Flysky PL18EV Lite, FGr12B

Contents

Flysky PL18EV Lite RC Transmitter and FGr12B Receiver User Manual

For RC Boat, Car, Excavator, and Truck Models

Important Safety Information

⚠ DANGER

  • Keep this product away from flammable materials and open flames. The battery and electronic components are a potential fire hazard if damaged or misused.

⚠ CAUTION

  • Avoid looking directly into the infrared/laser aiming beam, as it may cause eye irritation or damage.
  • Read these instructions carefully before use and retain them for future reference.
  • Do not expose the transmitter or receiver to high temperatures, direct sunlight, or humid environments; this product is intended to be used in dry areas only.
  • The RC model's hull and motor may become hot during prolonged use. Do not touch hot surfaces to avoid burns.
  • Do not operate the RC model near water, swimming pools, or other liquid environments.
CE UK CA 0-3 warning symbol

WARNING: CHOKING HAZARD - Small parts. Not for Children under 3 years.

(Also applies to AVVERTENZA, AVERTISSEMENT, WARNUNG, OSTRZEZENIE in other languages)

What's in the Box

  • 1 x Flysky PL18EV Lite Transmitter
  • 1 x Flysky FGr12B Receiver
Flysky PL18EV Lite Transmitter and FGr12B Receiver
The Flysky PL18EV Lite Transmitter shown with the FGr12B Receiver.

Setup

1. Charging Transmitter Battery

  • The PL18EV Lite Transmitter has a 1S (3.7V) 4300mAh built-in battery. Fully charge it according to the included charging instructions.
  • Charging is via Micro USB.
  • Charging Time: Approximately 4 hours via 5V*2A Micro USB, or 7 hours via 5V*2A wireless charging (if supported).

2. Installing RC Model Batteries

  • Fully charge your RC model's main battery.
  • Install the charged battery into your RC model's battery compartment and secure the cover.

3. Initial Transmitter State

  • Ensure the power switch on the PL18EV Lite Transmitter is in the "OFF" position before connecting or powering on any components.

4. Receiver Binding

  • The FGr12B Receiver is designed to work with transmitters supporting the AFHDS3 protocol (e.g., PL18, NB4, NB4 Lite). Refer to the specific binding instructions provided with your full product manual or the Flysky website for detailed steps on how to bind the receiver to the transmitter. This process typically involves putting both the receiver and transmitter into a binding mode.

Operation

Power On/Off Sequence

  1. To power on: First, turn on the PL18EV Lite Transmitter. Then, power on your RC model.
  2. To power off: First, power off your RC model. Then, power off the PL18EV Lite Transmitter.

Basic Controls

The PL18EV Lite is an 18-channel transmitter. Its joysticks, switches, and dials control various functions of your RC model. Familiarize yourself with the layout and assign functions as per your model's requirements. The 3.5-inch TFT display provides real-time information and allows for configuration of channels, mixing, and other advanced settings.

Front view of Flysky PL18EV Lite Transmitter
Front view of the PL18EV Lite Transmitter, showing controls and display.

Maintenance

Cleaning

  • Use a dry, soft cloth to wipe the exterior of the transmitter and receiver.
  • Do not use water, solvents, or abrasive cleaners, as these can damage the electronic components and finish.

Inspection

  • Regularly inspect the joysticks, switches, and antenna on the transmitter for any signs of wear or damage.
  • Inspect the receiver's antenna and connections for integrity.
  • If your RC model has tracks or complex moving parts, inspect them regularly for debris and remove any dirt or obstructions to ensure smooth movement.

Storage

  • After use, ensure both the RC model and the remote control are powered off.
  • Store the transmitter and receiver in a cool, dry place, away from direct sunlight, high temperatures, and humid environments.
  • Keep the product away from children and pets.

Troubleshooting

No Power / Device Not Turning On

  • Ensure the built-in battery of the PL18EV Lite Transmitter is fully charged. Connect it to a Micro USB power source and check the charging indicator.
  • Verify that the power switch is correctly in the "ON" position.

Loss of Signal / Unresponsive Model

  • Check the battery levels of both the transmitter and the RC model.
  • Ensure the transmitter and receiver are properly bound. If not, refer to the binding instructions.
  • Verify that you are within the specified remote control distance (>500m ground distance).
  • Check for potential interference from other 2.4GHz devices or large metal objects in the operating area.
  • Inspect the antennas on both the transmitter and receiver for damage.

Display Issues

  • If the HVGA 3.5 Inch TFT display is not functioning correctly, try restarting the transmitter.
  • Ensure the device is not exposed to extreme temperatures.

Specifications

Flysky PL18EV Lite Transmitter

FeatureSpecification
Number Of Channels18
Wireless Frequency2.4G
Transmitting Power<20dBm
Wireless ProtocolAFHDS3
Remote Control Distance>500m (ground distance)
Channel Resolution4096
Battery1S (3.7V) 4300mAh (built-in)
Charging InterfaceMicro USB
Charging Time4h@5V*2A (USB) / 7h@5V*2A (wireless charging)
Low Voltage Alarm<3.65V
Antenna TypeDual antenna
DisplayHVGA 3.5 Inch TFT, 320*480
EmulatorUSB Emulator
Data InterfaceUSB, Headphone Port (PPM), Bluetooth Interface (USART)
Temperature Range-10℃ to +60℃
Online UpdateSupport
Size214*120*196mm
WeightApproximately 1006g
CertificationCE, FCC ID:N4ZFGR12B

Flysky FGr12B Receiver

FeatureSpecification
Product ModelFGr12B
Adaptive TransmitterAll transmitters supporting AFHDS3 (PL18, NB4, NB4 Lite, etc.)
Model TypeCar/Boat etc.
PWM Channels11 (Version 2.0 will be upgraded to 12 channels)
RF2.4GHZ
2.4G ProtocolAFHDS3
AntennaSingle Antenna
Input Power3.5-9V
Data OutputPWM\PPM\i-bus in
Temperature Range-10℃ to +60℃
Humidity Limit20%-95%
Online UpdateYes
Dimensions37 x 25 x 17.5mm
Weight11.2g

User Tips

  • Language Settings: The PL18EV Lite transmitter features a 3.5-inch TFT display. If you need to change the display language, navigate through the system settings menu on the transmitter. Consult the full user manual for detailed instructions on accessing and modifying language preferences.

Warranty and Support

User Manual (PDF)

A comprehensive user manual in PDF format is available for detailed instructions and advanced features. You can view or download it from the following link:

Flysky PL18EV Lite User Manual (PDF)

Warranty Information

For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact the seller/manufacturer directly. Keep your proof of purchase for any warranty claims.

Technical Support

For technical assistance, firmware updates, or further inquiries, please visit the official Flysky website or contact their customer support channels.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.