1. Introduction
The FLYSKY FS-SR8C is an 8-channel 2.4G receiver designed for various remote-controlled models, including fixed-wing aircraft, delta-wing airplanes, gliders, and robots. It utilizes the advanced ANT protocol, ensuring reliable communication with compatible FLYSKY transmitters such as the FS-ST8. This manual provides essential information for the safe and effective setup, operation, and maintenance of your FS-SR8C receiver.
2. Safety Information
- Always operate your RC model in open areas, away from people, vehicles, and obstacles.
- Ensure all connections are secure before powering on your model.
- Verify correct polarity when connecting power to the receiver. Incorrect polarity can cause damage.
- Keep antennas clear of carbon fiber or metal parts to avoid signal interference.
- Regularly inspect the receiver and wiring for any signs of damage or wear.
- Do not attempt to modify the receiver, as this may void the warranty and compromise safety.
3. Package Contents
Upon opening your FS-SR8C package, you should find the following items:
- 1 x FLYSKY FS-SR8C Receiver
- 2 x Small Connectors (for servo/power connections)
- 1 x Binding Plug

4. Specifications
| Feature | Specification |
|---|---|
| Product Name | FS-SR8C |
| Compatible Transmitters | Adapts transmitters with ANT protocol (e.g., FS-ST8) |
| Compatible Models | Fixed-wing aircraft, delta-wing airplanes, gliders, robots |
| PWM Channels | 8 |
| RF Frequency | 2.4GHz ISM |
| Maximum Power | < 20dBm (e.i.r.p.) (EU) |
| 2.4G Protocol | ANT |
| Resolution | 4096 |
| Antenna | Dual antennas (ipex4) |
| Distance | > 800m (Air distance without interference) |
| Input Power | 3.5~9V/DC |
| Working Current | 70mA (at 5V) |
| Data Output | PWM/PPM/i-BUS/S.BUS |
| Online Update | Yes |
| Temperature Range | -10℃ ~ +60℃ |
| Humidity Range | 20% ~ 95% |
| Dimensions | 22*15*3mm (Excluding pins and antennas) |
| Weight | 1g (Excluding pins and antennas), 2g (Including 4*3 pins and two antennas) |
| Certifications | CE, FCC ID: 2A2UNSR8C00 |
5. Setup
5.1. Receiver Layout and Pinout
The FS-SR8C receiver features multiple pins for power, signal, and various output protocols. Refer to the diagram below for the pin assignments.

- S+-: Standard servo connection (Signal, Positive, Negative).
- 1/PPM: Channel 1 PWM output, also supports PPM output.
- LED: Status indicator light.
- 2-8: PWM output channels 2 through 8.
- SENS: Sensor input (if applicable for telemetry).
- BVD: Battery Voltage Detection input.
5.2. Binding Procedure
To establish communication between your FS-SR8C receiver and a compatible FLYSKY ANT protocol transmitter (e.g., FS-ST8), follow these steps:
- Ensure your transmitter is powered off.
- Insert the binding plug into the 'BVD' port on the FS-SR8C receiver.
- Connect power to any available 'S+-' port on the receiver (e.g., via an ESC or separate battery). The receiver's LED should start flashing rapidly, indicating it is in binding mode.
- While holding the 'BIND' button on your transmitter (or following its specific binding procedure), power on the transmitter.
- The receiver's LED should stop flashing and remain solid, indicating a successful bind.
- Power off both the receiver and the transmitter.
- Remove the binding plug from the receiver.
- Power on the transmitter first, then the receiver. The receiver's LED should be solid, confirming the connection.
- Test all channels to ensure proper control before flight or operation.
5.3. Antenna Installation
The FS-SR8C features dual antennas for improved signal reception and reliability. Proper antenna placement is crucial for optimal range and performance:
- Mount the antennas at a 90-degree angle to each other. This diversity setup helps ensure continuous signal reception regardless of the model's orientation.
- Keep the antenna tips as far away as possible from any carbon fiber, metal, or other conductive materials that could shield the signal.
- Ensure the active part of the antenna (the last 31mm of the wire, without the outer insulation) is exposed and not bent sharply.
- Secure the antennas to prevent them from moving during operation.
6. Operating Instructions
6.1. Powering On and Signal Check
- Always power on your transmitter first.
- Then, power on your RC model, which will power the receiver.
- Observe the receiver's LED. A solid LED indicates a successful connection with the transmitter. A flashing LED indicates no signal or binding issue.
- Before operating, perform a range check according to your transmitter's manual to ensure adequate signal strength.
6.2. Data Output Modes
The FS-SR8C supports multiple data output modes:
- PWM (Pulse Width Modulation): Standard output for individual servos and ESCs. Each channel has its own pin.
- PPM (Pulse Position Modulation): A single wire carries all channel data, often used for flight controllers. This is available on the '1/PPM' pin.
- i-BUS/S.BUS: Serial bus protocols that transmit all channel data over a single wire, offering lower latency and simpler wiring for compatible flight controllers or devices. Consult your flight controller's manual for connection details.
The specific output mode can usually be configured via your compatible FLYSKY transmitter's settings.
7. Maintenance
- Keep the receiver clean and free from dust, dirt, and moisture.
- Avoid exposing the receiver to extreme temperatures or direct sunlight for prolonged periods.
- Regularly check all wiring and connectors for signs of wear, corrosion, or damage. Replace any damaged components immediately.
- Ensure the antennas are not kinked or damaged.
- Store the receiver in a dry, cool place when not in use.
8. Troubleshooting
- No Signal (LED flashing):
- Ensure the receiver is correctly bound to the transmitter. Repeat the binding procedure if necessary.
- Check that the transmitter is powered on and operating on the correct protocol (ANT).
- Verify power supply to the receiver is within the specified range (3.5-9V DC) and correctly connected.
- Short Range or Intermittent Signal:
- Check antenna placement and orientation. Ensure they are at 90 degrees to each other and clear of obstructions.
- Inspect antennas for damage.
- Avoid operating near large metal objects, power lines, or other sources of RF interference.
- Ensure the transmitter's battery is fully charged.
- Servos Not Responding:
- Verify that the receiver is successfully bound and receiving a signal (solid LED).
- Check servo connections to the correct PWM channels.
- Ensure servos are powered correctly.
- Test servos individually to rule out faulty servos.
- Receiver Not Powering On:
- Check power source (ESC, battery) and its connections to the receiver.
- Verify correct polarity of the power connection.
9. User Tips
- Antenna Orientation: For optimal signal reception, always ensure your dual antennas are mounted at a 90-degree angle to each other. This helps maintain a strong signal regardless of your model's attitude.
- Firmware Updates: Periodically check the official FLYSKY website for any available firmware updates for your FS-SR8C receiver. Updates can improve performance, add features, or fix bugs.
- Pre-Flight Checks: Always perform a thorough pre-flight check, including range testing and verifying all control surfaces respond correctly, before operating your model.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please contact the original seller or the manufacturer directly. Keep your proof of purchase for any warranty claims.
11. Certifications
The FLYSKY FS-SR8C receiver complies with the following certifications:
- CE: Conforms to European Union health, safety, and environmental protection standards.
- FCC ID: 2A2UNSR8C00: Certified by the Federal Communications Commission for electromagnetic compatibility in the United States.
