on the receiver.
Warning: For your safety, ensure the transmitter switches and throttle are in the safe position before powering on. If switches are not in the highest position or throttle is not at the lowest, a prompt will appear. Adjust them accordingly.
4.2 LED Status (Transmitter)
The multi-color LED indicator on the transmitter displays various states:
- Off: Transmitter is not powered on.
- Solid Red: Transmitter is powered on and working normally.
- Flashing: Indicates various states like binding mode, low battery, or firmware update.
The LED color and brightness can be adjusted via TX SET > SYSTEM SETTINGS > LED in the function menu.
4.3 Binding (Transmitter and Receiver)
The transmitter and receiver are pre-bound from the factory. If you need to bind with other receivers, follow these steps:
The FS-ST8 transmitter supports both 2-Way and 1-Way binding, with 2-Way binding as the default. Before binding, set the RF System, RF Standard, Output Mode, and Frequency according to your application.
Binding Steps:
- On the transmitter, scroll the Scroll Wheel to navigate to "START" in the BIND SETTINGS menu and press the Scroll Wheel to enter bind mode.
- Press and hold the BIND button on the receiver while powering it on. The receiver's LED should flash, indicating bind mode.
- Once binding is complete, the receiver's LED will stop flashing and remain solid.
- Verify that the transmitter and receiver are working correctly. If issues arise, repeat the binding process.
Note: Different receivers may have different bind procedures. Refer to the Flysky website for specific receiver manuals.
4.4 Stick Calibration
Calibration is necessary if there's data offset due to physical wear. The transmitter is factory-calibrated, but you can recalibrate if needed:
- Power on the transmitter, enter the
TX SETmenu, and selectCALIBRATION. Follow prompts to pressSTART. - Move the sticks to their maximum and minimum travel range in each direction, then release them.
- Tap
CALIBRATIONto exit the interface.
Note: If calibration fails, it means the control did not reach maximum/minimum travel. Recalibration is required.
4.5 Power-Off
- Disconnect the receiver power.
- Press and hold the transmitter power button for a moment to turn it off.
Danger: Always disconnect receiver power before turning off the transmitter to prevent damage or serious injury.
5. Main Interface Overview
The main interface displays critical information and provides quick access to menus.
Image: The main display screen of the FS-ST8 transmitter, showing signal strength, voltages, model name, and timer.
Key Elements:
- Status Bar: Shows signal strength and TX voltage. When the receiver is bound, and the voltage of the receiver is 4.9V, then R4.9V will be displayed here.
- Icons: Indicate enabled functions (e.g., Lock, Flight mode, Throttle hold, GPS).
- SENSORS: Displays information from up to three sensors.
- T1/T2 Trim, T3/T4 Trim: Trim settings.
- Model Name and Number: Current model identification.
- Timer: Displays active timer.
Quick Access:
- Select the SENSOR area and press Scroll Wheel to quickly access the SENSOR menu.
- Select the TIMER area and press Scroll Wheel to quickly access the TIMERS menu.
- Select the C1 area and press Scroll Wheel to quickly access the SELECT TYPE menu.
- Select the MODEL01 area and press Scroll Wheel to quickly access the model menu.
6. Function Menu and Settings
The FS-ST8 transmitter organizes functions into four main categories: TX SET (Transmitter Settings), RX SET (Receiver Settings), MDL SET (Model Menu), and GENER MENU (General Menu).
To access the function menu, press the MENU button from the main interface. Use the Scroll Wheel to navigate and select options.
Image: Diagram showing the hierarchical structure of the FS-ST8's function menu, categorized into TX SET, MDL SET, GENER MENU, and RX SET.
6.1 TX SET - Transmitter Settings
This menu contains settings related to the transmitter itself.
6.1.1 MODEL
Manages model data, allowing up to 10 sets of model data to be saved and recalled.
- MODEL SELECT: Choose from saved model data.
- MODEL NAME: Edit the name of the selected model (up to 8 characters).
- MODEL COMB.: Combine multiple models and assign a switch for quick switching.
- SELECT TYPE: Choose from 9 different model types (e.g., Fixed-wing, Helicopter).
- MODEL COPY: Copy existing model settings for quick setup of similar models.
- MODEL RESET: Reset all model parameters to factory settings.
- RACE MODE: Quickly disable LOW SIGNAL ALARM and TELEMETRY ALARM for racing.
6.1.2 TRAINER
Designed for beginners, allowing an instructor (trainer) to supervise a student. It features TRAINER mode and STUDENT mode, and a switch can be set to enable or disable the trainer function.
- Connect two transmitters via a trainer cable.
- Set instructor's transmitter to TRAINER mode and student's to STUDENT mode.
- A switch enables/disables trainer control.
6.1.3 THROTTLE ALARM
Monitors throttle position and emits an alarm if the throttle stick crosses a set value.
- Set
THROTTLE ALARMto ON/OFF. - Adjust
TRIGGER VALUE(e.g., 0%).
6.1.4 STICK MODE
Allows selection of four stick modes (Mode 1, 2, 3, 4) to suit user habits. CH1 (Aileron), CH2 (Elevator), CH3 (Throttle), CH4 (Rudder).
Image: Diagrams illustrating the four different stick modes (Mode 1, 2, 3, 4) and their corresponding channel assignments for Aileron, Elevator, Throttle, and Rudder.
Note: Changing between modes 2/4 and 1/3 will necessitate changing the throttle gimbals position. Refer to section 7.3 for details on swapping gimbals.
6.1.5 SYSTEM SETTING
Configures various transmitter system parameters:
- SOUND/VOLUME: Adjust system and alarm sounds.
- ALARM TIME: Set idle alarm time.
- VIBRATION/GRADE: Set system and alarm vibration intensity.
- BATTERY TYPE: Select battery type (AA or Lipo).
- LED COLOR/BRIGHTNESS: Customize LED indicator color and brightness.
- CONTRAST: Adjust LCD screen contrast.
- BACKLIGHT TIME: Set backlight duration.
- AUTO SHUTDOWN: Configure auto-shutdown time.
6.1.6 TIMERS
Provides two independent timers for count-up or countdown, useful for races or monitoring battery usage.
- Set timer type (UP/DOWN) and duration.
- Assign START, STOP, and RESET switches.
- Set throttle trigger value to start the timer.
- Configure alarm for reminder 10 seconds prior to expiration.
6.1.7 SWITCH SETTINGS
Used to set which controls can be assigned, including SW class switches, Dials (Upgraded version), buttons on the back (Upgraded version) or Knobs. Through this function, you can set the throttle mode for self-centering or non-self-centering by setting THRO. If you set to self-centering, the stick position is not prompted upon power-on. You can also set the number of channels of transmitter by setting CH NUM, and the range is 8 to 12.
6.1.8 BOOT SETTINGS
Enables/disables the switch self-check prompt function and failsafe setting prompt function in case of power-on.
6.1.9 FIRMWARE UPDATE
Used to update the firmware of the transmitter. When the firmware needs to be upgraded, it is necessary to put the transmitter into upgraded mode using this function first.
- Download the latest firmware from the Flysky website.
- Connect the transmitter and the PC via a USB Type-C cable. Open the firmware on a computer.
- At the transmitter side, select
FIRMWARE UPDATE. The system will show a prompt menu, selectOKand press Scroll Wheel to put the transmitter into updating mode. ClickUpdateon the firmware screen on the computer.
Warning: Always ensure sufficient power supply for the transmitter when using this function. To avoid the receiver losing control, make sure to power off the receiver before starting this function. Do not disconnect the USB Type-C cable during the firmware updating, otherwise the transmitter may occur a fault.
6.1.10 ABOUT
Used to display the system information, such as hardware version, etc.
6.1.11 HELP CENTER
To obtain the user manual via this function.
6.1.12 FACTORY RESET
Used to restore the entire transmitter system to the factory settings in case a number of parameters are adjusted incorrectly during operation. Reset all data of the model current in use. All other models are reset except MDL SET, MODEL TYPE and MODEL NAME.
6.2 MDL SET - Model Settings
This menu configures functions specific to the model type.
6.2.1 CONDITION
For some advanced users, there may be several different requirements when flying the same model. This function allows setting up to three flight conditions with different priorities, assignable to a switch.
6.2.2 RATE/CURVE
This function can be divided into two parameters. Firstly, the rate can be quickly adjusted in different states to set the output value of certain channels. Secondly, the curve is set according to different flight effect requirements. It adjusts channel output rates (0-100%) and curves for precise control, especially for 3D maneuvers.
6.2.3 THROTTLE CURVE
This function is specifically for the throttle channel to achieve the perfect match between throttle output and motor or engine. It can be set individually in different flight conditions, with 7 dynamic adjustment points throughout the travel.
6.2.4 THROTTLE HOLD
This is a common function used for adjustment and trimming. It is also used before take-off and during landing to maintain the normal output of other channels while completely locking the throttle channel output. This ensures a safe working state.
6.2.5 DUAL-RATE/DR
To set the DUAL-RATE/DR function, switch, and effective condition. The transmitter supports 4 sets of DUAL-RATE/DR settings. When 2 or more sets of DUAL-RATE/DR settings are assigned to the same channel and all are enabled, the one that is placed later has a higher priority.
6.2.6 V-TAIL
This function is designed for specific aircraft models, such as fixed-wing aircraft with V-tails. It allows you to perform mixing control for both channels in the same direction or in the reverse direction.
6.2.7 DELTA-WING MIX
This function is designed for specific aircraft models, such as delta-wing aircraft with two ailerons. Use this function to make the ailerons perform as elevators.
6.2.8 TRACK MIX
This function is designed for specific models, such as tank and excavator models. The two tracks can be driven in the same direction or in reverse directions. CH1 for reverse motion/differential steering, CH2 for forward/backward movement.
6.2.9 PITCH CURVE
This function is set for some specific models, for example, helicopter models. Adjust the helicopter's pitch motion curve to match the throttle output to achieve the best flight status of the helicopter.
6.2.10 GYROSCOPE1 & 6.2.11 GYROSCOPE2
To set the value of the gyroscope and whether to enable the function. Output channels for Gyroscope1 and Gyroscope2 must be different.
6.3 GENER MENU - General Settings
This menu contains general functions.
6.3.1 MONITOR
To display the real time output status of all channels. Includes a hidden "Channel test" function (hold Scroll Wheel) to check channel normality.
Danger: To avoid accidents, do not activate channel test function when the transmitter is connected with the models or the engines of the model is started.
6.3.2 REVERSE
You can perform the reverse processing of the output data of one channel or more channels. This function is used in the debugging of a model.
6.3.3 END POINTS (Including SUBTRIM)
Adjusts the travel amount of the servo output. This function is used in debug. This function can be used to set the travel of the HIGH, LOW and SUBTRIM at both ends of the channel respectively.
6.3.4 CH SPEED
This function can be used to adjust the output speed of some channels for a specific model. For example, in the landing gear retraction, users may want it to be opened slowly, therefore, you can slow down the output speed of the corresponding channel.
6.3.5 AUX CH
For some models with complex functions, we provide up to 12 channels of output, 8 of which are auxiliary channels for the most effective control of multiple functions in different ways. The AUX CH (auxiliary channel) function is used to set the control settings for CH5 to CH12, assigning the controls to the channels for operation.
6.3.6 TRIMS
To set the step value of the trims.
6.3.7 MIXES
MIXES is enabled for some models that require two channels to act in linkage. For example, you can perform rudder compensation so that the aircraft will not lift its nose when throttling up. This transmitter provides up to 8 groups of mixes.
6.4 RX SET - Receiver Settings With INT RF
The RX SET (receiver setting) menu provides a number of function setting menus to allow you to set up the receiver system in all aspects. This menu configures the receiver system when using the internal RF module.
6.4.1 BIND SETTINGS
Refer to section 4.3 for binding details.
6.4.2 FAILSAFE
Failsafe is an important safety setting. It can be used to protect the model from loss or reduce the degree of loss when the receiver loses signal without control. In addition, it plays a role in protecting personnel safety. You can set the data in case of out-of-control for all output channels.
- Failsafe Judgment Time: Configurable within a range of 250ms to 1000ms (default 700ms for gliders, helicopters, delta wings, fixed-wing aircraft, and multicopters; 300ms for engineering vehicles, boat models, car models, and robots).
- i-BUS/PPM/PWM Signal: Options include NOT SET (no output), NONE (no output for i-BUS/PPM/PWM), or ON (output set values).
- Set All Channels: Set all channels to NONE, HOLD (last value), or FIXED VALUE.
- CH1-CH18: Set individual channels to None, Hold, or Fixed value.
Caution: Remove propellers prior to the failsafe test.
6.4.3 SENSOR
As an interesting feature for two-way communication systems, sensors can be used to send back some information you need through the receiver. The transmitter can support up to 15 different types of returned data to provide you with the feedback of seven basic parameters, i.e., TX VOL (TX voltage), RX VOL (RX voltage), BVD VOL (BVD voltage), SIGNAL (signal intensity), NOISE, SNR (noise rate) and RSSI.
- BVD Function: Monitors external battery voltage (0-70V) with alarm settings.
- Supports up to 15 i-BUS series sensors (e.g., altitude, speed, voltage, temperature, GPS).
- Configure sensors to display on the main menu and set alarm functions.
6.4.4 SENSOR CALIBRATION
This function is a special feature provided by FLYSKY. The setting allows you to make corrections to the parameters of some external sensors that need to be calibrated, so as to display the sensing data accurately (e.g., BVD voltage sensor).
6.4.5 GPS SETTING
This function needs to be used with the FS-CGPS01 GPS sensor of FLYSKY. You can view the information returned by GPS sensor after calibrating the GPS and setting an appropriate time. You can reset the start point when the displayed distance is inaccurate.
6.4.6 i-BUS SETTINGS
This function is a unique and powerful serial communication protocol system provided by FLYSKY. It can be output to any channel by setting. For receivers with i-BUS interface and corresponding accessories, such as Serial Bus Receiver FS-CEV04.
6.4.7 RANGE TEST
Used to test whether wireless communication between the transmitter and the receiver is normal and the ambient radio interference. The theoretical remote control distance can be reduced to 30-40 meters for close-range testing.
- Make sure the transmitter and the receiver are bound normally.
- Access the
RANGE TESTinterface and pull down the SWD button. - One person stands in place with the model in hand, and the other person holds the transmitter and gradually moves away to 30-40 meters and walks around with this distance as a radius centered on this model.
- Make sure that the transmitter antenna is not blocked. The receiver antenna is placed at 90 degrees if there are two antennas, and there is no interference between the transmitter and the receiver in the open area.
- Observe the signal strength of the transmitter. If the signal strength is high and stable, it means that the radio frequency of this system works normally.
6.4.8 RF SETTINGS
This is an extended function option. The setting is used when the external RF module is needed. The EXT RF can be set to one of the following items: OFF, PPM.P, PPM.N, S.BUS, FRM303, CRSF and CRSF2, so as to be compatible with the external RF module with different protocol. When the external RF is set to CRSF2 or FRM303, the INT RF (local RF) is disabled.
6.4.9 LOW SIGNAL ALARM
This function is used to set up the alarm feature for signal strength when the transmitter and receiver communicate in two-way mode.
- Set
STATUSto ON/OFF. - Adjust
RANGE(signal strength value) andREPEATinterval. - Enable/disable sound and vibration.
6.4.10 TELEMETRY ALARM
This function is used to set up the alarm function for telemetry loss when the transmitter and receiver communicate in two-way mode.
- Set
STATUSto ON/OFF. - Adjust
ALARM VALUE(trigger time). - Enable/disable sound and vibration.
6.5 RX SET - Receiver Settings With EXT RF (FRM303 RF MODULE)
When EXT RF is set to FRM303 module, the settings for the receiving system includes BIND SETTINGS, PORT PROTOCOL, FAILSAFE, PWM FREQUENCY, SIGNAL STRENGTH, GPS SETTINGS, SENSOR, GPS SETTING, RF SETTINGS and ABOUT RECEIVER.
6.5.1 BIND SETTINGS
After the FRM303 RF module is connected to the FS-ST8 transmitter, it can be bound with the FlySky 3rd generation receiver (classic edition and enhanced edition).
- Classic Edition: CLASSIC 18CH or C-FAST 10CH.
- Enhanced Edition: ROUTINE 18CH, FAST 8CH, or LORA 12CH.
- Set RF Standard to 1WAY or 2WAY.
6.5.2 PORT PROTOCOL
Set the type of output signal of the receiver interface. The interface shown on the left side can be set, and on the right side, the protocols that can be set.
6.5.3 FAILSAFE
For failsafe, the transmitter provides the following three settings: To disable the signal output of i-BUS-out and PPM protocol interfaces in case of out-of-control, i.e., no output for i-BUS-out & PPM interfaces in case of out-of-control. Set all channels. That is, all channels are set to the same value. It can be set one of NONE, HOLD, or FIXED VALUE. Set failsafe values channel by channel to one of NONE, FIXED VALUE or HOLD.
6.5.4 PWM FREQUENCY
The receiver's output frequency of PWM signals can be regulated. Theoretically, the higher the frequency, the faster the signal is refreshed, and the faster the servo responds to the signal change. However, some servos may not support PWM signals with excessively high frequency. You may need to take into account the servo's performance when doing such settings.
6.5.5 SIGNAL STRENGTH
Through this function, you can select a channel to output the signal strength value of the receiver. After the function is enabled, the selected channel does not perform the output of transmitter's corresponding channel function, but outputs the receiver's signal strength value. This function is necessary for users who use FPV glasses in the operations of traversers. CH14 is the default.
6.5.6 SENSOR
Except the functions described in 6.4.3 RX SET-SENSOR section, it can also check the temperature and voltage information of external RF module FRM303, and set whether to display it on the home page and alarm function as well.
6.5.7 GPS SETTING
Refer to section 6.4.5 for details.
6.5.8 RF SETTINGS
Except the functions described in 6.4.8 RX SET-RF SETTING section, it can also enable or disable the buzzer alarm function, and you can set an appropriate power if the FRM303 RF module support power regulation by POWER SETTING function. In addition, you can view the related information about the RF module as well.
6.5.9 ABOUT RECEIVER
Displays information about the bound receiver (model, version, ID).
7. DIY Customization and Maintenance
The FS-ST8 system allows for various reconfigurations and customizations.
7.1 Throttle Metal Bracket Installation
The FS-ST8 transmitter has two sticks in the factory settings, and one is the self-centering stick. To use the non self-centering stick, please follow the steps below to replace the self-centering stick to the non self-centering stick. The throttle plate includes two types: setback sense throttle plate and non setback sense throttle plate (the installation steps are the same).
- Use a screwdriver to remove the 5 marked screws on the back cover.
- Carefully pull the front and back covers apart, ensuring no damage to cables.
- Loosen assembly screws and remove the gimbal.
- Loosen assembly screws and remove the plate assembly.
- Remove the spring hook assembly.
- Place the new throttle plate (setback sense or non-setback sense) into position and secure it with screws.
- Place the plate assembly back and secure with 4 screws.
- Carefully insert the back cover wiring plug into the motherboard, re-close the transmitter, and tighten screws.
Danger: This operation is only for the self-centering stick. It is forbidden to disassemble the non-self-centering stick. Be careful to avoid damaging cables or terminal blocks during disassembly and reassembly.
Image: Exploded view of the FS-ST8 transmitter showing screw locations for disassembly and gimbal removal.
7.2 Throttle Spring Installation
The following instructions explain how to change the non self-centering to self-centering.
- Disassemble the transmitter and remove the gimbal and throttle plate (refer to 7.1).
- Place the spring hook assembly into position and hook the spring onto the hook located inside the transmitter.
- Insert the two dowels as shown in the manual.
- Place the plate assembly back and secure with 4 screws.
Image: Step-by-step diagram for installing the throttle spring to enable self-centering.
7.3 Swapping Gimbals
When changing between modes 2/4 (M2/M4) and modes 1/3 (M1/M3), you will need to switch the gimbals around so that the throttle gimbal is on the correct side.
- Disassemble the transmitter by removing the 8 screws on the back cover.
- Swap the gimbals and rotate them 180 degrees, aligning with screw holes. Secure with screws. (There is no need to disconnect the cables).
- Reassemble the transmitter.
- Power on and verify functionality via
Main menu > GENER MENU > MONITOR.
Image: Diagram showing the process of swapping gimbals within the transmitter.
7.4 Device Holder Installation
Mobile devices, such as mobile phone, can be used in real time to receive information from an aircraft, it may be fitted into the mobile device bracket for your convenience.
- Insert the holder into the reserved hole on the transmitter.
- Tighten the locking knob on the back of the holder.
- To fix a mobile phone: Loosen the locking knob, place the phone in the middle of the holder, slide the holder back down, and tighten the locking screw.
Image: Step-by-step diagram for installing the device holder onto the transmitter and securing a mobile phone.
7.5 Stealth I/O RF Module Adapter Installation
If you have purchased the RF module adapter, fix it on the transmitter by following the steps below:
- Place the left and right RF module adapters as shown, aligning screw holes.
- Tighten the four screws to secure the adapters.
Note: The transmitter Stealth I/O RF module interface is designed without power supply. If connecting an external RF module via the adapter, it needs separate power.
Image: Diagram showing the installation of the Stealth I/O RF module adapter and its pin definitions (PPM/TX, RX, NC, GND, S.port).
7.6 Antenna Assembly Installation
If you have purchased 2.4G antenna assembly inner-screw-inner-hole, the installation procedure is described below.
- Remove the back cover of the transmitter.
- Remove the small adhesive piece from the antenna hole plug using tweezers.
- Insert the outer-screw-inner-pin end of the IPEX to SMA adapter cable into the corresponding position and snap the hexagonal nut.
- Snap the IPEX connector end of the adapter cable onto the motherboard antenna holder.
- Insert plum washers and spring spacers, then screw in the hexagonal nut and tighten the antenna post.
- Close the back cover, ensuring wire terminals are in good contact and not pressed.
Image: Step-by-step diagram for installing the 2.4G antenna assembly, including removal of the antenna hole plug and connection of the adapter cable.
8. Troubleshooting
- Erratic Operation/Loss of Control: Check for interference (other radio activity, power lines), ensure line of sight, and avoid bad weather. Verify proper antenna placement on both transmitter and receiver.
- Binding Issues: Ensure correct binding procedure (Section 4.3) is followed. Check RF System, RF Standard, Output Mode, and Frequency settings. Refer to Flysky website for specific receiver bind procedures.
- Control Data Offset: Perform Stick Calibration (Section 4.4) if physical wear causes data offset.
- Transmitter Not Powering On: Check battery installation and charge level.
- Firmware Update Failure: Ensure sufficient power supply during update and do not disconnect USB cable.
- Model Responds Incorrectly: Use the REVERSE function (Section 6.3.2) to adjust servo directions.
- Low Signal Alarm: Check antenna placement and perform a Range Test (Section 6.4.7). Adjust LOW SIGNAL ALARM settings (Section 6.4.9).
- Telemetry Loss Alarm: Check for signal interference and adjust TELEMETRY ALARM settings (Section 6.4.10).
- Physical Damage (e.g., broken toggle switch, half-black display screen): This indicates potential impact or manufacturing defect. Contact customer service for repair or replacement.
9. Product Specifications
9.1 FS-ST8 Transmitter Specifications
| Feature | Specification |
|---|---|
| Product Model | FS-ST8 |
| Number of Channels | 8-12 |
| Compatible Receiver | FS-SR8 (Adapts receiver with ANT protocol) |
| Compatible RC Models | Fixed-wing aircraft, helicopters, gliders, delta-wing airplanes, multicopters, racing drones, engineering vehicles, robots, cars or boats, etc. |
| RF | 2.4GHz ISM |
| Maximum Power | < 20dBm (e.i.r.p.) (EU) |
| RF Protocol | ANT |
| Distance | More than 1000m (Air distance without interference) |
| Resolution | 4096 |
| Input Power | 1.5AA*4/2S Lipo (JST) |
| Charging Jack | None |
| Data Connector | USB Type-C, 3.5mm audio jack |
| Low Voltage Warning | AA battery: <4.2V/ Lipo battery: <7.2V |
| Antenna | Built-in double antennas |
| Display | 128*64 LCD (Black and white dot matrix screen) |
| Temperature Range | -10°C ~ +60°C |
| Humidity Range | 20% ~ 95% |
| Firmware Update | Supported |
| Color | Black |
| Dimensions | 176*210.9*82.5mm (6.93*8.3*3.25 inches) |
| Weight | 420g (0.93lbs) |
| Certifications | CE, FCC ID: N4ZST800 |
9.2 FS-SR8 Receiver Specifications
| Feature | Specification |
|---|---|
| Product Model | FS-SR8 |
| Compatible Transmitters | FS-ST8 (Adapts transmitter with ANT protocol) |
| Compatible RC Models | Fixed-wing aircraft, helicopters, gliders, delta-wing airplanes, multicopters, racing drones, engineering vehicles, robots, cars or boats, etc. |
| Number of PWM Channels | 8 |
| RF | 2.4GHz ISM |
| RF Protocol | ANT |
| Resolution | 4096 |
| Distance | More than 1000m (Air distance without interference) |
| Antenna | Two antennas |
| Operating Voltage | 3.5~9V/DC |
| Data Output | PWM/PPM/i-BUS/S.BUS |
| Firmware Update | Supported |
| Temperature Range | -10°C ~ +60°C |
| Humidity Range | 20% ~ 95% |
| Weight | 10g |
| Dimensions | 44.8*26.6*11.3mm |
| Certifications | CE, FCC ID: 2A2UNSR800 |
10. Package Contents
The package contents may vary between Standard and Upgraded Editions. Please consult your dealer for specific details.
10.1 Standard Edition
| Number | Name | Quantity |
|---|---|---|
| 1 | FS-ST8 Transmitter | 1 |
| 2 | FS-SR8 Receiver | 1 |
| 3 | Quick Start Guide | 1 |
Image: Contents of the Standard Edition package, including the FS-ST8 transmitter, FS-SR8 receiver, and quick start guide.
10.2 Upgraded Edition
| Number | Name | Quantity | Remark |
|---|---|---|---|
| 1 | FS-ST8 Transmitter | 1 | |
| 2 | FS-SR8 Receiver | 1 | |
| 3 | Quick Start Guide | 1 | |
| 4 | Throttle Self-centering Modification Parts | 1 | |
| 5 | FGPZ05 RF Module Adapter | 1 | |
| 6 | Throttle Bracket Parts | 1 | |
| 7 | Device Holder | 1 | Optional |
| 8 | External FS-FRA01 2.4G Antenna Modification Parts | 1 | Optional |
| 9 | FGPZ03 RF Module Adapter | 1 | Optional |
| 10 | FGPZ05 RF Module Adapter | 1 | Optional |
Image: Contents of the Upgraded Edition package, including the FS-ST8 transmitter, FS-SR8 receiver, quick start guide, and various optional modification parts.
11. User Tips
- Handle with Care: The transmitter, especially the display screen and toggle switches, can be sensitive to impact. Avoid dropping or rough handling to prevent physical damage.
- Screen Protection: Consider adding a screen protector to the display to prevent scratches or damage that could lead to a "half-black screen" issue.
- Pre-Flight Check: Always perform a thorough pre-flight check, including battery levels, servo directions, and signal range, to ensure safe operation.
- Firmware Updates: Regularly check the Flysky website for firmware updates to ensure optimal performance and access to new features.
12. Warranty and Support
For any issues or problems not resolved by this manual, please contact your local dealer or Flysky customer service via their official website: www.flysky-cn.com.
Product information and firmware updates are regularly posted on the Flysky website.
User Manual (PDF): A detailed user manual in PDF format is available for download. View User Manual (PDF)
13. Certifications
13.1 DoC Declaration
ShenZhen FLYSKY Technology Co., Ltd. declares that the Radio Equipment [FS-ST8] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at: www.flyskytech.com/info_detail/10.html.
13.2 CE Warning
The CE mark warns that the installation of the antenna used in this transmitter must be kept at a distance from all personnel and should not be used with any other transmitter. The end user and installer must follow antenna installation instructions and transmitter operating conditions to meet RF exposure compliance requirements.
13.3 FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. It generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Measures to correct interference:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a different circuit from the receiver.
- Consult the dealer or an experienced radio/TV technician.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
SAR: The maximum SAR value is 2.57W/kg when the equipment is used 5mm close to the user.
14. Environmentally Friendly Disposal
Old electrical appliances must not be disposed of with residual waste. They should be disposed of separately at communal collecting points. The owner is responsible for bringing old appliances to these points for recycling valuable raw materials and treating toxic substances.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to instructions. Improper disposal of batteries (e.g., into fire, hot oven, mechanical crushing, high temperature, low air pressure) can result in explosion or leakage of flammable liquid/gas.