QIACHIP KR2201GS

Contents

QIACHIP 433MHz Wireless Switch User Manual

Model: KR2201GS | Brand: QIACHIP

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your QIACHIP 433MHz Wireless Switch (Model KR2201GS). This device is designed to provide convenient wireless control for various home appliances, including lighting, electric doors, and other switch-controlled devices. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety Warnings

  • This device is for indoor use only.
  • This device should not be exposed to dripping water or any other dangerous sources.
  • This device should only be installed by adults.
  • Do not install near any heat sources.
  • Do not use this device with dimmers.
  • Do not use this device in a fully enclosed fixture.
  • Pay attention to electricity and do not use it in humid places.
  • If the unit is heavier than the replacement unit, it may reduce the stability of some fixtures and affect the contacts.

3. Specifications

FeatureDetail
ModelKR2201GS
Working VoltageAC 90V~250V
Quiescent Current<5MA
Max Current10A
Max Load2200W
RF Frequency433-433.92MHz
Working Temperature-30°C ~ +80°C
Receiving Sensitivity>108 dbm
Storage Remote ControlsUp to 25 pieces
Support Encoding1527 Learning code, 2262 fixed code
RF Operating ModeASK superheterodyne wireless reception
Receiving RangeOpen space: >50 meters, Indoor partition wall: 15 meters
Wall Switch Size86 standard size
Switch Battery TypeAAA batteries
Channel2
Wireless CommunicationRF, Wire Control
UseAir Conditioner, Universal, Lighting, Electric Door, Switch

4. Package Contents

The package typically includes:

  • QIACHIP KR2201GS Mini Relay Receiver
  • Wireless Wall Panel Switch (quantity may vary based on order)
  • Remote Control (quantity may vary based on order)
  • User Manual (this document)
QIACHIP KR2201GS receiver and wall panel switch
Example of package contents: 1 receiver and 1 wall panel switch.

5. Setup and Installation

Ensure power is disconnected before performing any wiring. Installation should only be performed by qualified adults.

5.1 General Wiring Diagram (Wired between Power and Lights)

This diagram illustrates the basic connection of the QIACHIP Smart Switch receiver between the power source and the light fixture. The compact receiver is designed to easily fit into standard wiring boxes such as rose/canopy, junction box, or switch box.

General wiring diagram for QIACHIP Smart Switch
General wiring diagram showing input, output, and switch connections.

Wiring Details:

  • Input (AC 90-250V): Connect the Live (L) wire to the red input wire and the Neutral (N) wire to the white input wire of the receiver.
  • Output (to Light): Connect the Live (L) wire of the light to the blue output wire and the Neutral (N) wire of the light to the black output wire of the receiver.
  • Switch: The green wire connects to the external switch.

For a visual guide on wiring, please refer to the official product video:

Video demonstrating the wiring process for the QIACHIP Smart Switch.

5.2 Wiring for KR2201G (Remote Control Only)

This model is controlled exclusively by a remote control and does not support an external wired switch.

Wiring diagram for KR2201G remote control only
Wiring for KR2201G, controlled only by remote.

5.3 Wiring for KR2201GS (Remote Control Wiring Method)

This diagram shows the wiring for the KR2201GS when controlled by a remote control, with provisions for an external switch connection.

Wiring diagram for KR2201GS with remote control
Wiring for KR2201GS, controlled by remote with external switch option.

5.4 Wiring for KR2201GS (Simultaneous Use of Remote Control and External Switch)

The KR2201GS allows for dual control, connecting to both the original switch and a 433MHz wireless remote control. This setup requires no rewiring of existing switches.

Wiring diagram for KR2201GS with simultaneous remote and external switch control
Wiring for KR2201GS with both remote and external switch control.
Diagram showing two-way control with the QIACHIP Smart Switch
Illustration of two-way control capability.
Wide application scenarios for the QIACHIP Smart Switch
Examples of wide application scenarios including adding a wall switch, replacing hard-to-reach switches, multi-way switches, and dual control.

5.5 Product Dimensions

The compact design of the QIACHIP receiver allows for easy integration into various electrical boxes.

Dimensions of the QIACHIP receiver
Receiver dimensions (40mm x 40mm x 21mm).

6. Operating Instructions

6.1 Wireless Remote Control Function

The receiver unit has a pairing button, often referred to as the "Smart Circuit Breaker Pairing Button", which is used for learning remote control codes.

Location of the Smart Circuit Breaker Pairing Button
Location of the pairing button on the receiver.

6.1.1 Momentary Mode Setting

In momentary mode, pressing the remote control button turns the relay ON. Releasing the button turns the relay OFF after 3 seconds.

Setting Method:

  1. Press the receiver's learning button 4 times. The red LED light on the receiver will turn on, indicating it has entered the setting state.
  2. Press the desired button on your remote control. The red LED of the receiver will flash and then turn off.
  3. The momentary mode setting is now successful.

6.1.2 Toggle Mode Setting

In toggle mode, pressing the remote control button once turns the relay ON. Pressing the same button again turns the relay OFF after 3 seconds.

Setting Method:

  1. Press the setting button on the "Smart switch" twice. The red indicator light will flash and then light up, entering the setting state.
  2. Press the button on the remote control that needs to be paired. When the red indicator light flashes and goes out, the toggle mode setting is successful.

6.1.3 Latched Mode Setting

In latched mode, one button turns the relay ON, and another button turns it OFF.

Setting Method:

  1. Press the code button on the "Smart switch" 3 times. The red indicator light will flash and then light up, entering the setting state.
  2. Press the function key that is set to turn ON (e.g., button A on the remote). The red indicator light will flash and then stay on.
  3. Then press the function key to turn OFF (e.g., button B on the remote). The red indicator light will flash to confirm that the latch mode is successfully set.

6.1.4 Push Button Mode Setting

This mode allows for a simple push-button operation.

Setting Method:

  1. Press the code setting button on the "Smart switch" 4 times. The red indicator light flashes on the remote control.
  2. When the red indicator light flashes and then goes out, the push button mode is successfully set.

6.1.5 Reset Function (Clearing Remote Control Data)

To clear all stored remote control data from the receiver:

  1. Press the receiver's learning button 8 times.
  2. The red LED will flash a few times, indicating that the clear function is completed.

Note: After clearing the code, all previously paired remote controls will no longer work with the receiver until re-paired.

6.2 External Switch Control (KR2201GS Only)

The KR2201GS can also be controlled using an external mechanical rocker switch. The external switch is used to put the KR2201GS into the remote control learning state.

Diagram showing how to use an external switch for pairing
Using an external switch for pairing.

6.2.1 Toggle Mode Setting (External Switch)

Setting Method:

  1. Connect the power and the light to the KR2201GS.
  2. Press the external switch five times in a row. The light will flash three times and stay on, indicating pairing mode.
  3. Within 5 seconds, press the corresponding button on the remote control to pair. The light will turn off when pairing is complete.

Note: If no pairing occurs within 5 seconds, the load will remain connected and exit pairing mode.

6.2.2 Latch Mode Setting (External Switch)

Setting Method:

  1. Connect the power and the light to the KR2201GS.
  2. Press the external switch 6 times. The light will flash 3 times and then stay on, indicating that it has entered the pairing mode.
  3. Within 5 seconds, press the button on the remote control that you want to set as the "ON" button (e.g., Button A). The load will disconnect and reconnect 3 times, and then stay connected.
  4. Next, press the button on the remote control that you want to set as the "OFF" button (e.g., Button B). The load will disconnect and reconnect 3 times, and then turn off.

Note: If no pairing occurs within 5 seconds, the load will remain connected and exit the pairing mode.

6.2.3 Reset Settings (External Switch)

To clear all remote control data using the external switch:

  1. Ensure the load is either currently on or has been turned on.
  2. Press the external switch 8 times continuously.
  3. The load will momentarily break and then go off. Reset is completed, and all remote control data is cleared.

7. Maintenance

  • Keep the device clean and free from dust.
  • Avoid exposing the device to extreme temperatures or direct sunlight.
  • Regularly check wiring connections for any signs of wear or damage.
  • Replace remote control batteries (AAA) as needed to ensure optimal performance.

8. Troubleshooting

  • Device not responding:
    • Check power supply to the receiver.
    • Ensure remote control batteries are not depleted.
    • Verify that the remote control is properly paired with the receiver according to the operating instructions.
    • If using an external switch, ensure it is a mechanical rocker switch, not an electronic one.
  • Light flickers or does not turn on/off reliably:
    • Check all wiring connections for looseness or corrosion.
    • Ensure the load (e.g., light bulb) is within the maximum load specifications (2200W).
    • Confirm the device is not used with dimmers or in a fully enclosed fixture.
  • Remote control range is poor:
    • Ensure there are no significant obstructions (e.g., thick walls, metal objects) between the remote and the receiver.
    • Replace remote control batteries.
    • The maximum indoor range is approximately 15 meters with partition walls.

9. User Tips

  • The wall panel switches use AAA batteries. Keep spare batteries on hand for uninterrupted use.
  • This device operates on AC (Alternating Current) power (90V-250V), not DC (Direct Current). Ensure your power supply matches this requirement.
  • For optimal performance and longevity, avoid installing the receiver in areas with high humidity or direct exposure to water.

10. Warranty and Support

For detailed product information, troubleshooting, and support, please refer to the official user manual PDF available from the seller. You can typically find this document linked on the product page or by contacting QIACHIP customer support.

A digital copy of the user manual (PDF) can be viewed here.

© 2023 QIACHIP. All rights reserved.

For more information, visit www.qiachip.com


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.