Flysky FS-iA6, FS-iA6B, FS-iA10B, FS-X6B

Contents

FlySky RC Receiver Instruction Manual

Models: FS-iA6, FS-iA6B, FS-iA10B, FS-X6B

1. Introduction

This manual provides essential information for the safe and effective use of your FlySky RC receiver. Please read it thoroughly before operation and retain it for future reference.

1.1 Package Contents

  • Main product (FlySky RC Receiver) × 1
  • User Manual × 1

2. Safety Warnings

WARNING:

  • Keep away from fire, high temperature, and humidity.
  • Keep out of reach of children and infants.
  • Choking hazard – small parts, not for children under 3 years.
  • Do not disassemble, modify, or repair the product.
  • Stop use immediately if the product is damaged.

3. Receiver Models Overview

This manual covers multiple FlySky receiver models. Please identify your specific model for detailed specifications and compatibility.

Overview of FlySky FS-X6B, FS-iA10B, FS-iA6, and FS-iA6B receivers
Figure 1: Overview of FlySky FS-X6B, FS-iA10B, FS-iA6, and FS-iA6B receivers

3.1 FlySky FS-iA6 Receiver

The FS-iA6 is a 6-channel receiver designed for various RC aircraft. It operates on the 2.4 GHz band using FlySky's Automatic Frequency Hopping Digital System (AFHDS).

FlySky FS-iA6 receiver with bind plug
Figure 2: FlySky FS-iA6 receiver with bind plug

3.2 FlySky FS-iA6B Receiver

The FS-iA6B is an enhanced 6-channel receiver featuring dual antennas for improved signal reception and i-BUS/data acquisition interfaces. It is compatible with a range of FlySky transmitters.

Angled view of FlySky FS-iA6B receiver
Figure 3: Angled view of FlySky FS-iA6B receiver

3.3 FlySky FS-iA10B Receiver

The FS-iA10B is a 10-channel receiver with dual antennas, i-BUS, and data acquisition capabilities, suitable for more complex RC models requiring additional channels.

FlySky FS-iA10B receiver with bind plug
Figure 4: FlySky FS-iA10B receiver with bind plug

3.4 FlySky FS-X6B Receiver

The FS-X6B is a compact 6-channel (PWM) / 18-channel (i-BUS) two-way receiver specifically designed for multi-rotor aircraft. It supports PWM, PPM, and i-BUS outputs, and includes a voltage sensor interface.

Top view of FlySky FS-X6B receiver board
Figure 5: Top view of FlySky FS-X6B receiver board

4. Setup and Binding

The binding process links your receiver to your transmitter, establishing a secure communication channel.

4.1 General Binding Procedure

  1. Prepare Transmitter: Refer to your transmitter's user manual for specific instructions on how to enter binding mode.
  2. Power on Receiver: While holding the bind button on the receiver, power on the receiver.
  3. Observe LED: If the receiver's LED is flashing, it indicates that it has entered bind mode.
  4. Complete Binding: After successful binding, the transmitter will typically return to its previous menu. The receiver's LED will stop flashing and remain solid.
  5. Verify Functionality: Check if all model controls and receiver functions work as expected. If not, restart the binding procedure.

Note: For FS-X6B, the binding process is as described above. Ensure all cables are correctly connected to the PWM, PPM, i-BUS, and Voltage sensor ports as required for your setup.

FlySky FS-X6B receiver board with connected wires
Figure 6: FS-X6B receiver board with connected wires

5. Operation

Once bound, your receiver will communicate with your transmitter to control your RC model. Ensure your transmitter is configured correctly for the number of channels and output types (PWM, PPM, i-BUS) supported by your specific receiver model.

  • Channels: Connect servos and other components to the corresponding channel ports on the receiver.
  • 2.4G Modes: All receivers utilize FlySky's AFHDS 2A system for reliable and interference-free communication.
  • i-BUS/PPM: For models supporting i-BUS or PPM, connect the appropriate signal port to your flight controller or other compatible device.
  • Voltage Sensor (FS-X6B, FS-iA6B, FS-iA10B): These models may offer external voltage sensing capabilities. Refer to your flight controller or model's documentation for integration.

6. Maintenance

  • Keep the product clean and dry.
  • Store in a cool and dry place.
  • Avoid strong pressure, dropping, or collision.

7. Troubleshooting

7.1 No Signal / Loss of Control

  • Re-bind Receiver: Follow the binding procedure in Section 4.1 to ensure the receiver is correctly linked to the transmitter.
  • Check Power: Ensure the receiver is receiving adequate power (4.0-6.5V DC).
  • Antenna Placement: Verify antennas are correctly positioned and not obstructed by carbon fiber or metal parts. For dual antenna models, ensure they are oriented at 90 degrees to each other for optimal reception.
  • Transmitter Compatibility: Confirm your transmitter is compatible with the receiver's protocol (AFHDS 2A).

7.2 Incorrect Channel Response

  • Check Wiring: Ensure servos and other components are connected to the correct channel ports.
  • Transmitter Settings: Verify channel mapping and mixing settings on your transmitter.

8. Specifications

FeatureFS-iA6FS-iA6BFS-iA10BFS-X6B
Channels66106 (PWM), up to 18 (i-BUS)
Frequency Range2.4-2.48 GHz2.4055-2.475 GHz2.4055-2.475 GHz2.4055-2.475 GHz
Number of Bands140140140140
Transmitting Power≤ 20dBm≤ 20dBm≤ 20dBm≤ 20dBm
Receiver Sensitivity-105dBm-105dBm-105dBm-105dBm
2.4G ModeAFHDS 2AAFHDS 2AAFHDS 2AAFHDS 2A
EncodingGFSKGFSKGFSKGFSK
Antenna Length26mm * 226mm * 226mm * 2Dual omnidirectional
Input Power4.0-6.5V DC4.0-6.5V DC4.0-6.5V DC4.0-6.5V DC
Dimensions (mm)40.4 x 21.1 x 7.3547 x 26.2 x 1551 x 34 x 1537 x 22 x 7
Weight6.4g14.9g19.3g5g
i-BUS InterfaceNoYesYesYes
Data Acquisition InterfaceNoYesYesNo
UsageRC Airplane / Glider / HelicopterRC Airplane / Glider / HelicopterRC Airplane / Glider / HelicopterMulti-rotor aircraft
CertificationCE0678, FCCCE0678, FCCCE0678, FCCCE0678, FCC
Compatible TransmittersFS-i10, FS-i6, FS-i4, FS-GT2F, FS-GT2E, FS-GT2BFS-i4, FS-i6, FS-i10, FS-GT2E, FS-GT2GFS-i4, FS-i6, FS-i6S, FS-i10, FS-iT4SAll AFHDS 2A Transmitters (e.g., FS-i10, FS-i8, FS-i6, FS-i6S, FS-i6X, FS-i4, FS-i4X)

9. User Tips

  • Verify Transmitter Compatibility: Always double-check that your specific FlySky transmitter model is listed as compatible with your chosen receiver. Incompatible transmitters will prevent proper binding and operation.
  • Antenna Orientation: For receivers with dual antennas, ensure they are mounted at a 90-degree angle to each other to maximize signal diversity and range.
  • Environmental Factors: Avoid operating your RC model in areas with high electromagnetic interference, which can affect receiver performance.

10. Warranty and Support

10.1 Compliance Information

  • CE Compliance: This product complies with EU safety and environmental protection standards.
  • FCC Statement: This device complies with Part 15 of FCC Rules.
  • RoHS: This product is RoHS compliant.

10.2 After-Sale Service

For any after-sales problems or technical support, please contact the seller via the AliExpress platform. Provide your order details and a clear description of the issue for prompt assistance.

Manufactured in China.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.