Shark LZ600 LZ601 LZ602 LZ602C

Contents

Instruction Manual: Replacement Parts Kit for Shark LZ600 Series Vacuum Cleaners

Models: LZ600, LZ601, LZ602, LZ602C

1. Product Overview

This replacement parts kit is designed for Shark APEX UpLight LZ600 series vacuum cleaners, including models LZ600, LZ601, LZ602, and LZ602C. The kit provides essential components to maintain your vacuum's optimal cleaning performance and air filtration.

1.1. Included Components

  • Soft Brush Roll (DuoClean Brush)
  • Pre-Motor Foam Filters
  • Pre-Motor Felt Filters
  • Post-Motor HEPA Filter
  • Cleaning Brush Tool
Complete replacement parts kit for Shark LZ600 series vacuums

Figure 1: Overview of the Replacement Parts Kit

2. Setup and Installation

Before installing any replacement parts, ensure your vacuum cleaner is unplugged from the power outlet to prevent accidental operation.

2.1. Replacing the Soft Brush Roll

  1. Lay the vacuum cleaner flat and locate the brush roll access cover on the bottom of the floor nozzle.
  2. Use a coin or screwdriver to unlock the fasteners on the brush roll cover.
  3. Remove the old brush roll.
  4. Insert the new soft brush roll, ensuring it is properly seated in the designated slots.
  5. Replace the brush roll cover and secure the fasteners.
Brush roll installed in a vacuum cleaner head

Figure 2: Brush Roll Installation Example

2.2. Replacing Pre-Motor Filters (Foam and Felt)

  1. Remove the dust cup from the vacuum cleaner.
  2. Locate the pre-motor filter housing, usually beneath the dust cup.
  3. Remove the old foam and felt filters.
  4. Place the new felt filter first, followed by the new foam filter, ensuring they fit snugly.
  5. Reattach the dust cup.
Pre-motor filter

Figure 3: Pre-Motor Filter

2.3. Replacing the Post-Motor HEPA Filter

  1. Locate the post-motor filter cover, typically on the front or side of the vacuum's main body.
  2. Open the cover and remove the old HEPA filter.
  3. Insert the new HEPA filter, ensuring it is correctly oriented and seated.
  4. Close the filter cover securely.
Post-motor HEPA filter

Figure 4: Post-Motor HEPA Filter

Diagram showing filter replacement steps

Figure 5: General Filter Replacement Diagram

3. Operating Principles

These replacement parts are crucial for the effective operation of your Shark vacuum cleaner:

  • The Soft Brush Roll is designed to effectively pick up hair, pet fur, dander, and fine dust from various floor types, ensuring thorough cleaning in crevices and corners.
  • The Pre-Motor Foam and Felt Filters protect the vacuum motor from dust and debris, extending its lifespan and maintaining suction power.
  • The Post-Motor HEPA Filter captures 99.9% of dust and allergens, ensuring that the air expelled from the vacuum is clean and fresh.

4. Maintenance

Regular maintenance of your vacuum's filters and brush roll is essential for optimal performance and longevity.

4.1. Filter Cleaning

  • Pre-Motor Filters (Foam and Felt): These should be rinsed with clean water every 2-4 weeks, or more frequently with heavy use. Squeeze out excess water and allow them to air dry completely for at least 24 hours before reinstallation. Do not use a washing machine or dryer.
  • Post-Motor HEPA Filter: This filter should be tapped clean periodically to remove loose dust. It can also be rinsed with water, but only when visibly dirty. Ensure it is completely dry for at least 24 hours before reinstallation.

Important: Always ensure filters are completely dry before placing them back into the vacuum to prevent damage to the motor.

4.2. Brush Roll Cleaning

Periodically check the soft brush roll for any tangled hair, strings, or debris. Use the provided cleaning brush tool or scissors to carefully cut away and remove any obstructions. This prevents the brush roll from seizing and maintains effective cleaning.

5. Troubleshooting

If you experience issues with your vacuum cleaner after replacing parts, consider the following:

  • Reduced Suction:
    • Check if filters are clean and completely dry. Clogged or wet filters can severely reduce suction.
    • Ensure all filters are correctly installed and seated.
    • Verify that the dust cup is properly attached and not full.
  • Unusual Noises from Floor Nozzle:
    • Inspect the brush roll for any foreign objects (e.g., coins, small toys) that might be caught.
    • Ensure the brush roll is correctly installed and rotates freely.
  • Brush Roll Not Spinning:
    • Check for hair or debris heavily tangled around the brush roll. Clean as described in Section 4.2.
    • Ensure the brush roll cover is securely fastened.

6. Specifications

FeatureDetail
CompatibilityShark APEX UpLight LZ600, LZ601, LZ602, LZ602C Series Vacuum Cleaners
Part TypeVacuum Cleaner Replacement Parts (Brushes, Filters)
Equivalent Part Numbers# XFFLZ600, # XHFFC600, #145FC600
Brush Roll DimensionsLength: 22 cm, Diameter: 1.8 cm
Pre-Motor Filter DimensionsHeight: 86 mm, Base Diameter: 85 mm, Top Diameter: 38 mm
Post-Motor HEPA Filter DimensionsHeight: 91 mm, Width: 89 mm
Foam Filter DimensionsHeight: 66 mm, Diameter: 74 mm
MaterialHigh-strength and environmental protection material
Approx. Package Weight0.5 kg
Dimensions of the brush roll

Figure 6: Brush Roll Dimensions

Dimensions of the pre-motor filter

Figure 7: Pre-Motor Filter Dimensions

Dimensions of the post-motor HEPA filter

Figure 8: Post-Motor HEPA Filter Dimensions

Dimensions of the foam filter

Figure 9: Foam Filter Dimensions

7. User Tips

  • For households with pets, consider cleaning the brush roll and pre-motor filters more frequently than recommended to maintain optimal performance and prevent odors.
  • Always have a spare set of filters on hand. This allows you to continue using your vacuum while a cleaned set of filters is air-drying.
  • When cleaning filters, use only water. Avoid detergents or harsh chemicals, as these can damage the filter material and reduce their effectiveness.
  • Regularly check the condition of your brush roll. If bristles appear worn or damaged, it may be time for a replacement to ensure effective debris pickup.

8. Warranty and Support

For specific warranty information regarding this replacement parts kit, please refer to the original purchase documentation or contact the seller directly. If you encounter any issues that cannot be resolved using the troubleshooting guide, please reach out to the customer support of the retailer where you purchased the kit for further assistance.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.