Shark BRUSHROLL BRISTLE BAR GRAY (Compatible with Shark SV1110, SV1100, SV1106, SV1106N, SV1112)

Contents

Shark Vacuum Cleaner Brushroll Replacement Manual

Model: BRUSHROLL BRISTLE BAR GRAY

Compatible with Shark SV1110, SV1100, SV1106, SV1106N, SV1112 Series Vacuum Cleaners

1. Introduction

This manual provides instructions for the proper installation, function, and maintenance of your replacement brushroll for compatible Shark vacuum cleaner models. This brushroll is designed to effectively agitate carpet fibers and sweep debris into the vacuum's suction path, ensuring optimal cleaning performance.

2. Setup and Installation

The brushroll is a key component for your vacuum's cleaning effectiveness. Proper installation ensures optimal performance and longevity of the part.

2.1 Before Installation

  • Ensure your vacuum cleaner is unplugged from the power outlet before attempting any installation or maintenance.
  • Place the vacuum cleaner on a clean, flat surface.
  • Refer to your specific Shark vacuum cleaner's user manual for detailed instructions on how to access the brushroll compartment.

2.2 Installation Steps

  1. **Access Brushroll Compartment**: Typically, this involves flipping the vacuum head over and unlatching or unscrewing a cover plate to expose the brushroll.
  2. **Remove Old Brushroll**: Carefully lift out the old brushroll. Note the orientation of the end caps and how it sits in its housing.
  3. **Clean Compartment**: Remove any accumulated hair, debris, or obstructions from the brushroll compartment and end caps.
  4. **Insert New Brushroll**: Align the new brushroll (eelhoe brand) with the designated slots or bearings in the vacuum head. Ensure the end caps fit securely into their respective positions. The brushroll should spin freely when correctly installed.
  5. **Secure Cover**: Reattach the cover plate and secure any latches or screws that were removed.
Full view of the replacement brushroll with close-ups of bristles and end cap.
Figure 1: Full view of the replacement brushroll, highlighting the bristle pattern and end cap design.
Close-up of the brushroll end cap, showing the connection point.
Figure 2: Close-up of the brushroll's end cap, which connects to the vacuum's drive mechanism.

3. Operating the Brushroll

The brushroll operates automatically when the vacuum cleaner is powered on and engaged in cleaning mode. Its primary function is to:

  • **Agitate Carpets**: The bristles rotate to loosen dirt and debris embedded in carpet fibers.
  • **Sweep Hard Floors**: On hard surfaces, the brushroll sweeps loose particles into the suction path.
  • **Maintain Suction**: A clean, properly functioning brushroll contributes to consistent airflow and effective suction.

Ensure the brushroll is free from obstructions before and during operation to prevent damage to the vacuum or the brushroll itself.

4. Maintenance

Regular maintenance of the brushroll is crucial for extending its lifespan and maintaining your vacuum's cleaning efficiency.

4.1 Cleaning the Brushroll

  • **Frequency**: Inspect the brushroll after each use, especially if vacuuming areas with long hair or pet fur.
  • **Procedure**:
    1. Unplug the vacuum cleaner.
    2. Remove the brushroll as described in the installation section.
    3. Use scissors or a brush to carefully cut and remove any tangled hair, string, or debris from the bristles and around the end caps.
    4. Wipe the brushroll and its housing with a dry cloth.
    5. Reinstall the clean brushroll.

4.2 Replacement Schedule

It is recommended to replace the brushroll every 2 to 3 months, depending on usage frequency and the type of debris typically vacuumed. This ensures the bristles remain effective and the vacuum operates at its best performance.

Close-up of the brushroll bristles, showing their density and pattern.
Figure 3: Close-up of the brushroll bristles. Regularly check for wear and tear or embedded debris.

5. Troubleshooting

If you experience issues with your vacuum cleaner's brushroll, consider the following common problems and solutions:

ProblemPossible CauseSolution
Brushroll not spinningHair/debris tangled; worn belt (if applicable); improper installationClean brushroll thoroughly; check for belt damage (consult vacuum manual); re-install brushroll correctly.
Reduced cleaning performanceWorn bristles; brushroll obstructedReplace brushroll if bristles are worn; clean brushroll of debris.
Unusual noise from brushroll areaDebris caught; damaged brushroll or bearingsRemove debris; inspect brushroll for damage and replace if necessary.

6. Specifications

FeatureDetail
Part TypeBRUSHES (Brushroll / Bristle Bar)
ColorGray
Compatible ModelsShark SV1110, SV1100, SV1106, SV1106N, SV1112
Brushroll Brandeelhoe
OriginMainland China
High-concerned chemicalNone
Package Dimensions (approx.)Length: 10 cm, Width: 5 cm, Height: 3 cm
Package Weight (approx.)0.093 kg

7. User Tips

  • For households with pets, consider more frequent brushroll cleaning to prevent hair buildup and maintain suction.
  • Always ensure the brushroll is completely dry before reinstalling it into the vacuum cleaner.
  • If you notice a significant decrease in cleaning performance even after cleaning the brushroll, it may be time for a replacement.

8. Warranty and Support

For warranty information regarding this replacement brushroll, please refer to the terms provided by the original seller or manufacturer (eelhoe). For support related to your Shark vacuum cleaner, please consult the official Shark documentation or customer service channels.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.