VGR V-282 Professional Hair Clipper Instruction Manual

1. Introduction

Thank you for choosing the VGR V-282 Professional Hair Clipper and V-982 Hair Trimmer. This manual provides essential information for the safe and effective use, maintenance, and care of your new grooming tools. Please read these instructions carefully before first use and keep them for future reference.

The VGR V-282 Hair Clipper features a powerful rotary motor, professional stainless steel blades, an adjustable taper lever, and a clear LED display. The VGR V-982 Hair Trimmer offers precise trimming with its own set of guide combs and a compact design.

2. What's Included

Your package should contain the following items:

• 1 x VGR V-282 Hair Clipper
• 1 x VGR V-982 Hair Trimmer
• 6 x Guide Combs for V-282 (1.5mm, 3mm, 4.5mm, 6mm, 10mm, 13mm)
• 4 x Guide Combs for V-982 (1mm, 2mm, 3mm, 4mm)
• 1 x USB Charging Cable
• 1 x Cleaning Brush
• 1 x Hair Comb
• 1 x Lubricating Oil

3. Specifications

VGR V-282 Hair Clipper

VGR V-982 Hair Trimmer

4. Setup

4.1 Initial Charging

Before first use, fully charge your hair clipper and trimmer. The devices are equipped with a 2000 mAh Li-ion battery (V-282) and a 600mAh battery (V-982) respectively, and support convenient USB charging.

• Connect the USB charging cable to the charging port on the device.
• Plug the other end of the USB cable into a compatible USB power source (e.g., computer, laptop, USB charger, power bank).
• The LED display will show the charging progress and remaining battery percentage.
• The V-282 clipper takes approximately 3 hours to fully charge, providing up to 200 minutes of working time.

4.2 Attaching Guide Combs

To achieve desired hair lengths, attach the appropriate guide comb to the clipper or trimmer head.

• Select the guide comb corresponding to your desired cutting length (e.g., 1.5mm, 3mm, 4.5mm, 6mm, 10mm, 13mm for V-282; 1mm, 2mm, 3mm, 4mm for V-982).
• Align the comb with the blade and push it firmly until it clicks into place.
• To remove, gently pull the comb away from the blade.

5. Operating Instructions

5.1 Power On/Off

Locate the ON/OFF switch on the side of the clipper/trimmer. Slide the switch to turn the device on or off.

5.2 Adjusting Cutting Length (V-282 Clipper)

The V-282 clipper features an adjustable taper lever on the side, allowing you to fine-tune the cutting length between 0.8mm and 2mm without changing guide combs. This is in addition to the length provided by the guide combs (up to 13mm).

• Move the taper lever up for a closer cut (0.8mm).
• Move the taper lever down for a longer cut (2mm).

5.3 Hair Cutting Techniques

The VGR V-282 and V-982 are suitable for both wet and dry haircuts. For best results:

• Ensure hair is clean and detangled.
• Start with a longer guide comb and gradually reduce the length if desired.
• Move the clipper/trimmer against the direction of hair growth for an even cut.
• Use smooth, overlapping strokes.
• For detailing and edging, use the V-982 trimmer without a guide comb.

6. Maintenance

Proper maintenance ensures the longevity and optimal performance of your VGR hair clipper and trimmer.

6.1 Cleaning the Blades

The blades are designed for easy cleaning, including washing under water.

• After each use, turn off the device and remove any attached guide comb.
• Use the provided cleaning brush to brush away loose hairs from the blades.
• For a more thorough clean, you can rinse the blades under running water. Ensure the device is turned off and disconnected from power before rinsing.
• Allow the blades to air dry completely before reattaching or storing.

6.2 Oiling the Blades

Regular oiling helps maintain blade sharpness and smooth operation.

• After cleaning and drying the blades, apply a few drops of the provided lubricating oil to the teeth of the blades.
• Turn on the device for a few seconds to allow the oil to distribute evenly.
• Wipe off any excess oil with a clean cloth.

7. Troubleshooting

Common Issues and Solutions

• Device not turning on: Ensure the device is fully charged. If using corded, check the power connection.
• Blades pulling hair or cutting poorly: The blades may be dull or clogged with hair. Clean and oil the blades as described in the Maintenance section. If the issue persists, consider professional sharpening or blade replacement.
• Reduced battery life: Ensure the device is fully charged before each use. Over time, battery capacity may decrease.
• Excessive noise or vibration: Ensure the blades are properly aligned and free of debris. Clean and oil the blades.

8. User Tips

• Versatile Use: Both the V-282 clipper and V-982 trimmer can be used for dry and wet haircuts, offering flexibility for your grooming routine.
• Precision Control: Utilize the adjustable taper lever on the V-282 clipper for seamless blending and precise length control between guide comb settings.
• Regular Cleaning: Always clean and oil the blades after each use to maintain their sharpness and prevent hair buildup, which can affect performance.
• Full Charge: For optimal performance and maximum runtime, ensure your devices are fully charged before starting a haircut. The LED display helps monitor battery levels.
• Explore Lengths: Experiment with the various guide combs provided for both the clipper and trimmer to find your preferred cutting lengths and styles.

9. Warranty & Support

All VGR products come with a 12-month warranty from the date of purchase, covering manufacturing defects. This warranty ensures that the product is free from defects in material and workmanship under normal use.

If you encounter any issues with your VGR V-282 Hair Clipper or V-982 Hair Trimmer, please refer to the troubleshooting section first. For further assistance or to claim warranty service, please contact your retailer or the VGR customer support team.

Please retain your proof of purchase for warranty claims.