1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the A-OK AC227-13 DC Route Radio Receiver Wall Curtain Switch. This device is designed to control motorized curtains or blinds, offering both local wall switch control and remote RF433 control when paired with compatible A-OK remote controllers. The AC227-13 is an updated version of the AC227-11, retaining the same core functionality. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Product Overview
The A-OK AC227-13 is a versatile single-channel DC route radio receiver integrated into a wall-mounted switch. It allows for direct control of DC motors for curtains or blinds via its front panel buttons (Up, Stop, Down) and can also receive commands from A-OK brand RF433MHz remote controllers. The unit is designed for installation in standard 86-type wall bottom boxes.
3. Specifications
| Feature | Detail |
|---|---|
| Model Number | AC227-13 |
| Frequency | RF433.92MHz |
| Input Voltage | 100-150VAC 60Hz, 190-240VAC 50Hz |
| Output Current (100-150VAC Input) | 24VDC/4.6A |
| Output Current (190-240VAC Input) | 24VDC/7.0A |
| Wind/Light/Rain Sensor Power | 12VDC/0.2A |
| Control Type | Single Channel DC Controller |
| Compatibility | Designed for 86 bottom box; RF433 control compatible only with A-OK brand remote controllers. |
| Battery Included | No |
| Origin | Mainland China |
4. Installation and Wiring
Safety Warning: Installation should be performed by a qualified electrician in accordance with local electrical codes. Ensure power is disconnected at the main circuit breaker before beginning any electrical work.
- Prepare the Installation Site: The AC227-13 is designed to fit into a standard 86-type wall bottom box. Ensure adequate space and proper wiring access.
- Wiring Connections: Refer to Figure 3 for the wiring diagram and terminal labels on the back of the receiver. Carefully connect the wires to the corresponding terminals.
Wiring Terminal Details:
- 交流输入 (AC Input):
- 火 (Live)
- 零 (Neutral)
- 手控输入 (Manual Control Input):
- 上 (Up)
- 下 (Down)
- 停 (Stop)
- 风光雨 (Wind/Light/Rain Sensor Input):
- GND
- 12V
- M+
- M-
- 电机输出 (Motor Output):
- M+
- M-
- Secure the Device: Once wiring is complete, carefully place the receiver into the wall box and secure the front panel.
- Power On: Restore power to the circuit. The LED indicator on the front panel should illuminate, indicating the device is powered.
5. Operating Instructions
5.1. Manual Control (Wall Switch)
The front panel of the AC227-13 features three buttons for direct control:
- Up Arrow Button: Press to raise the curtain/blind.
- Middle Bar Button: Press to stop the curtain/blind at its current position.
- Down Arrow Button: Press to lower the curtain/blind.
5.2. Remote Control (RF433)
The AC227-13 is compatible with A-OK brand RF433MHz remote controllers (e.g., AC123 series). To use remote control, the remote must first be paired with the receiver.
Pairing Instructions (General):
Specific pairing instructions may vary slightly depending on the remote controller model. Generally, the process involves:
- Ensure the AC227-13 receiver is powered on.
- Locate the pairing button or sequence on the AC227-13 (often a small button on the side or back, or a specific button press combination on the front panel).
- Activate the pairing mode on the receiver (e.g., press and hold the pairing button until an indicator light flashes).
- Within a short timeframe, press a button on your A-OK remote controller (e.g., the 'Stop' button or a dedicated pairing button on the remote).
- The receiver's indicator light should change (e.g., stop flashing, turn solid) to confirm successful pairing.
Refer to your specific A-OK remote controller's manual for precise pairing steps.
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the surface of the wall switch. Do not use abrasive cleaners or solvents.
- Environment: Ensure the device is installed in a dry environment, away from direct moisture or extreme temperatures.
- Inspection: Periodically check wiring connections for any signs of wear or looseness.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device not responding to wall switch buttons. | No power; incorrect wiring; internal fault. | Check power supply. Verify wiring connections. If problem persists, contact support. |
| Device not responding to remote control. | Remote not paired; remote battery low; interference. | Ensure remote is paired (refer to pairing instructions). Replace remote battery. Reduce potential RF interference. |
| Motor operates erratically or not fully. | Motor limits not set; motor fault; power fluctuation. | Check motor's own limit settings. Ensure stable power supply. |
8. User Tips
- For optimal RF performance, ensure the receiver is not obstructed by large metal objects or other sources of strong electromagnetic interference.
- When installing, double-check all wiring connections to prevent short circuits or damage to the unit.
- If using multiple A-OK RF433 devices, ensure each remote is correctly paired to its intended receiver to avoid unintended operation.
9. Warranty and Support
The A-OK AC227-13 DC Route Radio Receiver Wall Curtain Switch comes with a 1-year manufacturer's limited warranty for defective items from the date of receipt. Accessories are covered by a 3-month warranty. This warranty does not cover items damaged or misused after receipt.
For warranty claims, technical support, or any inquiries, please contact your seller with your order number and a detailed description of the issue. Defective items must be reported and returned within the warranty period, in their original packaging if possible.
