FLYSKY FS-i6X

Contents

FLYSKY FS-i6X 10-Channel 2.4GHz AFHDS 2A RC Transmitter User Manual

Model: FS-i6X

Introduction

The FLYSKY FS-i6X is a 10-channel 2.4GHz AFHDS 2A (Automatic Frequency Hopping Digital System Second Generation) radio control transmitter designed for fixed-wing aircraft, gliders, and helicopters. It offers superior protection against interference, low power consumption, and high receiver sensitivity, making it a reliable choice for various RC models.

This manual provides essential information for setting up, operating, maintaining, and troubleshooting your FS-i6X transmitter and compatible receivers.

FLYSKY FS-i6X Transmitter with Multi-channel Hopping Frequency and Omni-directional Gain Antenna labels

Figure 1: FLYSKY FS-i6X RC Transmitter

Package Contents

Please inspect the package contents carefully. Depending on your purchase, your package may include:

  • FLYSKY FS-i6X RC Transmitter
  • One or more compatible receivers (e.g., X6B, iA6B, A8S, iA10B)
  • USB Cable (for online updates and simulator use)
  • Quick Start Guide / Instruction Manual
  • Stickers (optional)

Video 1: Unboxing the FLYSKY FS-i6X Transmitter and accessories.

FLYSKY FS-i6X Transmitter with various receiver options (IA6B, IA10B, A8S, X6B) and USB cable

Figure 2: FS-i6X Transmitter with various compatible receivers and USB cable.

Setup

1. Battery Installation

  1. Open the battery compartment cover on the back of the transmitter.
  2. Insert four (4) 1.5V AA batteries, ensuring correct polarity.
  3. Close the battery compartment cover securely.
Open battery compartment of the FS-i6X transmitter showing slots for four AA batteries

Figure 3: Battery Compartment

2. Receiver Connection and Binding

The FS-i6X transmitter uses the AFHDS 2A system, which requires binding the receiver to the transmitter. Each transmitter and receiver pair has a unique ID to prevent interference.

  1. Connect the receiver to your model's power source (e.g., flight controller, ESC with BEC).
  2. Put the receiver into binding mode (refer to your specific receiver's manual for exact steps, usually involving a bind plug or button).
  3. Turn on the FS-i6X transmitter while holding the bind button (if applicable) or initiating the bind sequence through the transmitter's menu.
  4. Once bound, the receiver's LED will indicate a successful connection (e.g., solid light).
  5. Turn off both the transmitter and receiver, then power them on normally to confirm the binding.

Note: The FS-i6X supports various receivers like X6B, iA6B, A8S, and iA10B. Ensure your receiver is compatible and correctly wired to your model.

3. Throttle Mode Selection

The FS-i6X supports two throttle modes:

  • Mode 1: Right throttle hand (throttle stick on the right side).
  • Mode 2: Left throttle hand (throttle stick on the left side).

Select the mode that suits your preference in the transmitter's settings menu.

Operating Instructions

1. Basic Controls

The FS-i6X features standard RC transmitter controls:

  • Sticks: Control primary flight surfaces (throttle, aileron, elevator, rudder).
  • Switches: Used for various functions like flight modes, gear, flaps, etc.
  • Knobs (VR): Provide proportional control for auxiliary channels.
Front view of the FS-i6X transmitter showing sticks, switches, and knobs

Figure 4: FS-i6X Transmitter Front View

2. LCD Display

The transmitter features an STN Transflective LCD (128x64 Lattice, VA 73x39mm) with white backlight. This display provides real-time information about your model, including battery voltage, signal strength, and channel values. Navigate through menus using the buttons adjacent to the screen.

Close-up of the FS-i6X LCD backlight dot matrix screen displaying flight data

Figure 5: LCD Display

3. Advanced Features

  • Bidirectional Communication: The system supports data backhaul, allowing the transmitter to receive data from various sensors (temperature, altitude, etc.) on your model. This enhances control and safety.
  • Multi-channel Hopping Frequency: The 2.4GHz system automatically hops between 135 channels to minimize interference, ensuring a stable connection up to 500m in ideal conditions.
  • Online Update: The transmitter supports online firmware updates via the USB cable, allowing you to expand channels (up to 10) and access new features.
  • Trainer Port: A PS/2 port is available for trainer functionality, allowing two transmitters to be linked for instruction or dual control.
Diagram illustrating bidirectional data transmission between transmitter and receiver

Figure 6: Bidirectional Data Transmission

Close-up of the PS/2 Trainer port on the back of the FS-i6X transmitter

Figure 7: Trainer Port

Maintenance

  • Keep the transmitter clean and free from dust and moisture. Use a soft, dry cloth for cleaning.
  • Avoid exposing the transmitter to extreme temperatures or direct sunlight for prolonged periods.
  • Remove batteries if the transmitter will not be used for an extended period to prevent leakage.
  • Regularly check all switches, sticks, and knobs for proper function and smooth movement.
  • Ensure the antennas are not bent or damaged.

Troubleshooting

  • No Power: Check battery installation and ensure batteries are charged. The transmitter requires 4xAA batteries (6V DC).
  • Low Voltage Warning: The transmitter will alert you if the voltage drops below 4.2V. Replace or recharge batteries immediately.
  • Loss of Signal/Interference: Ensure the transmitter and receiver are properly bound. The AFHDS 2A system is designed to minimize interference, but extreme environmental factors can still affect signal. Maintain line of sight and avoid operating near strong electromagnetic sources.
  • Receiver Not Responding: Re-bind the receiver to the transmitter. Check all connections between the receiver and your model's components.
  • Channels Not Working: Verify channel assignments in the transmitter's menu. Ensure the receiver supports the desired number of channels (default 6, expandable to 10 via firmware update).

Specifications

FLYSKY FS-i6X Transmitter

FeatureSpecification
Channels6-10 (Default 6)
ModeMode 1 (Right Throttle) / Mode 2 (Left Throttle)
Model TypeFixed-Wing/Glider/Helicopter
RF Range2.408-2.475GHz
RF Power< 20dBm
RF Channel135
Bandwidth500KHz
2.4GHz SystemAFHDS 2A / AFDHS
Modulation TypeGFSK
Stick Resolution4096
Low Voltage Warning< 4.2V
DSC PortPS/2 Port PPM
ChargeableNo
Antenna Length26mm (Dual Antenna)
Weight392g
Power6V DC 1.5AA*4
DisplaySTN Transflective, LCD 128x64 Lattice, VA 73x39mm, White Backlight
Size174x89x190mm
Online UpdateYes
ColorBlack
CertificatesCE0678, FCC ID: N4ZFLYSKYI6X

Compatible Receivers

X6B i-BUS Receiver

FeatureSpecification
Channels6(PWM), 8(PPM), 18(i-BUS)
Model TypeMulti-Rotor
RF Range2.408-2.475 GHz
Bandwidth500KHz
Number of Bands135
RF Power< 20 dBm
RX Sensitivity-95dBm
2.4GHz ProtocolAFHDS 2A
Modulation TypeGFSK
Stick Resolution1024
Low Voltage AlarmYes
DSC PortPPM/PWM/i-BUS
Antenna Length93mm (Dual Antenna)
Power Input4.0-8.4V
Online UpdateYes (Wireless)
Range>300m
Weight4.5g
Size36*22*7.5mm
i-BUS PortYes
CertificatesCE0678, FCC ID: N4ZX6B00

FS-IA6B Receiver

FeatureSpecification
Channels6
Model TypeFixed Wing/Helicopter/Glider
RF Receiver Sensitivity-105dBm
ModulationGFSK
System TypeAFHDS2A/AFHDS
Channel Resolution1024 steps
Bind PortYes
Power PortYes (VCC)
Power4V - 6.5V DC
Weight14.9g
Antenna Length26mm
Size47.4*262.2*15 mm
CertificatesCE, FCC

FS-A8S Receiver

FeatureSpecification
ChannelsPPM 8CH, i-BUS 18CH
Model TypeMulti-Rotor
Frequency Range2.408-2.475GHz
Bandwidth500KHz
Number of Bands135
RX Sensitivity-92 dBm
2.4GHz SystemAFHDS 2A
Modulation TypeGFSK
DSC PortPPM/i-BUS/S.BUS
Transfer MethodFHSS
Data Output1.5mm*3 Pin PPM/i-BUS/S.BUS
Antenna Length26mm (Not including brass contacts)
Input Power Supply4.0-8.4V
Display MethodLED
Range (No ground interference)>300m
Working Current40mA
Channel Delay<15mS
Size20*14*5.3mm
Weight1.2g
CertificatesCE0678, FCCID: N45ZA8S00

User Tips

  • The FS-i6X is praised for its easy control, enhancing the remote control experience for various toy vehicles.
  • Its lightweight design and composite material construction contribute to its portability and durability.
  • Remember that the transmitter comes with 6 channels by default. If you require 10 channels, a firmware modification is necessary.

Warranty and Support

The FLYSKY FS-i6X transmitter is certified with CE0678 and FCC ID: N4ZFLYSKYI6X, indicating compliance with relevant safety and electromagnetic compatibility standards.

For technical support, firmware updates, or further assistance, please refer to the official FLYSKY website or contact your retailer.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.