1. Introduction
This manual provides detailed instructions for the installation, setup, operation, and maintenance of your Flysky FS-R9B (8-channel) and FS-R6B (6-channel) 2.4G digital receivers. These receivers are designed for use with various RC models, including fixed-wing aircraft and helicopters, and are compatible with Flysky's AFHDS 2A (Automatic Frequency Hopping Digital System 2A) protocol.
Please read this manual thoroughly before operating your receiver to ensure safe and efficient use.
2. Product Overview
The Flysky FS-R9B and FS-R6B are compact and reliable 2.4GHz receivers. The FS-R9B offers 8 channels, while the FS-R6B provides 6 channels, catering to different control requirements for your RC models. Both receivers utilize advanced GFSK modulation and the AFHDS 2A system for robust and interference-free communication with compatible Flysky transmitters.
3. Specifications
3.1. Flysky FS-R9B Receiver Specifications
| Feature | Specification |
|---|---|
| Channels | 8 channels |
| Receiving Sensitivity | -105dBm |
| Frequency Range | 2.4-2.48GHz |
| Frequency Width | 500KHz |
| Wave Band | 160 |
| Modulation | GFSK |
| 2.4G Mode | Automatic FM digital system |
| Remote Control Distance | 500-1000M |
| Channel Resolution | 1024 classes |
| Power | 4.0-6.55V DC |
| Weight | 18g |
| Antenna Length | 26mm |
| Size | 53 x 35 x 15mm |
| Usage | Fixed-wing copters, helicopters |
| Certification | CE |
3.2. Flysky FS-R6B Receiver Specifications
| Feature | Specification |
|---|---|
| Channels | 6 Channels |
| Model Type | Heli/Airplane |
| RF Power | Less than 20DBm |
| Modulation | GFSK |
| Code Type | PCM |
| Sensitivity | 1024 |
| Low Voltage Warning | LED |
| DSC Port | Yes (PS2; output: PPM) |
| Charger Port | Yes |
| Antenna Length | 26mm |
| Frequency | 2.4G |
| Power | 5V DC |
| Weight | 25g |
| Size | 30 x 25 x 8mm |
4. Setup and Binding
4.1. Components
Each receiver typically includes:
- Flysky FS-R9B or FS-R6B Receiver
- Bind Plug
4.2. Receiver Port Identification (FS-R9B Example)
The receiver features multiple channels (CH1-CH8 for FS-R9B, CH1-CH6 for FS-R6B), a dedicated battery input (BAT), and a BIND port for pairing with your transmitter.
4.3. Binding Process
To establish communication between your Flysky receiver and transmitter, follow these steps:
- Ensure your transmitter is turned OFF.
- Insert the bind plug into the 'BIND' port on your receiver.
- Connect power to the receiver via the 'BAT' port. The receiver's LED indicator should start flashing rapidly, indicating it is in binding mode.
- While holding down the 'BIND' button (or activating bind mode) on your transmitter, turn the transmitter ON.
- Observe the receiver's LED. Once binding is successful, the LED should stop flashing and remain solid.
- Release the 'BIND' button on your transmitter (if applicable) and turn off both the receiver and the transmitter.
- Remove the bind plug from the receiver.
- Turn on the transmitter first, then power on the receiver. The receiver's LED should illuminate solid, confirming a successful connection.
Note: The exact binding procedure may vary slightly depending on your specific Flysky transmitter model. Refer to your transmitter's manual for precise instructions.
4.4. Installation in RC Model
- Mount the receiver securely in your model using double-sided tape or hook-and-loop fasteners. Ensure it is protected from vibrations and moisture.
- Position the antenna(s) away from metal parts, motors, ESCs, and other electronic components that could cause interference. For optimal signal reception, ensure the antenna tip is exposed and oriented correctly (typically perpendicular to each other if dual antennas are present).
- Connect your servos, ESC, and other components to the appropriate channels on the receiver.
4.5. Compatibility
These receivers are compatible with Flysky 2.4G AFHDS 2A protocol transmitters. This includes, but is not limited to, models such as:
- Turnigy 9X
- Flysky FS-TH9B
- Flysky FS-i10
- Flysky FS-i8
- Flysky FS-T6
- Flysky FS-T4B
- Flysky FS-CT6B
5. Operation
Once the receiver is successfully bound to your transmitter and installed in your model, operation is straightforward:
- Always turn on your transmitter first.
- Then, power on your RC model, which will power the receiver.
- Verify that the receiver's LED is solid, indicating a stable connection.
- Test all control surfaces and functions before flight or operation.
- When finished, turn off power to the RC model first, then turn off your transmitter.
The FS-R6B model features a Low Voltage Warning LED. If this LED starts to flash during operation, it indicates that the receiver's input voltage is dropping, and you should land or cease operation immediately to prevent loss of control.
6. Maintenance
- Keep the receiver clean and free from dust, dirt, and moisture.
- Avoid exposing the receiver to extreme temperatures or direct sunlight for prolonged periods.
- Regularly inspect all wiring and connections for signs of wear or damage.
- Ensure the antenna(s) are not kinked, cut, or damaged, as this can significantly reduce range and signal quality.
- Store the receiver in a dry, cool place when not in use.
7. Troubleshooting
7.1. Receiver Not Binding
- Ensure the bind plug is fully inserted into the 'BIND' port.
- Verify that the receiver is receiving adequate power (within the specified voltage range).
- Confirm your transmitter is in bind mode and is compatible with the AFHDS 2A protocol.
- Try moving the transmitter closer to the receiver during the binding process.
- Ensure no other 2.4GHz devices are causing interference during binding.
7.2. Loss of Signal / Intermittent Connection
- Check antenna placement. Ensure they are not obstructed by carbon fiber or metal parts and are oriented for optimal reception.
- Verify the power supply to the receiver is stable and sufficient.
- Ensure the transmitter's batteries are fully charged.
- Check for potential sources of interference in your operating environment (e.g., Wi-Fi routers, other 2.4GHz devices).
- Re-bind the receiver to the transmitter.
7.3. Controls Not Responding Correctly
- Ensure servos and other components are connected to the correct channels on the receiver.
- Check for proper calibration and settings on your transmitter.
- Verify that all connections are secure and free from damage.
8. User Tips
- Transmitter Compatibility: These receivers are confirmed to be compatible with the Turnigy 9X transmitter, as well as other Flysky AFHDS 2A transmitters. Always ensure your transmitter is set to the correct protocol.
- Antenna Orientation: For best range and signal reliability, try to position the receiver's antenna(s) at a 90-degree angle to each other (if dual antennas) and away from large metal or carbon fiber components.
- Power Supply: Ensure your power source (e.g., BEC from ESC, separate receiver battery) provides stable voltage within the receiver's specified range (4.0-6.55V DC for FS-R9B, 5V DC for FS-R6B).
9. Warranty and Support
For any issues not covered in this manual, or for warranty claims, please contact your original point of purchase or the Flysky customer support directly. Keep your purchase receipt as proof of purchase.
Flysky products are designed for hobby use. Misuse, modification, or operation outside of specified parameters may void your warranty.