FLYSKY FS-CEV04

Contents

FLYSKY FS-CEV04 Four Channel Expansion Module Instruction Manual

Model: FS-CEV04 | Brand: FLYSKY

Introduction

The FLYSKY FS-CEV04 is a four-channel expansion module designed to extend the capabilities of compatible FLYSKY FGr series receivers. This module adds four additional channel outputs, allowing for more control functions in your remote-controlled car, ship, or aircraft models. It is compact, lightweight, and integrates seamlessly with supported receivers.

Compatibility

The FS-CEV04 module is compatible with the following FLYSKY receivers:

  • FGr4
  • FGr4S
  • FGr4P
  • FGr4B
  • FGr8B
  • FGr12B

It is suitable for use with various remote control models including cars, ships, and aircraft.

Transmitter/Receiver Pairing Chart

Refer to the following table for detailed compatibility between FLYSKY transmitters and receivers. A checkmark (✓) indicates compatibility.

FLYSKY Transmitter and Receiver Compatibility Chart
Image: FLYSKY Transmitter and Receiver Compatibility Chart. This table details which FLYSKY transmitters are compatible with various receivers across AFHDS3, AFHDS2A, AFHDS2, and AFHDS protocols.
Transmitter/Receiver Pairing Table
ReceiverAFHDS3AFHDS2AAFHDS2AFHDS
PL18FTr16SFTr10FGr4FGr4SFGr4PLA10X14SX8BA8SIA10BIA6BIA6A3BS4IA10IR6BIR4IR4BBS3R9BR6BR6CGR3EGR3F
PL18✓✓✓✓✓✓
FRM301✓✓
FRM302✓✓
FS-L13✓
NB4✓✓✓✓✓✓
NV14✓✓✓✓✓✓✓✓✓
FS-i10✓✓✓✓✓✓✓✓✓
FS-i8✓✓✓✓✓✓✓✓✓
FS-i6S✓✓✓✓✓✓✓✓✓
FS-i6X✓✓✓✓✓✓✓✓✓
FS-i6✓✓✓✓✓✓✓✓✓
FS-i4X✓✓✓✓✓✓✓✓✓
FS-i4✓✓✓✓✓✓✓✓✓
FS-TH9X✓✓✓✓✓✓✓✓✓
RM003✓✓✓✓✓✓✓✓✓
FS-T6✓✓✓✓
FS-CT6B✓✓✓✓
FS-T4B✓✓✓✓
FS-GT5✓✓✓✓✓✓✓✓✓
FS-iT4S✓✓✓✓✓✓✓✓✓
FS-iT4✓✓✓✓✓✓✓✓✓
FS-GT2E✓✓✓✓✓✓✓✓✓
FS-GT2F✓✓✓✓✓✓✓✓✓
FS-GT2G✓✓✓✓✓✓✓✓✓
FS-GT2B✓✓✓✓✓✓✓✓✓
FS-GT3B✓✓✓✓✓✓✓✓✓
FS-GT3C✓✓✓✓✓✓✓✓✓

Setup and Installation

Follow these steps to correctly install and connect your FS-CEV04 expansion module:

  1. Identify Ports: Locate the IN, OUT, VCC, C1, C2, C3, C4, K1, K2, K3, K4, and LED indicators on the FS-CEV04 module.
  2. Connect to Receiver: Connect the "IN" port of the FS-CEV04 module to an available channel on your compatible FLYSKY receiver (e.g., FGr4, FGr4S, etc.). Ensure correct polarity (signal, positive, negative).
  3. Power Connection: The module draws power from the receiver. Ensure your receiver is powered within the specified input voltage range of 4.0-6.5V DC.
  4. Connect Servos/Devices: Connect your additional servos or devices to the C1, C2, C3, and C4 output ports on the FS-CEV04 module. These ports provide the additional four channels.
  5. I-BUS Interface: If your setup utilizes the I-BUS protocol, the module features an I-BUS interface (FUTABA-3PIN * 2.54MM) for advanced connectivity.

Connection Diagram

FLYSKY FS-CEV04 Wiring Diagram
Image: FLYSKY FS-CEV04 Wiring Diagram. This image illustrates how to connect the FS-CEV04 module to a compatible receiver, showing the input and output connections for additional channels.
FLYSKY FS-CEV04 Module Overview
Image: FLYSKY FS-CEV04 Module Overview. A detailed view of the FS-CEV04 module, highlighting its various ports and indicators including VCC, C1-C4, K1-K4, LED, IN, and OUT.

Operating Instructions

Once the FS-CEV04 module is correctly installed and connected to your receiver, it will automatically provide four additional output channels (C1-C4). These channels can be used to control various auxiliary functions on your RC model, such as lights, winches, gear shifts, or other proportional/switched devices, depending on your transmitter's capabilities and programming.

  • Channel Assignment: The specific function assigned to each of the four new channels (C1-C4) will be determined by your transmitter's programming and how you configure your model. Refer to your transmitter's manual for details on assigning auxiliary channels.
  • LED Indicator: The LED on the module indicates its operational status. A steady light typically signifies normal operation.
  • Key Inputs (K1-K4): The K1-K4 inputs are likely for specific control signals or configuration, depending on the advanced features of your receiver and transmitter system. Consult your receiver's manual for detailed usage of these inputs.

Maintenance

  • Keep Clean: Regularly inspect the module for dust or debris. Use a soft, dry brush or compressed air to clean it.
  • Avoid Moisture: Protect the module from water and excessive humidity to prevent damage to electronic components.
  • Secure Connections: Ensure all wiring connections are secure and free from strain. Loose connections can lead to intermittent operation or damage.
  • Storage: When not in use, store the module in a dry, cool place away from direct sunlight and extreme temperatures.

Troubleshooting

  • No Response from New Channels:
    • Check all connections to ensure they are secure and correctly oriented (polarity).
    • Verify that the FS-CEV04 module is connected to a compatible receiver.
    • Confirm that your transmitter is correctly configured to send signals to the auxiliary channels and that these channels are assigned to the corresponding outputs on the FS-CEV04.
    • Ensure the receiver is receiving power and is properly bound to the transmitter.
  • LED Not Lit:
    • Check the power supply to the receiver and ensure it is within the 4.0-6.5V DC range.
    • Inspect the connection between the FS-CEV04 and the receiver for any breaks or shorts.
  • Intermittent Operation:
    • Check for loose wiring or damaged cables.
    • Ensure the module is not exposed to excessive vibration or electromagnetic interference.

Specifications

FeatureSpecification
Model NumberFS-CEV04
Brand NameFLYSKY (XINQIRC)
Adapted ReceiversFGr4, FGr4S, FGr4P, FGr4B, FGr8B, FGr12B
Number of Extended Channels4
Suitable Model TypesCar, Ship, Aircraft
Static Working Current9mA (TYPE)
Body Weight8.1 grams
Input Power Supply4.0-6.5V DC
External Dimensions30 * 25.6 * 13mm
Appearance ColorBlack
I-BUS InterfaceYes (FUTABA-3PIN * 2.54MM)
MaterialComposite Material
Recommend Age14+y

User Tips

  • Channel Mapping: Before connecting any devices, plan out which auxiliary functions you want to control and map them to the C1-C4 outputs in your transmitter's settings.
  • Power Considerations: While the module itself has low current draw, ensure your main receiver and power source can handle the additional current draw from any servos or devices connected to the expansion module's outputs.
  • Secure Mounting: Mount the FS-CEV04 module securely within your model to prevent movement and potential damage from vibrations during operation.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact the original seller or the manufacturer, FLYSKY. Keep your purchase receipt as proof of purchase.

© 2023 FLYSKY. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.