Introduction
This manual provides instructions for the XINOWY Type-C Earphone Speaker Accessories Dual Microphone, designed for use with Teleheer V6 plus and XINOWY V6 Plus motorcycle helmet Bluetooth intercom systems. This product is an accessory headset and does not function as a standalone intercom unit.
The headset features DSP noise cancellation and supports A2DP for ultra-clear stereo sound quality, enhancing your communication and audio experience while riding.
Image: Illustration of DSP noise cancelling and A2DP ultra clear stereo sound quality.
Setup and Installation
Before installation, ensure your intercom unit (Teleheer V6 plus or XINOWY V6 Plus) is powered off.
- Identify Components: The package includes two speakers, a boom microphone, a soft wire microphone, and a Type-C connector cable. An adhesive pad is also provided for mounting.
Image: Overview of the headset components and compatible intercom units.
- Choose Microphone: Select the appropriate microphone for your helmet type:
- Boom Microphone: Recommended for open-face, modular, or flip-up helmets.
- Soft Wire Microphone: Recommended for full-face helmets.
Image: Headset with boom microphone.
Image: Headset with soft wire microphone.
- Install Speakers: Position the two speakers inside your helmet's ear pockets. Use the adhesive pads if necessary to secure them. Ensure they are centered over your ears for optimal sound.
- Install Microphone:
- For boom microphone: Attach it to the inside of the helmet near your mouth, ensuring it is close enough to pick up your voice clearly but not obstructing your vision or comfort.
- For soft wire microphone: Route the microphone to the front of the helmet, positioning it inside the chin bar near your mouth.
- Connect to Intercom: Locate the Type-C port on your Teleheer V6 plus or XINOWY V6 Plus intercom unit. Carefully insert the Type-C connector of the headset into this port.
Image: Detail of the Type-C connector.
- Cable Management: Route all cables neatly within the helmet padding to prevent tangling, discomfort, or interference with helmet operation. Use any provided clips or adhesive strips to secure the cables.
Operating Instructions
This headset functions as an audio input/output device for your compatible motorcycle Bluetooth intercom unit. All primary controls for communication, music playback, and volume will be managed directly through your Teleheer V6 plus or XINOWY V6 Plus intercom.
- Power On/Off: The headset draws power from the intercom unit. Power on/off your intercom as usual.
- Audio Playback: Once connected, audio from your intercom (music, GPS, phone calls, intercom communication) will be routed through the headset speakers.
- Microphone Use: The selected microphone will capture your voice for intercom conversations and phone calls. The integrated DSP noise cancellation helps reduce background noise for clearer communication.
Care and Maintenance
- Cleaning: Gently wipe the speakers and microphone with a soft, dry cloth. If necessary, a slightly damp cloth can be used, but ensure no moisture enters the electronic components. Do not use harsh chemicals or abrasive cleaners.
- Storage: Store the headset in a dry place, away from direct sunlight and extreme temperatures.
- Cable Care: Avoid sharp bends or excessive pulling on the cables to prevent damage.
- Speaker/Mic Covers: If the foam covers on the speakers or microphone become worn or dirty, they can often be gently removed and replaced (replacement covers may be sold separately).
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from speakers. | Headset not properly connected; intercom unit off or muted; speaker wires damaged. | Ensure Type-C connector is fully inserted. Check intercom unit's power and volume. Inspect cables for visible damage. |
| Microphone not picking up voice. | Microphone not properly connected; microphone positioned too far from mouth; intercom unit microphone muted. | Verify microphone connection. Adjust microphone position closer to your mouth. Check intercom unit's microphone settings. |
| Poor sound quality or excessive noise. | Speakers incorrectly positioned; microphone picking up wind noise; loose connection. | Adjust speaker placement for optimal audio. Ensure microphone is shielded from direct wind. Re-seat Type-C connector. |
| Headset not compatible with my intercom. | Incorrect intercom model. | This headset is specifically designed for Teleheer V6 plus and XINOWY V6 Plus intercoms. Compatibility with other models is not guaranteed. |
Specifications
| Feature | Detail |
|---|---|
| Model Name | V6 plus Helmet Intercom earphone |
| Item Type | Helmet Headset |
| Special Features | Noise Reduction (DSP), A2DP Ultra Clear Stereo Sound |
| Connectivity | Type-C |
| Microphone Type | Dual Microphone (Boom and Soft Wire options) |
| Applicable Helmet Type | Half Helmet, MODULAR, MOTOCROSS, Open face, Full Face, Flip Up Helmet, Universal |
| Maximum Number of Speakers | 2 (stereo speakers) |
| Item Weight | 0.2 kg |
| Item Dimensions (L x W x H) | 5.4 cm x 8.9 cm x 2.2 cm |
| External Testing Certification | CE |
| Battery Included | Yes (Refers to the compatible intercom unit's battery, as this is an accessory) |
| High-concerned chemical | None |
| Origin | Mainland China |
Note: Specifications like "Maximum Intercom Distance" (<500m) are properties of the main intercom unit (Teleheer V6 plus / XINOWY V6 Plus) to which this headset connects, not the headset itself.
User Tips
- Quantity Options: When purchasing, "1pc" refers to one headset unit, while "2pcs" refers to two headset units. Ensure you select the correct quantity based on your needs.
- Intercom Compatibility: This headset is specifically designed for Teleheer V6 plus and XINOWY V6 Plus intercoms. While it may physically connect to other Type-C devices, full functionality and optimal performance are only guaranteed with the specified intercom models.
- Microphone Placement: Experiment with microphone placement to find the sweet spot that minimizes wind noise and maximizes voice clarity for your specific helmet and riding style.
Warranty and Support
For any issues encountered with your XINOWY V6 Plus Helmet Intercom Headset, please contact the seller directly. Providing clear pictures or videos demonstrating the problem will assist in receiving the best possible solution.
Keep your purchase records for warranty claims. The manufacturer's warranty covers defects in materials and workmanship under normal use.
