MN MODEL MN89K

Contents

MN89K RC Receiver Instruction Manual

Model: MN89K | Brand: MN MODEL

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your MN89K RC receiver. The MN89K receiver is designed for use with various MN MODEL RC vehicles, including the MN86S, MN128, and MN99S, offering reliable remote control functionality and integrated light control capabilities.

2. Safety Information

⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

  • Always operate your RC vehicle in a safe environment, away from people, pets, and obstacles.
  • Ensure all connections are secure before operation.
  • Do not expose the receiver to water or extreme temperatures.
  • Keep out of reach of small children. Recommended age: 14+ years.

3. Package Contents

The package typically includes:

  • 1 x MN89K RC Receiver
  • (Other components may vary based on specific product bundles)

4. Specifications

FeatureSpecification
Model NumberMN89K
Brand NameMN MODEL
MaterialPlastic
For Vehicle TypeCars
Remote Control Peripherals/DevicesRECEIVERS
RC Parts & AccsRECEIVERS
UseVehicles & Remote Control Toys
Quantity1 pcs
Is ElectricNo Battery
Is it battery/power supplyN
Is it charger/adapterN
Is Batteries IncludedNo
Recommend Age14+y
OriginMainland China
CertificationCE
Package Length13 cm
Package Width8 cm
Package Height5 cm
Package Weight0.05 kg

5. Setup

5.1 Receiver Overview

Familiarize yourself with the receiver's ports and buttons:

MN89K RC Receiver Diagram showing Bind button, Light Port, Channels 1-6, and Antenna

Image: MN89K RC Receiver with labels for Bind button, Light Port, Channels 1-6, and Antenna.

5.2 Battery Installation (for Transmitter)

The receiver itself does not require batteries, but the remote control transmitter does. Open the battery compartment cover on your remote control, install three AA or 1S lithium batteries, and then close the cover.

5.3 Receiver Installation

Install the receiver securely within your RC vehicle's chassis. Ensure all wiring is neatly routed and not interfering with moving parts.

RC receiver being connected inside a vehicle chassis

Image: Visual guide for connecting the receiver inside an RC vehicle chassis.

5.4 Binding the Receiver to the Transmitter

For first-time use, you need to bind the receiver to your remote control transmitter:

  1. Turn on the remote control transmitter.
  2. Power on the receiver (connect it to the vehicle's power source).
  3. Press the BIND button on the receiver.
  4. The binding process should complete, and the receiver will be paired with the transmitter.

6. Operating Instructions

6.1 Basic Operation

After successful binding, the remote control functions can be used normally to control your RC vehicle.

6.2 Remote Control Layout

Familiarize yourself with the controls on your remote control transmitter:

Remote control transmitter diagram with labels for ST Trim, ST Rate, ST Rev, TH Rev, TH Trim, TH Rate, Turn Signal Light, ON/OFF, CH4, CH5, CH6, Left/Right (CH1), Forward/Backward (CH2), Light SW (CH3), Battery Capacity

Image: Diagram of the remote control transmitter showing various trim, rate, reverse, and channel controls, along with the light switch and battery compartment.

6.3 Light Control Modes

The receiver supports two light control modes, switchable by tapping the BIND button:

  • Mode 1: Use CH3 to control car lights. A short tap activates the headlight, and a long press activates emergency flashers.
  • Mode 2: CH3 switches to normal mode, providing a standard channel output without specific light functions.

6.4 Channel Recommendations

The following table provides recommended connections for each channel:

ChannelFunction
CH1Servo
CH2Throttle
CH3Lights/Horn Controller
CH4Gear shift
CH5Diff Lock
CH6Winch

7. Maintenance

  • Keep the receiver clean and free from dust and debris.
  • Regularly check all wiring for signs of wear or damage.
  • Store the receiver in a dry, cool place when not in use.
  • Avoid strong impacts or dropping the receiver.

8. Troubleshooting

Q: The receiver is not responding to the transmitter.
A: Ensure the receiver and transmitter are properly bound. Repeat the binding process as described in Section 5.4. Check that both the transmitter and receiver have adequate power.
Q: Lights are not working or behaving unexpectedly.
A: Verify that the light control mode is correctly set (Mode 1 or Mode 2) by tapping the BIND button. Check all light connections to CH3.
Q: Can this receiver connect to a standard MN controller or an MN99S stock transmitter?
A: Yes, the MN89K receiver is designed to be compatible with standard MN controllers, including the MN99S stock transmitter, after the binding process is successfully completed.

9. User Tips

  • When upgrading from an older receiver model (e.g., MN88K), ensure you follow the binding procedure carefully for the new MN89K receiver.
  • Experiment with the two light control modes to find the one that best suits your driving style and lighting needs.
  • Always perform a range check before operating your RC vehicle at a distance, especially after changing batteries or components.

10. Warranty and Support

For warranty information and technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.