Introduction
The PETKIT EVERSWEET SOLO Smart Pet Water Fountain is designed to provide fresh, filtered water for your cats and small dogs. Featuring a smart LED light indicator, a triple filtration system, and silent operation, it aims to promote your pet's hydration and urinary health. This manual provides essential information for the proper setup, operation, and maintenance of your new pet water fountain.
Image: PETKIT EVERSWEET SOLO Smart Pet Water Fountain (Gray)
Specifications
| Feature | Detail |
|---|---|
| Product Name | PETKIT EVERSWEET SOLO Smart Pet Drinking Fountain |
| Model | EVERSWEET SOLO |
| Dimensions (L x W x H) | 160mm x 160mm x 158mm |
| Material | ABS Plastic |
| Capacity | 1.85 Liters (63 oz) |
| Power Source | USB Charge (5V operating voltage) |
| Input Voltage | 110-240V (for power adapter) |
| Min Output | 50g |
| Max Output | 300g |
| LCD Display | No |
| Features | Automatic, Sustainable, Smart LED Light, Triple Filtration System, Silent Operation (<30dB) |
| Suitable For | Cats and Small to Medium Pets |
| Included | Fountain Host Unit, 1 Filter, USB Charging Cable |
Setup Guide
Follow these steps to set up your PETKIT EVERSWEET SOLO Smart Pet Water Fountain:
- Unpack and Clean: Carefully remove all components from the packaging. Wash the water tank, tray, and pump thoroughly with water and mild soap. Rinse well to remove any soap residue.
- Install Filter: Soak the new filter in clean water for 5-10 minutes before first use. Place the pre-soaked filter into the designated filter slot in the fountain.
- Fill Water Tank: Fill the water tank with clean tap water up to the MAX fill line. Do not overfill.
- Assemble Fountain: Place the top tray onto the water tank, ensuring it is securely seated.
- Connect Power Cord: Refer to the diagram below for proper power cord installation. Connect the USB cable to the power port at the bottom of the main unit. Align the power cord with the groove and press it firmly into place to secure it. Connect the other end of the USB cable to a compatible 5V USB power adapter (not always included) and plug it into a wall outlet.
Image: Product features and power cord installation guide. This image illustrates the triple filtration system, silent operation, smart LED light indicators, and a step-by-step guide for connecting the USB power cable to the fountain base and securing it in the groove.
Operating Instructions
Once assembled and powered on, the PETKIT EVERSWEET SOLO will begin dispensing water. The fountain is designed for continuous, silent operation, simulating natural springs to encourage your pet to drink more.
Smart LED Light Indicators:
- Water Level Indicator: The LED light will indicate the current water level. A specific color or flashing pattern (refer to the product's quick start guide if available for exact patterns) will alert you when the water level is low and needs refilling.
- Filter Replacement Reminder: The LED light will also serve as a reminder for filter replacement, typically after a set period of use (e.g., 30 days). A change in light color or pattern will signal that it's time to replace the filter.
The fountain operates at a low noise level (below 30dB), ensuring it does not disturb your pets or household.
Maintenance
Regular maintenance is crucial for the longevity of your fountain and the health of your pet.
Cleaning:
- Weekly Cleaning: Disassemble the fountain and clean all components (water tank, tray, pump) with water and mild soap. Pay special attention to the pump to prevent mineral buildup and ensure proper function. Rinse thoroughly.
- Pump Cleaning: The pump should be cleaned regularly to prevent clogs from pet hair or debris. Disassemble the pump according to its specific instructions (usually involves removing the cover and impeller) and clean all parts.
Filter Replacement:
- The PETKIT EVERSWEET SOLO uses a triple filtration system (filter cotton, activated carbon, ion exchange resin) to purify water.
- Replace the filter approximately every 2-4 weeks, or as indicated by the smart LED light reminder, depending on water quality and the number of pets using the fountain.
- Always pre-soak new filters for 5-10 minutes before installation.
Troubleshooting
- Fountain Not Dispensing Water:
- Check if the power adapter is securely plugged into the wall outlet and the USB cable is properly connected to the fountain.
- Ensure the water level is above the minimum line. Refill if necessary.
- Clean the pump. Debris or pet hair can clog the pump, preventing water flow.
- Excessive Noise:
- Check the water level. Low water levels can cause the pump to make more noise.
- Clean the pump. A dirty pump can vibrate and create noise.
- Ensure the fountain is placed on a flat, stable surface.
- LED Light Not Working/Incorrectly Indicating:
- Verify power connection.
- If the filter reminder light is on, replace the filter and reset the indicator (if applicable, refer to specific product instructions for reset procedure).
User Tips
- Encourage Drinking: Place the fountain in an easily accessible and quiet location where your pet feels comfortable drinking. Some pets may need time to adjust to a new fountain.
- Monitor Water Level: Regularly check the water level and refill as needed to ensure continuous fresh water supply and prevent pump damage. The smart LED light will assist with this.
- Regular Cleaning: Adhere to the recommended cleaning schedule to maintain hygiene and prevent bacterial growth or mineral buildup.
- Filter Maintenance: Always keep spare filters on hand and replace them promptly when indicated to ensure optimal water quality.
Warranty and Support
For warranty information, technical support, or replacement parts, please contact the retailer or manufacturer directly. Keep your purchase receipt as proof of purchase.
