1. Product Overview
This Universal Motorcycle Wireless Anti-theft Alarm System provides enhanced security for your motorcycle, bicycle, or scooter. It features a full waterproof design, remote control operation, adjustable sensitivity, and a loud 125dB alarm siren. The system is designed to deter theft and help locate your vehicle.
Figure 1: Main components of the Anti-theft Alarm System.
Key Features:
- Full waterproof design for the main host unit.
- Remote control operation for arming, disarming, remote start, and vehicle location.
- Control distance up to 150 meters in open areas.
- 5 adjustable sensitivity levels for vibration detection.
- Loud 125dB alarm siren.
- Anti-robbery function to disable the vehicle remotely.
- Compatible with any motorcycle equipped with 12-volt batteries.
Figure 2: Overview of system functionalities.
2. Installation Guide
This alarm system is designed for universal fitment on motorcycles with 12V batteries. Proper installation is crucial for optimal performance and security. It is recommended to have this system installed by a qualified technician if you are unfamiliar with motorcycle electrical systems.
Wiring Instructions:
Connect the alarm system's wires to your motorcycle's electrical system as follows. For a detailed visual wiring diagram, please refer to the official user manual PDF provided by the manufacturer: User Manual (PDF).
- Red Wire: Connect to the positive terminal of the 12V accumulator.
- Black Wire: Connect to the negative terminal of the 12V accumulator (ground).
- Yellow Wires (x2): Connect to the left and right turn signals.
- Orange Wire: Connect to the positive start line.
- Grey Wire (lower flameout): Connect to the ignition generator.
- Pink Wire (upper flameout): Connect to the ignition switch.
- Black and White Wire (flameout line): Connect as per specific motorcycle wiring.
- Antenna: Position the receiving antenna for optimal remote control distance. Improper installation can affect range.
Note: For motorbikes equipped with DC CDI, the pink line connection is not required. The grey line should be connected with the signal trigger line of the igniter.
Placement:
The main alarm unit features a full waterproof design, sealed with a silica gel waterproof ring, allowing for flexible placement on your motorcycle. Ensure the siren is mounted in a secure location where its sound is not obstructed.
Figure 3: The alarm siren features a full waterproof design.
3. Operating Instructions
The system operates using the provided remote controls. Ensure your motorcycle is out of gear when using remote start functions.
Basic Operations:
- Arming the Alarm: Short press the lock key on the remote. The horn will beep once, and the turn signals will flash. The alarm system will be armed after three seconds.
- Disarming the Alarm: When the alarm is armed or ringing, short press the unlock key on the remote. The horn will beep twice, and the turn signals will flash twice. The alarm will be canceled.
- Vibration Triggering Alarm: If the alarm is armed, the first vibration detected will trigger the horn for five seconds, and the engine will be locked. If a second vibration occurs within ten seconds, the alarm will sound for fifteen seconds.
- Emergency Alarm: If the electric lock is turned on while the alarm is armed, the horn will immediately sound loudly.
- Anti-Robbery Function: If a robbery attempt occurs, press the lock key on the remote within range to lock the motor, forcing the motorcycle to stop. The horn will alarm continuously, and turn signals will flash. Press the unlock key to stop the alarm.
- Vehicle Location (Parking Lot Positioning): Short press the bell key on the remote. The horn will sound for fifteen seconds, and the turn signals will flash for fifteen seconds, helping you locate your motorcycle.
- Remote Start (Engine without Key): Double-click the lightning key on the remote. The motorcycle will start immediately. If the engine is cold or idle speed is too slow, repeat the operation.
Figure 4: Remote control operation with a range of up to 150 meters.
Adjusting Vibration Sensitivity:
The system has 5 sensitivity levels. Level 1 is the least sensitive, and Level 5 is the most sensitive. The factory default is Level 3.
- To adjust, long press the bell key on the remote for three seconds. The number of horn beeps indicates the current sensitivity level (e.g., 3 beeps for Level 3).
- Repeat the long press to cycle through the sensitivity levels.
Figure 5: Adjusting the alarm's vibration sensitivity.
4. Maintenance
To ensure the longevity and proper functioning of your anti-theft alarm system, follow these maintenance guidelines:
- Remote Control Care: The remote controls are precision-designed. Avoid dropping them, exposing them to water, excessive heat, or violent vibrations.
- Battery Replacement: If the remote control's operating distance shortens or the indicator light weakens, replace the battery promptly. (The remote controls use standard small batteries, typically CR2032 or similar, though not explicitly stated, it's a common type for such devices).
- Secure Storage: Always keep your remote controls in a safe place to prevent loss or damage.
- Antenna Position: Ensure the main unit's antenna remains properly positioned to maintain optimal remote control range.
- System Power: The main alarm unit has an external power supply and will continue to alarm even after the motorcycle's main power is cut, thanks to its internal power source.
5. Troubleshooting
If you encounter issues with your alarm system, refer to the following troubleshooting steps:
No Response from Remote Control:
- Check if the remote control battery is dead or if the remote control is damaged.
- If both remote controls are unresponsive, check the main engine's fuse for a blown fuse. Also, inspect the copper sheet inside the main engine's plug for tilting.
Motorcycle Alarms by Itself After Arming:
- Verify that the positive (red) and negative (black) lines are correctly connected to the battery.
- Check if the copper sheet inside the main engine's plug is tilted.
- The sensitivity level might be too high. Adjust the sensitivity to a lower level (see Section 3). Note that sensitivity can be affected by the installation position.
Unable to Control Remotely:
- Check if the motorcycle's accumulator (battery) is powered off or has a poor contact.
- If using remote start, ensure the motorcycle's idle speed is not too slow.
6. Specifications
| Feature | Specification |
|---|---|
| Product Type | Wireless Anti-theft Alarm System |
| Compatibility | Universal for Motorcycles, Bicycles, Scooters with 12V batteries |
| Material | ABS |
| Alarm Sound Level | 125dB |
| Remote Control Range | Up to 150 meters (in open area) |
| Sensitivity Levels | 5 (adjustable) |
| Waterproof Design | Full waterproof host unit with silica gel ring |
| Package Dimensions (L x W x H) | 20 cm x 11 cm x 4 cm |
| Package Weight | 0.229 kg |
Package Contents:
- 1 x Alarm Host Unit
- 1 x Siren (Horn)
- 1 x Wiring Harness
- 2 x A1-Type Remote Controls
- 1 x User Manual (Printed)
7. User Tips
Based on common inquiries and user experiences, here are some helpful tips:
- Remote Battery Check: If your remote control seems to have reduced range or is inconsistent, the first step is always to check and replace its battery.
- Vibration vs. Presence Sensors: This system primarily uses vibration detection for its alarm function, not presence sensors. Adjust sensitivity carefully to avoid false alarms.
- Professional Installation: While the manual provides wiring instructions, if you are not confident in your electrical skills, professional installation is highly recommended to prevent damage to the alarm system or your vehicle.
- PDF Manual: Keep the digital PDF version of the user manual handy for detailed wiring diagrams and further reference.
8. Warranty and Support
For any issues not covered in this manual or for warranty claims, please contact your retailer or the manufacturer's customer support. Always refer to the official user manual PDF for the most accurate and detailed information, especially regarding wiring diagrams and specific model variations.
Official User Manual (PDF): Download Here
